• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.513-520
• /
• 2003

A numerical comparison or predictions by limit equilibrium analysis and 3n analysis is presented for slope/pile system. Special attention is given to the coupled analysis based on the explicit-finite-difference code, FLAC. To this end, an internal routine (FISH) was developed to calculate a factor of safety for a pile-reinforced slope according to shear strength reduction technique. The case of coupled analyses was performed for stabilizing piles in slope in which the pile response and slope stability are considered simultaneously and subsequently the factors of safety are compared to uncoupled analysis (limit equilibrium analysis) solution for a homogeneous slope. Based on a limited parametric study, it is shown that in the free-head condition the factor of safety in slope is more conservative for a coupled analysis than for an uncoupled analysis and a definitely larger value represents when piles are installed in the middle of the slopes and are restrained in the pile head.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.643-650
• /
• 2002

The large planar failure has occurred in a rock cut slope of highway construction site in Boeun. This area is considered as unstable since the discontinuities whose orientations are similar to the orientation of the failure plane, are observed in many areas. Therefore, several analysis techniques such as SMR, stereographic analysis, limit equilibrium, numerical analysis, which are commonly used in rock slope stability analysis, are adopted in this area. In order to analyze the stress redistribution and nonlinear displacement caused by cut, which are not obtained in limit equilibrium method, the UDEC and shear strength reduction technique were used in this study Then the factors of safety evaluated by shear strength reduction technique and limit equilibrium were compared. In addition, the factor of safety under fully saturated slope condition was calculated and subsequently, the effect of the reinforcement was evaluated.

• Geomechanics and Engineering
• /
• v.28 no.1
• /
• pp.77-87
• /
• 2022

Many geotechnical analyses require the investigation of water flow within partially saturated soil zone to incorporate the effect of climatic conditions. It is widely understood that the hydraulic properties of the partially saturated soil should be included in the transient seepage analyses. However, the characteristics of dual porosity soils with dual-mode water retention curve are normally modelled using single-mode mathematical equation for simplification of the analysis. In reality, the rainwater flow can be affected significantly by the dual-mode hydraulic properties of the soil. This paper presents the variations of safety factor for dual porosity soil slope with dual-mode water retention curve and dual-mode unsaturated permeability. This paper includes the development of the new dual-mode unsaturated permeability to represent the characteristics of soil with the dual-mode water retention curve. The finite element analyses were conducted to examine the role of dual-mode water retention curve and dual-mode unsaturated permeability on the variations of safety factor under rainfall loading. The results indicate that the safety factor variations of dual porosity soil slope modelled using the dual-mode water retention curve and the unsaturated permeability equation are lower than those of dual porosity slope modelled using single-mode water retention curve and unsaturated permeability equations.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.5-16
• /
• 2008

Field monitoring data of nine sites were investigated to suggest an evaluation method on lateral movement of the quaywall on soft grounds. It was found that in order to evaluate the lateral movement of quaywalls with foundation piles such as the landing pier, the safety factor of slope should be applied with consideration of the stabilizing effect of the piles. If the required safety factor of slope is greater than 1.6 in slope stability analysis with consideration of the stabilizing effect of the piles, the quaywalls are considered to be safe against lateral movement. On the other hand, for the gravity-type quaywalls such as the caisson type quaywall, the required safety factor of slope should be greater than 1.3.

• Journal of the Korean Professional Engineers Association
• /
• v.16 no.2
• /
• pp.11-17
• /
• 1983

This work presents a method for the determination of the safety factor of a slope based on the theory of the calculus of variations. The method allows for the determination of the critical sliding line (The one giving the minimum safety factor) without the necessity of guessing about its shape, which leads to a considerable economy of time and effort. Furthermore it gives the actual safety factor of the slape and consequently a more complete knowledge of the safety of the slope is obtained.

• Korean Journal of Agricultural Science
• /
• v.39 no.1
• /
• pp.97-110
• /
• 2012

This study was carried out for safety evaluation, the practical application and improvement of design method of the agricultural reservoir embankment according to backside extension. Seepage analysis, slope stability analysis and finite element analysis were performed for steady state and transient conditions. Also, the pore water pressure, seepage quantity, safety factor and stress-strain behavior according to high water level and rapid drawdown were compared and analyzed. The pore water pressure at contact region between backside extension and old embankment was kept high after rapid drawdown. Therefore, backside extension is recommended that design method is required to be improved and reinforced more than the others raising embankment. The hydraulic gradients before and after backside extension showed high value at the base of the core, but they showed stable state at the upstream slope and downstream slope. The seepage quantity per 1 day and the leakage per 100 m for the steady state and transient conditions appeared to be safe against the piping. The safety factor of slope stability showed high at the steady state, and transient conditions did not show differences depending on the rapid drawdown. The safety factor was appeared high at the upstream slope before backside extension and downstream slope after extension. The excess pore water pressure for steady state and transient conditions showed negative(-) at the upstream slope, it was small at the downstream slope. The mean effective stress (p') showed high at the base of the core and to be wild distribution after the extension. The displacement after extension showed 0.02-0.06 m in the upstream slope, the maximum shear strain after extension was smaller than that before extension.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.777-780
• /
• 2005

The bench of cut-slope is necessary to stabilizing. But it is possible to be a weak zone in slope. When a small scale failure is occurred in a bench, it influence a large scale failure of slope. So when it is found out any unstable factor, weathering of rock, a direction of joint in a bench, if the bench is reinforced suitably, the holly failure is prevented in cut-slope

• Journal of the Korean Geotechnical Society
• /
• v.31 no.1
• /
• pp.47-52
• /
• 2015

In the slope stability analysis and design, Limit Equilibrium Method (LEM) and Shear Strength Reduction technique (SSR) are mainly used. Both methods are able to perform two and three dimensional analysis. SSR is considered to be more sensitive and more reasonable than LEM by many researchers. However, in practice LEM is still widely used because of the increase of analysis time and complexity of the model in SSR. In this study, three dimensional analysis of the protruding rock slope is performed by SSR in order to study the effects of protruding length using rock slope FLAC 3D. In this study, as results of analysis variations of the safety factor have been studied according to slope angle, slope height, the soil strength, protruding slope length projected variables. The results show that the factor of safety as more affected by the shapes of the protruding rock slope than the rock strength.

• Journal of the Korean Professional Engineers Association
• /
• v.18 no.3
• /
• pp.21-27
• /
• 1985

Earthen mass located beneth a sloping group surface, whether natural or manmade, have a tendency to move downward and outward under the influence of gravity. Unless this tendency is suitably counteracted by the Shearing resistances within the mass, a landslide occurs. Avoiding such instabilities is a major concern of the geotechnical engineer. The shearing behavior of a soil is determined empirically, i.e., by field tests or laboratory tests. This results are applied to the slope stability analysis. The factor of safety for slope stability analysis is much more sensitive to the choice of strength parameters as interpreted from soil tests than to the choice of the computational method of analysis. This paper was investigated the influence of the change in the factor of safety due to a change in one of the parameters, relative to the total change in the factor of safety due to change in all parameters. A conclusion may be reached with respect to the required precision definition of the different variables to limit uncertainties in the factor of safety to tolerable levels.

• Structural Engineering and Mechanics
• /
• v.41 no.3
• /
• pp.339-348
• /
• 2012

The slope stability analysis is usually done using the methods of calculation to rupture. The problem lies in determining the critical failure surface and the corresponding factor of safety (FOS). To evaluate the slope stability by a method of limit equilibrium, there are linear and nonlinear methods. The linear methods are direct methods of calculation of FOS but nonlinear methods require an iterative process. The nonlinear simplified Bishop method's is popular because it can quickly calculate FOS for different slopes. This paper concerns the use of inverse analysis by genetic algorithm (GA) to find out the factor of safety for the slopes using the Bishop simplified method. The analysis is formulated to solve the nonlinear equilibrium equation and find the critical failure surface and the corresponding safety factor. The results obtained by this approach compared with those available in literature illustrate the effectiveness of this inverse method.