• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.46-54
• /
• 1996

This study was carried out to investigate the vacuum drying characteristics of 50mm- and 75mm- thick tree disks of some domestic softwoods for substituting the conventional hardwoods as the materials for wood crafts. Though the elapsed drying times from green to in-use moisture content(MC) were largely shortened by vacuum drying, the tree disks treated by EWS couldn't be dried to in-use MC, and so sapwood stains also were occurred severely. We suggest EWS treatment is undesirable for the species with very high sapwood portion or vacuum drying with hot water circulation heating system. Heart checks were slight, but sapwood checks, which have never been trouble in drying process of tree disks, were severe. For the reasonable explanation it is suggested MC differences between sapwood and heartwood were large and most of tree disks had already no barks before drying test. Ginkgo was vacuum-dried with very slight drying defects such as heart checks, sapwood checks. V-cracks and sapwood stains. In Korean red pine and pitch pine V-cracks were severely occurred. And it was found the special feature that most of these defected tree disks contained several V-cracks within one tree disk. It can be considered as the causes that the region of sapwood was defected by the several checks at the early drying stage because of the steep MC gradient along the radial direction, and then at the later drying stage the drying stresses due to differential shrinkage were concentrated on these brittle spots.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.52-60
• /
• 2006

This study investigated how wood properties (i.e., annual rings, sapwood, heartwood, and cracks) might affect preservative treatment in Japanese larch (Larix leptolepis) round-wood product. We specially focused on small-diameter (~10 cm diameter) wood that is commercially sold in market. Among 100 wood samples, the groups of sample with 13~16, 17~20 annual rings represented 33 and 27 in each frequency, while 2~3 and 4~5 mm annual ring width accounted for 72 and 68 in frequency. More than a half (54%) of wood samples contained a mix of heartwood and sapwood in its surface. The rest (46%) had only heartwood exposed in the wood surface. A wide range of checks were showed in the wood samples, but the highest frequency was observed in samples with 1~6 surface (1~14 mm in size) checks and 1~4 end-grain (8~14 mm in size) checks in each round-wood sample. Pressure treatment resulted in a wide range of penetration of ACQ (Alkaline Copper Quat) into the wood, showing $4.3{\pm}4.19mm$ penetration in the wood samples contained a mix of heartwood and sapwood in its surface. However preservative treatment was much less effective for the heartwood only wood samples, ranging average 1.3 mm with ACQ and 1.1 mm with CCA (Chromated Copper Arsenate). These penetration results shown in heartwood samples did not meet the penetration standard that is required for H3 by the Korean Forest Service in relation to wood preservation treatment. These low penetration results were not significantly improved even if we incised wood samples to improve treatment effect, showing only small increase of 0.7 mm with ACQ and 0.6 mm with CCA. When preservative treatment was tested with heartwood, penetration of preservatives decrease with increase of annual rings per a cross-section area (r=0.5345). We also found that the length and number of check had no effect on preservative treatment, showing r=0.1301 and r=0.1802, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.27-32
• /
• 2002

We investigated the effect of polyethylene glycol(PEG) treatment of preservative treated green japanese cedar(Cryptomeria japonica) round posts on their preservative penetration and check formation during the air drying. The round rods were dip-treated in 10% preservative solution of Basilit CFK for 1 day, followed by application(3, 5, and 10 times) with 50% PEG-400 solution, and then dried for 30 days under natural conditions. The rate of preservative penetration into sapwood was a low by 23.2% without PEG treatment, whereas that was a high by about 51.2~64.5% with PEG treatment. From these results, it was assumed that PEG played an affirmative role in the penetration of preservative components loaded onto the surface of round rods by dipping. During the air drying, the formation of drying checks decreased significantly with increasing application times of PEG. Even though some drying checks in PEG treated rods were developed, the number and size of checks was reduced remarkably by PEG treatment. After 2 months of outdoor exposure, PEG treatment failed to reduce checking in preservative-treated rods whereas finishing of polyurethane resin lacquer after PEG treatment was significantly effective in preventing check development.