• Membrane and Water Treatment
• /
• 제13권4호
• /
• pp.191-199
• /
• 2022

In industrial production, the development of traditional polyamide nanofiltration (NF) membrane was limited due to its poor oxidation resistance, complex preparation process and high cost. In this study, a composite NF membrane with high flux, high separation performance, high oxidation resistance and simple process preparation was prepared by the method of dilute solution dip coating. And the sulfonated polysulfone was used for dip coating. The results indicated that the concentration of glycerin, the pore size of the based membrane, the composition of the coating solution, and the post-treatment process had important effects on the structure and performance of the composite NF membrane. The composite NF membrane prepared without glycerol protecting based membrane had a low flux, when the concentration of glycerin increased from 5% to 15%, the pure water flux of the composite NF membrane increased from 46.4 LMH to 108.2 LMH, and the salt rejection rate did not change much. By optimizing the coating system, the rejection rate of Na₂SO₄ and PEG1000 was higher than 90%, the pure water flux was higher than 40 LMH (60psi), and it can withstand 20,000 ppm.h NaClO solution cleaning. When the post treatment processes was adjusted, the salt rejection rate of NaCl solution (250 ppm) reached 45.5%, and the flux reached 62.2 LMH.

• 한국재료학회지
• /
• 제32권10호
• /
• pp.442-447
• /
• 2022

Sealing treatment is a post-surface treatment of the plasma spray coating process to improve the corrosion resistance of the coating material. In this study, the effect of the sealing on the corrosion resistance and adhesive strength of the plasma spray-coated alumina coatings was analyzed. For sealing, an epoxy resin was applied to the surface of the coated specimen using a brush. The coated specimen was subjected to a salt spray test for up to 48 hours and microstructural analysis revealed that corrosion in the coating layer/base material interface was suppressed due to the resin sealing. Measurement of the adhesive strength of the specimens subjected to the salt spray test indicated that the adhesive strength of the sealed specimens remained higher than that of the unsealed specimens. In conclusion, the resin sealing treatment for the plasma spray-coated alumina coatings is an effective method for suppressing corrosion in the coating layer/base material interface and maintaining high adhesive strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.697-700
• /
• 2008

본 연구에서는 고로슬래그 혼합시멘트와 3성분계 저발열 혼합시멘트를 대상으로 하고, 여기에 CSA계 팽창재를 혼입함으로서 이에 따른 수축보상 효과와 함께 염해저항 특성에 미치는 영향에 대하여 검토하였다. 검토결과, 배합조건이 OPC이고, 팽창재 혼입율이 8%인 경우는 팽창재를 혼입하지 않은 경우에 비해 최대 43.7배까지팽창하는 것으로 평가되었고, 굵은골재 최대치수가 콘크리트의 길이변화특성에 미치는 영향은 적은 것으로 나타났다. 염해저항성은 굵은골재 최대치수가 클수록, 그리고 팽창재 혼입율이 증가할수록 개선되는 것으로 평가되었는데, 본 연구범위에서는 팽창재를 8% 혼입한 콘크리트의 염해저항성이 팽창재를 혼입하지 않은 경우에 비해 약 16% 정도 유리한 것으로 평가되었다.

• 한국수소및신에너지학회논문집
• /
• 제23권6호
• /
• pp.573-580
• /
• 2012

Corrosion resistance and basic physical properties of solid tantalum are not comparable to most of the structural metallic materials. The relative high cost and melting temperature of tantalum are obstacles to be widely applied to general engineering processes. Electrodeposition in molten salt enables compact and uniform tantalum coating. In this study, Ta was coated onto base metal (SUS316L) with different current densities (0.5, 5, $20mA/cm^2$) by using MSE (Molten Salt Electrodeposition). In this study, it showed that deposition efficiency and microstructure of Ta coating layer were strongly depended on current density. In the case of the current density of $5mA/cm^2$, densest microstructure was obtained. The current density above $5mA/cm^2$ caused non-uniform microstructure due to rapid deposition rate. Dense microstructure and intact coating layer contributed to significant corrosion resistance enhancement.

• 한국재료학회지
• /
• 제7권1호
• /
• pp.76-80
• /
• 1997

용융탄산염 연료전지 분리판의 wet-seal부의 내식성 향상을 위한 NiAl 피복공정이 조사되었다. AlSl 316 스테인레스강위에 Ni과 Al를 순차적으로 피복한 후, $800^{\circ}C$에서 3시간 열처리하여 NiAl상이 형성됨을 확인할 수 있었다. NiAl상이 피복된 스테인레스강은 $650^{\circ}C$, 용융탄산염($62^{m}/_{o}Li_2CO_3-38^{m}/_{o}/K_{2}CO_{3}$)내에서 침지시험을 통해 내식성이 평가되었는데, AISI 316 스테인레스강에 비해 우수한 내식성을 보였다. 이는 표면에 치밀하게 형성된 AI 산화물층에 의한 것으로 판단되었다.

• 패션비즈니스
• /
• 제9권2호
• /
• pp.71-83
• /
• 2005

In this study, we reviewed the color changes accompanying the laundering, wash fastness, and abrasion fastness of chitosan-treated cochineal-dyed fabrics. The treatment methods were classified into two based on the chitosan treatment: (Method 1): fabric specimens were pre-treated with chitosan prior to the dyeing procedure in salt form. (Method 2): the state of chitosan acid salt formation, coated on the yarn surface, was destroyed and neutralized prior to the dyeing process. The changes in the chitosan treatment methods bear more important meaning in view of the durability. In Method 1, it is highly likely for the chitosan to be detached from the surface by water during laundering since the chitosan is coated as acid salt state. In Method 2, the resistance d the chitosan to water was supposed to revive since the chitosan would return to its original state. Differences in the resistance of the chitosan treatrrent, however, according to the Method 1 and Method 2, fell short of our expectations. In Method 2, the wash fastness did not improve as we expected since the bond between the fibers comprising fabric specimens and the chitosan is not high even if the chitosan itself has high resistance to water.

• 한국건축시공학회지
• /
• 제22권5호
• /
• pp.425-430
• /
• 2022

초고층 건축물용 매트기초에 사용되는 콘크리트는 시공성 및 품질확보를 위하여 일체타설로 진행되는 경우가 많다. 하지만 일체타설의 경우 수화반응 과정에서 온도균열이 발행할 우려가 높으며 혼화재 치환을 통해 고성능 고내구성 콘크리트 최적배합을 도출할 필요가 있다. 본 연구에서는 저자의 기존연구에서 도출한 최적 고성능 저발열 콘크리트 배합으로 제작된 시험체를 대상으로 염해 및 탄산화, 내황산염에 대한 실험을 실시하고 염소이온 확산계수와 탄산화계수, 황산염에 대한 시멘트 매트릭스의 저항을 정량적으로 평가하였다. 혼화재의 혼입에 의한 잠재수경성 및 포졸란 반응에 의한 높은 저항성을 확인할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2004년도 학술대회지
• /
• pp.33-38
• /
• 2004

This study was performed to know watertightness and reduction effect and crack occurred by hydration heat, restraint of multiplication of hydration heat, through mechanical test, strength test and crack control test using fluosilicate salt based inorganic compound made from by-product during phosphoric acid manufacturing process. Mix proportions for experiment were modulated at 0.45 of water to cement ratio and $0.5-2.0\%$ of adding ratio of fluosilicate salt based inorganic compound. Evaluation for watertightness of concrete was carried out permeability, absorption test and porosity analysis. Effect of crack reduction was evaluated by length, drying shrinkage as well as stress change of hardened concrete at unrestraint/restraint state and also elucidated crack pattern on the concrete surface. It is ascertained that characteristics of crack resistance and watertightness for concrete was improved by an adequate addition of fluosilicate salt based inorganic compound.

• Corrosion Science and Technology
• /
• 제8권4호
• /
• pp.157-161
• /
• 2009

The corrosion resistance of reinforcing bar was studied to endure the marine environment during shipment. The red rust on the surface did not damage the adherence in the concrete structures, especially in highly alkaline environment, but made the consumer doubt of the quality. The passivation process by alkalization of the quenching water in the tempcore process failed to endure the long shipping period. The ceramic coating by sol-gel process improved the corrosion resistance without damaging the mechanical properties and adherence between concrete and reinfiorcing bar. Optimal concentration of the coating solution and coating temperature were tested. No additional energy was necessary for the coating process by spraying during cooling process, resulting simplified process and low cost. Salt spray test, cyclic corrosion test and atmospheric test were employed to confirm the resistance. The corrosion rates were presented by rating number and polarization resistance. The coating layer was examined by FIB, XRD and SEM etc.

• 방사성폐기물학회지
• /
• 제14권3호
• /
• pp.211-221
• /
• 2016

파이로 공정에서 발생되는 염폐기물은 휘발성이 높아 고온공정에 적용하기 어려우며, 폐기물내에 존재하는 염소로 인해, 전통적인 유리매질에 대한 상용성이 낮은 특성을 가지고 있어, 새로운 고화방법이 필요하다. KAERI에서는 탈염소화법을 이용하여 염소를 탈리하고, 일반적인 유리매질에 고화하는 연구방법을 제안하였다. 본 연구에서는 기존의 탈염소화법에 사용된 합성무기복합체(SAP, $SiO_2-Al_2O_3-P_2O_5$)에 첨가물로서, $Fe_2O_3$ 및 $B_2O_3$를 부가하여 5성분계의 복합체를 제조하고, 조성에 따른 탈염소화반응 및 고화체의 특성을 조사하였다. 탈염소화 반응은 조성에 따른 생성물의 변화 경향은 크지 않았으며, 유사한 반응메커니즘으로 주어진 시간 내에 반응이 진행되는 것으로 나타났다. Si-rich phase와 P-rich phase를 화학적으로 연결시켜주는 $Al_2O_3$와 $B_2O_3$의 함량이 높은 경우에는 고화체내 상분리의 정도는 상대적으로 낮게 나타나며, 구성원소의 분포가 보다 균일한 형태를 보였다. PCT-A 침출시험법을 통한 조성에 따른 내구성의 평가결과, 기준조성을 벗어나는 경우에는 내침출성이 낮게 나타났으나, EA glass(Environmental Assessment glass)의 값보다는 우수한 것으로 확인되었다. 이상의 결과로 부터, 주어진 적정 Si와 P의 조성분율하에서, Al과 B의 함량변화는 고화체의 미세구조와 내침출성에 영향을 주는 것을 확인할 수 있었으며, 미세구조와 내침출성의 연관관계에 대한 추가적인 연구가 필요할 것으로 판단된다.