• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.703-706
• /
• 2004

This paper deals with the various sealing conditions in a vacuum and the discharge characteristics. The MgO thin film is prepared by e-beam evaporation method. Sealing process was performed in a vacuum at panel temperature of 430 $^{\circ}C$. We find the cracks on the MgO film surface, which results in higher discharge voltage and lower luminous efficiency. The vacuum in-line sealing technology does not require additional annealing process but induces the MgO cracks because of the high temperature sealing cycle in a vacuum. Therefore we modify the vacuum in-line sealing cycle which the MgO cracks are not found and the good characteristics of plasma displays are found in higher sealing pressure at sealing temperature of 430 $^{\circ}C$.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.119-126
• /
• 2006

In this paper, the contact behavior characteristics of a primary sealing components such as a seal ring and a seal seat has been presented for a small hydro-power turbine. Using the non-linear FEM analysis, the maximum temperature, the axial displacement, radial differences between a seal ring and a seal seat, and maximum contact normal stress have been analyzed for three optimized sealing profiles in which are designed based on the FEM analysis and Taguchi's experimental method. The three primary sealing profiles between a seal ring and a seal seat are strongly related to a leakage of a water for a hydro-power turbine and wear of a primary sealing component. The computed results show that the contact rubbing area between a seal ring and a seal seat is very important for reducing a friction heating and wear in a sealing gap, and increasing a contact normal stress in primary sealing components. Based on the FEM computation, models II and III in which have a small rubbing surface of seal rings show low dilatation of primary sealing components, and high normal contact stress between a seal ring and a seal seat. Thus, the FEM computed results recommend a short contacting width of a primary sealing component for reducing a leakage and thermal distortions, and expanding a seal life. This means that a conventional primary sealing component may be switched to a reduced sealing face of seal rings.

• 한국가스학회지
• /
• 제16권5호
• /
• pp.52-57
• /
• 2012

본 연구에서는 유한요소해석법을 사용하여 다접오링의 밀봉특성에 관련된 변형률, 응력, 접촉법선응력을 해석하였다. 밀봉특성에 관한 FEM 해석결과에 의하면, 다접오링에 작용하는 최대 변형률, 최대압축응력, 최대접촉 법선응력은 기존의 오링에 비해 약 1.7배나 더 높게 나타났다. 이것은 다접오링의 절단면에 U홈을 형성하였기 때문이고, 다접오링은 고압가스 용기, 밸브, 가스기기의 밀봉을 유지하는데 매우 유용할 것으로 판단된다. 그리고, 다접오링에서 가스압력을 높여도 압출파손 현상이 발생되지 않았는데, 이것은 U홈이 있기 때문인 것으로 판단된다. 따라서, 다접오링은 기존의 오링에 비해 밀봉수명을 길게 연장시킬 수 있다.

• 한국정밀공학회지
• /
• 제14권4호
• /
• pp.56-63
• /
• 1997

Sealing of lubricant-air mixture in the high performance machining center is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry. Velocity, pressure, turbulence intensity of profile is calculated to find more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic. This paper considers a design effect of sealing capability of non- contact type seals for high speed spindle and analyzes leakage characteristics to minimize a leakage 7 on the same sealing area.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.316-320
• /
• 2004

Waterproof fabrics are seamed and sealed by waterproof sealing tape to prevent water from penetrating through the stitch holes. As this process may change the mechanical properties of breathable waterproof fabric related to its deformation with human body, the changes in mechanical properties were investigated. In both of parallel and perpendicular directions, tensile characteristics were remarkably changed with seaming and sealing processes. The increase of LT and WT means that the clothing sealed by waterproofing tape may produce somewhat discomfort feeling. On the other hand, the bridge of the sewing thread seemed to be reinforced by waterproofing tape. Shear characteristics such as G, 2HG, and 2HG5 gradually increased with seaming and sealing processes in parallel direction. However, they decreased with sealing process in perpendicular direction because the seam line would work as an axis located at the center of the testing range.

• 한국가스학회지
• /
• 제18권4호
• /
• pp.51-55
• /
• 2014

본 연구에서는 한곳에서 접촉하는 오링과 여러 곳에서 접촉하는 멀티접촉패킹에 대한 밀봉특성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, LP가스압력 1.8MPa을 공급하였을 때 기존의 오링에서는 밀봉성에 관련된 2.5MPa의 수직접촉 최대응력을 발생하였다. 반면에 새롭게 고안된 멀티접촉패킹에서는 3.01MPa이 발생하여 20.4%나 높아진 밀봉성이 향상되었음을 알 수 있다. 또한, 밀봉내구 안전성에 밀접한 관련이 있는 압출현상은 기존 오링의 경우 1.62MPa의 가스압력에서 발생되었지만, 멀티접촉패킹에서는 1.8MPa 정도로 가스내압을 올려도 압출현상이 발생되지 않는 것은 오랫동안 밀봉작용을 한다는 것을 의미한다. 따라서 밀봉성과 내구안전성을 높게 요구할 때는 한곳에서 접촉하는 기존의 오링보다는 여러 곳에서 접촉하는 멀티접촉패킹을 사용하는 것이 유리함을 알 수 있다.

• 한국전기전자재료학회논문지
• /
• 제18권11호
• /
• pp.1019-1023
• /
• 2005

We have examined the electrical and optical characteristics of the plasma display panel produced by vacuum in-line sealing technology. In the MgO layer deposited at room temperature, after sealing at the panel temperature of $430^{\circ}C$, the luminous efficiency decreased compared with that of the panel before sealing. Moreover, firing and sustain voltage of the sealed panel increased compared with that of the panel before sealing. This was resulted from that the MgO protective layer was cracked by the softening of the dielectric layer during the sealing process. In order to avoid the MgO crack during the vacuum in-line sealing, thermally stable MgO layer or lower temperature sealing is required.

• 한국재료학회지
• /
• 제19권11호
• /
• pp.613-618
• /
• 2009

We designed new compositions for lead free and low temperature sealing glass frit of $ZnO-V_2O_5-P_2O_5$ system, which can be used for PDP (Plasma Display Panel) or other electronic devices. The $ZnO-V_2O_5-P_2O_5$ system can be used as a sealing material at temperatures even lower than 430$^{\circ}C$. This system, however, showed lower bonding strength with glass substrate compared to commercialized Pb based sealing materials. So, we added $TiO_2$ as a promoter for bonding strength. We examined the effect of $TiO_2$ addition on sealing behaviors of $ZnO-V_2O_5-P_2O_5$ glasses with the data for flow button, wetting angle, temporary & permanent residual stress of glass substrate, EPMA analysis of interface between sealing materials and glass substrate, and bonding strength. As a result, sealing characteristics of $ZnO-V_2O_5-P_2O_5$ system glasses were improved with $TiO_2$ addition, but showed a maximum value at 5 mol% $TiO_2$ addition. The reason for improved bonding characteristics was considered to be the chemical interaction between glass substrate and sealing glass, and structural densification of sealing glass itself.

• 한국세라믹학회지
• /
• 제18권2호
• /
• pp.99-104
• /
• 1981

Glass-ceramics possessed a number of characteristics which suggested their suggested their use for sealing to metals. The choice of particular glass-ceramics compositions for this application is governed by various factors, including workability of the glasses, thermal expansion characteristics and the matching of these to appropriate metals. Other properties, such as mechanical strength, determined the performance of glass-ceramics to metal seals. The purpose of the present study was to investigate direct sealing behaviour of copper to $Li_2O-ZnO-SiO_2$ system glass-ceramics. The design of the seal was a concentric seal which might contribute to the strong bond formation by providing compressive stress during thermal excursions. Tensile strengths of sealing layers were measured by Instron test machine. The layers were examined by electron probe microanalyzer. Crsystallization rate was increased with the amount of ZnO or $Li_2O$, and ZnO increased the sealing strength, but $Li_2O$ lowered it. Sealing mechanism was due to the formation of metal oxides, which acted as binder between copper and glass-ceramics. The nickle-plated copper seal with 10% $Li_2O$ and 30% ZnO was the most strong seal, and its sealing strength was more than 56kg/$\textrm{cm}^2$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.610-614
• /
• 1996

Sealing of lubricat-air mixture in the high performance machining conte is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry, Velocity, pressure, turbulence intensity of profile is calculated to fina more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic, This paper arranges a geometry of mostly used non-contact type seal and analyzes leakage characteristics to minimize a leakage on the same sealing area.