• The Journal of the Acoustical Society of Korea
• /
• v.18 no.4
• /
• pp.53-59
• /
• 1999

Of various SPUDT SAW filter types, we select the two most common types, DART and EWC/SPUDT, and analyze their performance with the Smith equivalent circuit method. Based on the results for an exemplary case, a usual apodized SAW filter, we investigate the advantage of one type over the other, if any, in a quantitative manner. To compensate for the performance degradation that can happen in the process of the modification of the apodized filer to the SPUDT structure, we apply the triangular weighting technique to wide fingers of the IDT. Further, the variation in performance of the SPUDT structure is investigated in relation to its electrode thickness and the number of fingers. The results in this paper are expected to enable us to easily select an SPUDT type appropriate for each particular application field.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.41-49
• /
• 1994

This study is to compare the welding quality of API 5L-X65 Steel- pipe's for natural gas transmission piping applied by SAW at shop and by GTAW-SMAW at site. The results can be summarized as follows; 1) Tensile strength of the welded zone by SAW(611.5 MPa) and by GTAW-SMAW(608.6 MPa) was maintained greater than that of the base metal(583.5 MPa). 2) Hardness of the welded zone and HAZ by SAW(Hv 194.8) & GTAW-SMAW (Hv 196.1) was slightly increased above that of the base metal (Hv 168.8), but less than the maximum allowable hardness(Hv 248). 3) Impact value of the welded zone by SAW(126.8 J) & GTAW-SMAW(88 J) became lower than that of the base metal(282.5 J), but was above the requirement of API 5L(68J). 4) Microscopic structure of the welded zone and HAZ by both SAW & GTAW-SMAW became fine-grained.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.5
• /
• pp.400-410
• /
• 1988

In this paper, a fast synchronization system using SAW TDL matched filter and SAW recirculation loop not only for acquisition but also tracking in the direct sequence spread spectrum communication receiver in case of low SNR was designed and its characteristics were investigated. When signal of 16dB SNR was inputed at the receiver, the PN code of the receiver could be synchronized from the extracted signal for synchronization through SAW TDL matched filter and SAM recirculation loop for 30 recirculations. And the average synchronization time of this system was calculated. From the results, we found that this synchronization system could achieve faster synchronization of PN codes in the receiver under the circumstances of low SNR than that of using only matched filter.

• Korean Journal of Food Science and Technology
• /
• v.35 no.5
• /
• pp.994-997
• /
• 2003

Domestic and imported Cnidium officinale were investigated using GC based on a SAW sensor. Volatile components from the herb were detected by GC with a Surface Acoustic Wave (SAW sensor without any pretreatment. This system produced a frequency proportional to the amount of column effluent deposited on the SAW sensor. It could discriminate between domestic and imported Cnidium officinales. This was achieved by using a pattern recognition and a visual pattern called a $VaporPrint^{TM}$, derived from the frequency and chromatogram of the GC-SAW sensor. The origins of Cnidium officinale was well discriminated with the direct use of $VaporPrint^{TM}$.

• Journal of Sensor Science and Technology
• /
• v.33 no.5
• /
• pp.353-358
• /
• 2024

Al-Ni thin films were fabricated using combinatorial sputtering system to realize highly sensitive surface acoustic wave (SAW) devices. The Al-Ni sample library was grown with various chemical compositions and electrical resistivities, which provided important information for selecting the most suitable materials for SAW devices. As acoustic waves generated from piezoelectric materials are significantly affected by the resistivity and density of the interdigital transducer (IDT) electrodes, three types of Al-Ni thin films with different Al contents were fabricated. The thickness of the Al-Ni thin film used in the SAW-IDT electrode was fixed at 100 nm. As the Al content of the Al-Ni film decreased from 79.2 to 24.5 at%, the resistivity increased slightly from 4.8 to 5.8 × 10^-5 Ω-cm, whereas the calculated density increased significantly from 3.6 to 6.9 g/cm³. The SAW device composed of Al-Ni IDT electrodes resonated at 71 MHz without frequency shifts; however, the selectivity of the resonant frequency and insertion loss deteriorated as the Al content decreased. When there is no significant difference in the electrical characteristics of the SAW-IDT electrodes, the performance of the SAW devices can be determined by the density of the IDT electrodes.

• Journal of electromagnetic engineering and science
• /
• v.6 no.2
• /
• pp.110-116
• /
• 2006

A reflective array type surface acoustic wave(SAW) dispersive delay line(DDL) with high time-bandwidth at the V/UHF-band is designed and fabricated for compressive receiver applications. This type of the SAW DDL has the properties of the relative bandwidth of 20 %, the time delay of 49.89 usec, the insertion loss of 38.5 dB and the side lobe rejection of 39 dB. In comparison with a commercial SAW DDL, the insertion loss, amplitude ripple and side lobe rejection are improved by $1.5dB{\pm}0.6dB$ and 4 dB respectively. Using the fabricated SAW DDL, the prototype of the compressive receiver is developed. It is composed of RF converter, fast tunable LO, chirp LO, A/D converter, signal processing unit and control unit. This prototype system shows a fine frequency resolution of below 30 kHz with high scan rate.

• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.249-255
• /
• 2011

Recently the demand for a fast and precise actuator in semiconductor industries is growing larger. A SAW motor is now expected as a new friction-drive actuator to meet such demand. However, its friction and wear properties are almost unknown and its low stability and reliability still remain to be solved. In this research the tests of SAW motor were carried out and its durability was discussed. The effect of wear caused by friction on the driving force and driving speed were clarified.

• Journal of electromagnetic engineering and science
• /
• v.7 no.1
• /
• pp.12-16
• /
• 2007

A UHF band wireless identification system based on passive surface acoustic wave(SAW) devices is presented in this paper. SAW ID tags were fabricated on Y-Z $LiNbO_3$ piezoelectric substrate with a good electro-mechanical coupling property. To reduce degradation of the antenna performance associated with the piezoelectric materials, an efficient design of the SAW RFID antenna is introduced. By measuring the parameters of the SAW ID tag, the performance of the antenna was tested by experimentation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.368-371
• /
• 2008

Cellulose based Electroactive Paper (EAPap) has been developed as a new smart material due to its advantages of piezoelectricity, large displacement, low power consumption, low cost and flexibility. EAPap can be used fur a surface acoustic wave (SAW) device using the piezoelectric property of EAPap, resulting in the cost effective and flexible SAW device. In this paper, inter digit transducer (IDT) structure using lift-off technique with a finger gap of $10{\mu}m$ was used for micro fabrication of the cellulose EAPap SAW devices. The performance of IDT patterned SAW device was characterized by a Network Analyzer. The feasibility of cellulose EAPap as a potential acoustic device was presented and explained.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.228-233
• /
• 2007

An experimental and numerical approach has been carried out to characterize the noise and the safety of circular diamond saw with chinks by laser-cutting. The sound pressure level of a circular diamond saw with chinks was measured when cutting workpieces. Therefore, frequency analysis results show us that the sound level was reduced as position of chinks approach to out-diameter. But the safety of circular diamond saw was lower due to the stress concentrated at the edge of chinks while cutting workpieces. FEM analysis was used for safety evaluation with the variation position of chinks. The noise characteristics of circular diamond saw were also estimated during cutting test.