• 한국지반공학회논문집
• /
• 제21권1호
• /
• pp.5-14
• /
• 2005

인천국제공항 공사현장의 흙막이 굴착단면에서 계측된 자료를 검토하여 연약지반에 설치된 강널말뚝 흙막이벽의 수평변위와 굴착주변지반의 변형에 대한 상관관계를 조사하였다. 벽체의 지지방식에 따른 강널말뚝 흙막이벽의 수평변위는 앵커지지, 복합지지, 버팀보지지 순으로 작게 나타났으며, 각각의 지지방식에 따른 최대수평변위 발생위치도 서로 다르게 발생하였다. 흙막이벽의 최대수평변위 및 최대수평변위속도는 굴착지반의 안정수가 ${\pi}$이하일 경우 각각 굴착깊이의 $1\%$, 1mm/day이하로 발생되고, 안정수가 ${\pi}+2$ 이하일 경우 각각 굴착깊이의 $2.5\%$, 2mm/day이하로 발생되며, 안정수가 ${\pi}+2$ 이상일 경우 급격하게 증가한다. 또한, 굴착저면에서의 N치가 감소함에 따라 흙막이벽의 최대수평 변위는 증가하며, N치가 약 10이하일 경우 흙막이벽의 최대수평변위는 급격하게 증가함을 알 수 있다. 한편, Terzaghi(1943)에 의해 제안된 히빙에 대한 안전율이 감소함에 따라 흙막이벽의 최대수평변위는 증가하며, 히빙의 안전율이 2.0일 경우 흙막이벽의 최대수평변위는 급속하게 증가함을 알 수 있다. 따라서, 국내 연약지반 강널말뚝 흙막이벽의 경우 히빙에 대한 안전율은 2.0으로 제안할 수 있다.

• 한국전산구조공학회논문집
• /
• 제22권4호
• /
• pp.349-354
• /
• 2009

초고층 건물의 안전성 및 사용성을 합리적으로 확보하고 유지하기 위해서 부재의 구조 반응 모니터링은 필요하다. 이러한 대형 건물의 건전도 모니터링은 최근 들어 많은 연구자들에 의해서 관심 되어지고 있지만 건물 특성상 계측 대상 부재가 많고 하중과 구조반응의 관계가 복잡하기 때문에 센싱 부재 선정의 어려움으로 그 적용에 한계가 있다. 본 논문에서는 부재의 변위기여도 및 변형에너지밀도를 기반으로 초고층 건물의 안전성 모니터링을 위한 구조반응 계측 부재 선정에 대한 연구를 수행하였다.

• 한국지반환경공학회 논문집
• /
• 제25권4호
• /
• pp.29-35
• /
• 2024

본 연구는 강봉앵커의 프리스트레스 도입 전 수동저항 효과를 확인하기 위한 해석적 연구이다. 영구앵커로 강봉을 사용하는 경우 두부 하중 재하 전에도 비탈면 내 변위 발생 시 강봉, 그라우트, 주변 지반사이 상호작용에 따른 수동저항효과로 변위가 억제된다. 이에 실제 강봉앵커가 적용된 현장을 대상으로 한계평형해석 및 유한요소해석을 이용하여 파괴면의 형상 및 안전율 변화를 검토하였다. 검토결과, 강봉앵커가 보강된 비탈면의 안전율은 유한요소해석결과 2.02이며, 한계평형해석결과 2.14에 비해 약 5.9% 작게 발생하였고 활동면의 위치도 더 깊게 발생하였다. 이는 보강 전 비탈면에 비해 안전율이 한계평형해석은 163%, 유한요소법은 153% 증가된 것이다. 또한, 최대발생 변위는 비탈면 내 하부 무보강구간에서 발생하였으며, 강봉앵커가 설치된 위치에서는 변위가 42~83% 감소되는 것으로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권6호통권58호
• /
• pp.183-191
• /
• 2009

본 연구에서는 지진시 nailed-soil 굴착벽체의 안전율과 거동특성에 대하여 제시하였다. 시간이력해석을 이용하여 정적하중과 지진하중을 받는 nailed-soil 굴착벽체 전면부의 수평변위, 축력, 전단력, 모멘트를 해석하였다. Dawson과 Roth가 제안한 전단강도 감소기법에 바탕을 둔 안전율을 지진시 nailed-soil 굴착벽체의 안전율 계산에 사용하였다. 제안된 방법에 의한 안전율을 기존의 연구에서 산정된 안전율과 비교하여 그 타당성을 확인하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권4호
• /
• pp.169-176
• /
• 2001

This study aims to present a more reasonable control value than the exiting one by comparing and analyzing control values and field instrument8tion values of the whole excavation depth of the four case sites, using geometric averaging as a statistical method. The range of the study is confined to the horizontal displacement of braced excavation walls among a variety of items, prescribed in the control values by approximately of the allowable and design values, and by safety factors. As a result, it is desirable to revise 70, 90, and 100 percent of LEVEL I, II, and III, respectively. The horizontal displacement values of the allowable and design values approximations should change to 104, 133, and 148 percent of the allowable and design values, respectively. In addition, modifying the horizontal displacement control value of the braced excavation walls is not needed. The horizontal displacement value, presented in the control value as a safety factor, is now 1.19, as it has a slight difference from the present value.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.534-537
• /
• 2007

The soil nailing was generally using method in practical business, in application of the soil nailing, the analysis was primarily used to Beam-Colum Method, Finite Element Method and Limit Equilibrium Method. Beam-Colum Method and Finite Element Method were able to examine transformation but widely using Limit Equilibrium Method wasn't able to examine transformation and displacement Therefore, this study was focused on presenting stability in comparison with former study-results about horizontal displacement of the soil nailing retaining-walls satisfing a criterion safety factor of Limit Equilibrium. There were performing comparison field measurements and former study-results in first step.

• 농업과학연구
• /
• 제24권2호
• /
• pp.226-236
• /
• 1997

The results obtained by elasto-plastic analysis method about the displacement, deformation and stability on the soft ground excavation using sheet pile were summarized as follows ; 1. In the case of strut 1 step, the maximum wall displacement value in the first and the second excavation was small, but it increase remarkably after the third excavation and when the excavation depth was 8m, the point of maximum wall displacement was shown 0.75H~0.8H. 2. The value of safety factor(Fs) was increased with increasing of the penetration depth of sheet pile, cohesion and internal friction angle of ground. Safety factor was mostly effected by penetration depth of sheet pile and more effected by cohesion than internal friction angle of ground. 3. Since the deformation of sheet pile of this ground from the results of analysis and measurement increased remarkabaly after 6m excavation depth, it was desirable that the point of strut installation was GL-6m. 4. Safe excavation depth on ground by analysis considered penetration depth, cohesion and internal friction was shown at the table 3.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.643-650
• /
• 2002

The large planar failure has occurred in a rock cut slope of highway construction site in Boeun. This area is considered as unstable since the discontinuities whose orientations are similar to the orientation of the failure plane, are observed in many areas. Therefore, several analysis techniques such as SMR, stereographic analysis, limit equilibrium, numerical analysis, which are commonly used in rock slope stability analysis, are adopted in this area. In order to analyze the stress redistribution and nonlinear displacement caused by cut, which are not obtained in limit equilibrium method, the UDEC and shear strength reduction technique were used in this study Then the factors of safety evaluated by shear strength reduction technique and limit equilibrium were compared. In addition, the factor of safety under fully saturated slope condition was calculated and subsequently, the effect of the reinforcement was evaluated.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.139-146
• /
• 2001

The seismic safety analysis were performed for the center-core rockfill dam(CCRD) The static and pseudo-static FEM analysis using seismic coefficient Method, and dynamic FEM analysis using Hachinohe earthquake wave(0.12g) were used for the seismic safety of CCRD. The results of seismic analysis were that the factor of safety of down slope was 1.5, horizontal displacement is about 14.3cm, and vertical displacement is 3.3cm at dam creast. The model dam did not show any seismic stability problems for 0.12g. And much more research is still necessary in seismic safety of CCRD.

• 한국지진공학회논문집
• /
• 제22권2호
• /
• pp.45-54
• /
• 2018

The seismically isolated nuclear power plants shall be designed for design basis earthquake (DBE) and considered to ensure safety against beyond design basis earthquake (BDBE). In order to limit the excessive displacement of the seismic isolation system of the seismically isolated structure, the moat is installed at a certain distance from the upper mat supporting the superstructure. This certain distance is called clearance to stop (CS) and is calculated from the 90th percentile displacement of seismic isolation system subjected to BDBE. For design purposes, the CS can be obtained simply by multiplying the median displacement of the seismic isolation system against DBE by scale factor with a value of 3. The DBE and BDBE used in this study were generated by using 30 sets of artificial earthquakes corresponding to the nuclear standard design spectrum. In addition, latin hyper cube sampling was applied to generate 30 sets of artificial earthquakes corresponding to maximum - minimum spectra. For the DBE, the median displacement and the 99th percentile displacement of the seismic isolation system were calculated. For the BDBE, the suitability of the scale factor was assessed after calculating the 90th percentile displacement of the seismic isolation system.