• 한국지반공학회논문집
• /
• 제15권3호
• /
• pp.113-129
• /
• 1999

본 연구에서는 사질토 지반에서의 굴착단계별 연성 벽체의 거동분석을 수행하기 위해 흙막이벽의 모형실험을 실시하였다. 모형 흙막이벽 실험에서는 재료의 역학적 특성이 비교적 널리 알려진 주문진 표준사를 이용하여 상대밀도가 79%, 41%, 24%인 모형지반을 조성한 후 모형벽체의 연성지수를 변화시켜 각 굴착단계별로 배면지반과 연성 벽체의 거동특성을 규명하였다. 본 연구에서는 벽체의 수평변위, 벽체의 배면에 작용하는 수평토압, 굴착으로 인한 배면지반의 침하량 및 침하영향거리, 벽체에 작용하는 앵커의 하중, 그리고 벽체에 작용하는 휨모멘트와 축력에 대해 굴착단계에 따라 살펴보고 이를 토대로 지반과 벽체의 거동특성을 분석하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1182-1189
• /
• 2010

The mechanical behavior of a granular material is governed by the applying effective stresses and its skeletal structure which is considered to be the packing of particles giving overall density and degree of anisotropic. Factors that affect soil packing are the particle size, size distribution and shape, and the arrangement of grain contact. Soil particle size and shape are the most important factor, but difficult to quantify. In this study, 2D Fourier analysis is applied to quantify the shape of granular particles. Jumunjin sand was used in the experiment and particle images are captured using an optical microscope. The results showed that three lower order Fourier descriptor are closely related with roundness, sphericity of the granular particle. Also statistical approach is used to determine roundness, form factor, elongation ratio, roughness of Jumunjin sand.

• 한국농공학회지
• /
• 제40권6호
• /
• pp.95-103
• /
• 1998

Solutions of geotechnical engineering problems require calculation of deformation and stresses during various stages of loading. Powerful numerical methods are available to make such calculation even for complicated problems. To get accurate results, realistic stress-strain relationships of soil are dependent on a number of factors such as soil type, density, stress level and stress path. Attempts are continuously being made to develope analytical models for soils incorporating all such factors. The nature of stress-path dependency, the principle that governs deformations in sand, and the use of Lade's single work-hardening model for predicting sand response for a variety of stress-paths have been investigated and are examined. The test results and the analyses presented show that under some conditions sand exhibits stress-path dependent behavior. The strains calculated from Lade's single work-hardening model are in reasonable agreement with those measured, but some discrepancies occur. The largest difference between measured and calculated strains occurs for proportional loading with increasing stresses and for stress-path directions.

• 설비공학논문집
• /
• 제20권9호
• /
• pp.614-623
• /
• 2008

This paper presents the results of a laboratory study on the thermal conductivity of and(silica, quartzite, limestone, sandstone, granite and two masonry sands)-water mixtures used for ground heat exchanger backfilling materials. Nearly 260 tests were performed in a thermal conductivity measuring system to characterize the relationships between the thermal conductivity of mixtures and the water content. The experimental results show hat the thermal conductivity of mixtures increases with increasing dry density and with increasing water content. The most widely used empirical prediction models for thermal conductivity of soils were found inappropriate to estimate the thermal conductivity of unsaturated sand-water mixtures. An improved model using an exponential relationship to compute the thermal conductivity of dry sands and empirical relationship to assess the normalized thermal conductivity of unsaturated sand-water mixtures is presented.

• Geomechanics and Engineering
• /
• 제11권5호
• /
• pp.691-711
• /
• 2016

In this study, the uplift capacity of anchor plates embedded in sand was investigated by conducting model tests. Square shaped anchors were used in the tests and parameters such as relative density of sand, embedment ratio (H/B), spacing ratio between anchors (S/B) and anchor configuration affecting the uplift capacity were investigated. Breakout factor and group efficiency which are dimensionless parameters were used to show the results. A series of finite element analyses and analytical solutions were additionally performed to ascertain the validity of the findings from the laboratory model tests and to supplement the results of the model tests. It can be concluded that the embedment depth in dense sand soil condition is the most important parameter with respect to the other parameters as to influencing the uplift capacity of group anchors.

• Geomechanics and Engineering
• /
• 제4권2호
• /
• pp.91-103
• /
• 2012

Focusing on the effect of excess pore pressure dissipation on liquefaction-induced ground deformation, a series of 1-g shaking table tests were conducted in a rigid soil container by use of saturated Toyoura sand, the relative density of which was 20-60%. These tests were subjected to the sinusoidal base shaking with step increased accelerations: 100, 200, 300 and 400 Gals for 2-4 seconds. Shaking table tests were done using either water or polymer fluid with more viscous than water, thus varying the sand permeability of model tests. Excess pore pressures, accelerations, settlements and lateral deformations were measured in each test. Test results are presented in this paper and the effect of sand permeability on liquefaction and liquefaction-induced ground deformation was discussed in detail.

• 한국지반공학회지:지반
• /
• 제10권4호
• /
• pp.119-132
• /
• 1994

본 연구에서는 실트를 포함하는 모래의 액상화강도 및 전단특성을 검토하기 위하여 비배수상태에서 동적 삼축압축시험을 행했다. 그 결과 실트를 포함하는 모래의 액상화강도는 상대밀도 일정의 조건에서는 실트 함유율 30% 정도에서 가장 약한 것으로 판명되었다. 또한 동적 삼축압 축시험의 재하속도를 0.1Hz에서 5Hz까지 변화시켜 실트를 포함하는 모래질 흙의 액상화강도에 미치는 제하속도의 영향을 살펴본 결과 실트의 함유량이 많을수록 재하속도의 영향을 많이 받으나 점토를 함유한 모래질 흙에 비해서는 그 영향이 현저하게 적음을 알 수 있다. 이러한 결과의 일인에 대해서는 유효응력 경로에 있어서의 간극수압의 변화상황으로부터 설명될 수 있다.

• Geomechanics and Engineering
• /
• 제8권1호
• /
• pp.1-15
• /
• 2015

This paper presents a series of conventional undrained triaxial compression tests conducted to determine the effect of both tire crumbs and cement addition on Narli sand specimens. The tire crumb contents and cement contents were 3%, 7%, 15%; and 1%, 3%, 5% by dry weight of the sand specimens respectively. Specimens were prepared at about 35% relative density, cured during overnight (about 17 hours) for artificially bonding under a 100 kPa effective stress (confining pressure of 500 kPa with a back pressure of 400 kPa), and then sheared. Deviatoric stress-axial strain, pore water pressure-axial strain behavior, and Young's modulus of the specimens at various mixture ratios of tire crumb/cement/sand were measured. Test results indicated that the addition of tire crumb to sand decreases Young's modulus, deviatoric stress and brittleness, and increase pore water pressure generation. The addition of cement to sand with tire crumbs increases deviatoric stress, Young's modulus, and changes its ductile behavior to a more brittle one. The results suggest that specimen formation in the way used here could reduce the tire disposal problem in not only economically, and environmentally, but also more effectively beneficial way for some geotechnical applications.

• 상하수도학회지
• /
• 제31권6호
• /
• pp.521-527
• /
• 2017

Phosphorus is one of the limiting nutrients for the growth of phytoplankton and algae and is therefore one of leading causes of eutrophication. Most phosphorous in water is present in the form of phosphates. Different technologies have been applied for phosphate removal from wastewater, such as physical, chemical precipitation by using ferric, calcium or aluminum salts, biological, and adsorption. Adsorption is one of efficient method to remove phosphates in wastewater. To find the optimal media for phosphate removal, physical characteristics of media was analysed, and the phosphate removal efficiency of media (silica sand, slag, zeolite, activated carbon) was also investigated in this study. Silica sand showed highest relative density and wear rate, and phosphate removal efficiency. Silica sand removed about 36% of phosphate. To improve the phosphate removal efficiency of silica sand, Fe coating was conducted. Fe coated silica sand showed 3 times higher removal efficiency than non-coated one.

• 한국지반공학회지:지반
• /
• 제8권4호
• /
• pp.67-80
• /
• 1992

동적인 문제를 해석하는 데 있어서 최대전단탄성계수의 결정은 어떤 변형률에서의 전단응력을 추정하는데 필연적이라 할 수 있다. 그동안 실리카질 모래에 관한 모델이 준시되어 왔지만 그러한 모델을 부서지는 모래에 직점적으로 적용하는 데는 모래의 부서짐(crushability)때문에 어려움이 있다. 본 연구에서는 부서지는 모래의 미소변형률에서의 동적인 거동이 평가되었으며 실험한 모래의 최대 전단탄성 계수에 관한 모델이 제시되었다. 부서지는 모래의 전단탄성 계수는 느슨한 모래의 경우는 실리카질 모래와 유사한 값을 보이나 밀도가 증가하면 입자간의 접촉면적이 커져서 비틀력 (torsional force)으로 인해 모래가 부서져 전단저항이 작아지는 것으로 보인다. 그리고 계수치 (modulus number) 가 Been과 Jefferies (1985)의 상태 정수 (state parameter)로 표현되었다.