• Wind and Structures
• /
• v.20 no.2
• /
• pp.349-361
• /
• 2015

Higher-mode vertical vortex-induced vibrations (VIV) have been observed on several steel box-girder suspension bridges where different vertical modes are selectively excited in turn with wind velocity in accordance with the Strouhal law. Understanding the relationship of VIV amplitudes for different modes of vibration is very important for wind-resistant design of long-span box-girder suspension bridges. In this study, the basic rectangular cross-section with side ratio of B/D=6 is used to investigate the effect of different modes on VIV amplitudes by section model tests. The section model is flexibly mounted in wind tunnel with a variety of spring constants for simulating different modes of vibration and the non-dimensional vertical amplitudes are determined as a function of reduced velocity U/fD. Two 'lock-in' ranges are observed at the same onset reduced velocities of approximately 4.8 and 9.4 for all cases. The second 'lock-in' range, which is induced by the conventional vortex shedding, consistently gives larger responses than the first one and the Sc-normalized maximum non-dimensional responses are almost the same for different spring constants. The first 'lock-in' range where the vibration frequency is approximately two times the vortex shedding frequency is probably a result of super-harmonic resonance or the "frequency demultiplication". The main conclusion drawn from the section model study, central to the higher-mode VIV of suspension bridges, is that the VIV amplitude for different modes is the same provided that the Sc number for these modes is identical.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.862-867
• /
• 2009

This paper presents a study on a rectenna for rectification of incident low power microwave signals with power densities less than 2 mW/$cm^2$ at 2.45 GHz. The proposed rectenna is designed and implemented by a rectifier with voltage doubler structure and a printed Yagi antenna which suppress re-radiation of the second order harmonic of fundamental frequency. The printed Yagi antenna has a gain of about 5 dB, and the measured conversion efficiencies of the rectenna are from 32 % to 42 % when its incident power levels are from 0 dBm to 14 dBm. The developed rectenna is expected to be useful in the power transmission system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1612-1619
• /
• 2001

This paper examines the design, implementation characteristics of a folded dipole active integrated antenna. Our goal was to minimize the physical size of RF circuit and its insertion loss, and to make the high frequency tuning easier by directly integrating the ISM(Industrial Scientific & Medical) band power amplifier and antenna. Non-linear model has been used for highly accurate simulation of the power amplifier. The maximum power level was found by using the Load pull method before an impedance matching was achieved. It is found that the total power-added efficiency(PAE) including the driving amplifier was 31.5% and that the transmit power was 13.7 dBm. We also found that the proposed scheme with the smaller antenna as compared with the existing dipole antenna has 23.7 dB total gain including the antenna gain. The suppression of the second harmonic signal to the fundamental signal with respect to the fundamental signal was found to be more than 30 dBc.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.43-46
• /
• 2018

This paper has designed a wideband bandpass filter (WBSF : Wide Band Stop Filter) using a stepped impedance resonator (SIR : Stepped Impedance Resonator) with improved performance and improved hairpin coupling structure. The SIR WBSF is small in size and has the advantage of having excellent bandstop characteristics. The designed BSF has a structure in which a quadrangular shaped hairpin of a / 4 length is arranged symmetrically on the upper and lower sides of the input and output transmission lines. The input and output terminals were terminated at 50 ohms for system applications. The center frequency of the SIR WBSF is 6.3 GHz, which is the second harmonic of 3.15 GHz. The designed filter has a 3dB bandwidth of 2.9 GHz and a transmission coefficient ($S_{21}$) of 33.2 dB. The reflection coefficient ($S_{11}$) at the center frequency is 0.106 dB. The application field is used for fixed microwave relay stations, fixed satellite and earth stations, and fixed satellite communications. The overall size is $20mm{\times}10mm$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.56-61
• /
• 2010

In this paper, high efficient power amplifier with dual band has been realized. Dual band power amplifier have used modify stub matching for single FET, center frequency 2.14GHz and 5.2GHz respectively. The dual-band operation of the CRLH TL is achieved by the frequency offset and the nonlinear phase slope of the CRLH TL for the matching network of the power amplifier. Because the control of the all harmonic components is very difficult m dual-band, we have managed only the second- and third-harmonics to obtain the high efficiency with the CRLH TL in dual-band. Dual-band characteristics in the output has to balance. Two operating frequencies are chosen at 2.14 GHz and 5.2 GHz in this work. The measured results show that the output power of 28.56 dBm and 29 dBm was obtained at 2.14 GHz and 5.2 GHz, respectively. At this point, we have obtained the power-added efficiency (PAE) of 65.824 % and 69.86 % at two operation frequencies, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.45-54
• /
• 2014

In this paper, We have designed and fabricated 20 InP Gunn diodes using a current limiting epitaxial structure by MINT's optimized fabrication processes. We have also packaged the fabricated InP Gunn diodes using our optimized packaging method, and then designed and fabricated a W-band waveguide FTO to measure characteristics of the packaged InP Gunn diodes. The packaged InP Gunn diode have a ceramic ring, a Au plated stud and a lid, and a Maltese cross. The fabricated InP Gunn diodes have good RF characteristics such as high output powers (11.8~17 dBm) and limiting low currents (less than 400 mA) between 92.9 and 94.78 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.725-731
• /
• 2006

A novel design of frequency multiplier using a feedforward technique and a defected ground structure(DGS) is proposed. The feedforward loop in the proposed frequency multiplier suppresses the fundamental component $(f_0)$, the dumb-bell or spiral shaped DGS diminish unwanted harmonics such as second, third and fourth. Due to the combination of the feedforward structure and the DGS, only the multiplied frequency component$(2f_0,\;3f_0,\;4f_0)$ appears at the output port and the other unwanted components are suppressed excellently. The frequency multiplier is designed at 1 GHz $(f_0)$, by the proposed technique and measured. The measured output power of $2f_0,\;3f_0$ and $4f_0$ is -2.59 dBm, -5.36dBm and -4.57dBm, respectively, when the input power is 0dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.250-256
• /
• 2008

In this paper, an X-band oscillator is presented using a new miniaturized microstrip hairpin resonator. The newly designed hairpin resonator on the microstrip line employs the spiral structure, which shows a higher loaded quality factor and the 50 % reduced circuit area compared to the conventional one at 9.2 GHz. The oscillator using proposed resonator shows the output power of 10.87 dBm, the second harmonic suppression of 41.99 dBc, and the phase noise performance of -101.49 dBc/Hz at 100 kHz offset, which is better than the conventional resonator oscillator by 6.17 dB.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.751-756
• /
• 2010

Ultrasonic nonlinearity is very sensitive to changes in material properties. This paper describes the study of the correlation between heat treatment and ultrasonic nonlinearity by taking nonlinear factors into consideration. A modified formula was proposed for ultrasonic velocity. This formula indicated that the changes occurring in nonlinearity during heat treatments cause changes in the ultrasonic velocity. The experimental results show that the relative nonlinearity parameters calculated from the modified ultrasonic velocities and the ratio of amplitudes of the second harmonic and fundamental wave are in good agreement. The experimental results prove that heat treatment can result in changes in material nonlinearity. Moreover, the relative nonlinearity parameter calculated from the modified velocity formula is has a large value. Since this parameter has high sensitivity to changes in nonlinearity, it can be used to represent the relative nonlinearity change calculated in this study by using the modified formula for ultrasonic velocity.

• Structural Engineering and Mechanics
• /
• v.58 no.1
• /
• pp.59-91
• /
• 2016

Laminated composite shells are commonly used in various engineering applications including aerospace and marine structures. In this paper, using semi-analytical finite strip method, the buckling behavior of laminated composite deep as well as thick shells of revolution under follower forces which remain normal to the shell is investigated. The stiffness caused by pressure is calculated for the follower forces subjected to external fibers in thick shells. The shell is divided into several closed strips with alignment of their nodal lines in the circumferential direction. The governing equations are derived based on first-order shear deformation theory which accounts for through thickness-shear flexibility. Displacements and rotations in the middle surface of shell are approximated by combining polynomial functions in the meridional direction as well as truncated Fourier series with an appropriate number of harmonic terms in the circumferential direction. The load stiffness matrix which accounts for variation of loads direction will be derived for each strip of the shell. Assembling of these matrices results in global load stiffness matrix which may be un-symmetric. Upon forming linear elastic stiffness matrix called constitutive stiffness matrix, geometric stiffness matrix and load stiffness matrix, the required elements for the second step analysis which is an eigenvalue problem are provided. In this study, different parameter effects are investigated including shell geometry, material properties, and different boundary conditions. Afterwards, the outcomes are compared with other researches. By considering the results of this article, it can be concluded that the deformation-dependent pressure assumption can entail to decrease the calculated buckling load in shells. This characteristic is studied for different examples.