• Macromolecular Research
• /
• v.16 no.6
• /
• pp.549-554
• /
• 2008

Proton conducting crosslinked membranes were prepared using polymer blends of polystyrene-b-poly(hydroxyethyl acrylate)-b-poly(styrene sulfonic acid) (PS-b-PHEA-b-PSSA) and poly(vinyl alcohol) (PVA). PS-b-PHEA-b-PSSA triblock copolymer at 28:21:51 wt% was synthesized sequentially using atom transfer radical polymerization (ATRP). FT-IR spectroscopy showed that after thermal ($120^{\circ}C$, 2 h) and chemical (sulfosuccinic acid, SA) treatments of the membranes, the middle PHEA block of the triblock copolymer was crosslinked with PVA through an esterification reaction between the -OH group of the membrane and the -COOH group of SA. The ion exchange capacity (IEC) decreased from 1.56 to 0.61 meq/g with increasing amount of PVA. Therefore, the proton conductivity at room temperature decreased from 0.044 to 0.018 S/cm. However, the introduction of PVA resulted in a decrease in water uptake from 87.0 to 44.3%, providing good mechanical properties applicable to the membrane electrode assembly (MEA) of fuel cells. Transmission electron microscopy (TEM) showed that the membrane was microphase-separated with a nanometer range with good connectivity of the $SO_3H$ ionic aggregates. The power density of a single $H_2/O_2$ fuel cell system using the membrane with 50 wt% PVA was $230\;mW/cm^2$ at $70^{\circ}C$ with a relative humidity of 100%. Thermogravimetric analysis (TGA) also showed a decrease in the thermal stability of the membranes with increasing PVA concentration.

• Journal of the Korea Concrete Institute
• /
• v.29 no.4
• /
• pp.379-387
• /
• 2017

The objective of this study is to develop sustainable PVA fiber-reinforced cementitious composites (FRCCs) that could exhibit comparable strength level to normal PVA FRCCs with no recycled materials. To evaluate mechanical properties of the FRCCs, compressive, flexural and direct tensile tests were conducted. In addition to the test, to calculate amount of carbon dioxide ($CO_2$) emission at the stage of manufacturing the FRCCs, life cycle inventory data base (LCI DB) were referenced from domestic and Japan. From the test results, the mechanical properties such as compressive, flexural and direct tensile strengths were decreased as the replacement ratio of recycled materials increased. And it was determined that the amount of $CO_2$ emission was reduced for the specimens with higher water-binder ratio (W/B) and replacement ratios. It was also found that binder intensity ($B_i$) value was higher as replacement ratio of fly ash (FA) increased. This result means that larger amount of FA is need to deliver one unit of a given performance indicator (1 MPa of strength) of FRCCs compared to that of ordinary portland cement (OPC). As a result, it could be concluded that FRCCs with W/B 45% replaced by FA 25% and recycled sand (RS) 25% is desirable for both target performance and $CO_2$ emission.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.11
• /
• pp.735-742
• /
• 2012

This study tried to find a suitable method for enhancing the foam stability of cationic surfactants that normally generate less foam or no foam. Several trials were made to enhance the foam stability: addition of anionic surfactant, colloids and polymer. Cationic starch (CA-ST) did not form foam at all, while the foam stability of two other cationic surfactant also showed low levels; methyl triethanol ammonium methyl sulfate distearyl ester (CEQ90) for 46 sec. and Cetyl trimethyl ammonium chloride (CM29) for 31 seconds. Foam stability of cationic surfactants were significantly affected by addition of anionic surfactant, sodium dodecyl sulfate (SDS). Foam stability of CA-ST was significantly enhanced by addition of SDS, while those of CEQ90 and CM29 were decreased. Addition of colloids ($SiO_2$, kaolin) and polyvinyl alcohol (PVA) enhanced foam stabilities of CEQ90 and CM29. However, CA-ST did not form foam even in the presence of colloids or PVA. Effect of simultaneous addition of colloids and anionic surfactant on foam stability of cationic surfactant showed that foam stability of cationic surfactant was more influenced by addition of anionic surfactant than colloids. Effect of simultaneous addition of PVA and anionic surfactant on the foam stability of cationic surfactant also showed that presence of anionic surfactant significantly affect the foam stability of cationic surfactant. Foam stability of CA-ST was greatly increased to 8,780 seconds by addition of SDS 0.14% and PVA 2.5%. The foam stability of CA-ST was 8 times higher than CEQ 90. This study suggested that cationic surfactants not forming foam can generate foam by addition of anionic surfactant and its stability can be additionally increased by addition of colloids and PVA. The study results showed that enhancement in foam stability of cationic surfactant was prominently affected by the concentration of anionic surfactant added.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.137-140
• /
• 2009

Nowadays, the high performance composite materials are famous for the new construction materials as the construction buildings are bigger and higher. Out of them of all, the fiber reinforced concrete and mortar have been studied to develop and strengthen the performances of concrete, such as tensile strength, durability and the resistibility of crack. Also, it is considered that precast concrete is important alternatives of dry process for saving time, upgrading the material's quality and the productivity. Thus, PC panel is being produced for the use of dry wall as well as exterior finishing materials and it requires lots of tests and studies to be conducted to meet the various functional conditions. According to this study, it is considered that PVA fiber might be more effective than nylon fiber for developing the exterior PC panels.

• Proceedings of the Korean Fiber Society Conference
• /
• 1991.06b
• /
• pp.94-95
• /
• 1991

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.149-157
• /
• 2017

As the amount of construction wastes increase, reuse of recycled materials is being considered in research areas. While there are many experimental investigations focusing on development of mortar and concrete using the recycled materials, the studies regarding the fiber-reinforced cement composites (FRCCs) using recycled materials are still limited. In this paper, an experimental attempt has been made to investigate the effect of recycled fine aggregates and fly ash on the mechanical properties of PVA FRCCs. The cement and natural sand were respectively replaced by fly ash and recycled fine aggregates at two content levels, 25% and 50%. Ten types of PVA FRCCs mixes were fabricated and tested to investigate the flexural, compressive and direct tensile behaviors. The test results show that flexural, compressive and direct tensile strength were decreased with increase in fly ash content at all ages. In particular, flexural, compressive and direct tensile strengths of specimens, containing 50% recycled fine aggregates and 50% fly ash, showed the lowest values. The modulus of elasticity of specimens showed similar trend to the 28-day compressive strength. Poisson's ratio was increased with increase in fly ash and recycled fine aggregates content.

• Korean Journal of Animal Reproduction
• /
• v.27 no.4
• /
• pp.339-347
• /
• 2003

The purpose of this study was to investigate the development of bovine nuclear transfer (NT) embryos cultured in serum-free conditions. Bovine NT embryos cultured in various culture conditions were compared blastocyst development, total cell number and apoptosis using TUNEL assay. In experiment 1, blastocyst rates of NT embryos were significantly higher (P<0.01) in FBS (22.0％) and BSA (26.6％) groups than in PVA (6.3％) group. Total cell number was significantly higher in FBS (78.4$\pm$19.4) and BSA (90.9$\pm$29.1) groups than in PVA group (46.0$\pm$0.0). Apoptotic cell number was significantly fewer in FBS (3.1$\pm$1.4) and BSA (1.7$\pm$1.4) groups than in PVA group (7.0$\pm$20.0) However, all of results were not different between the FBS and BSA group. In experiment 2, blastocyst rates of NT embryos were significantly higher (P<0.05) in fatty acid free-BSA (FAF-BSA) group (26.8％) than in fraction V-BSA group (11.2％). Total cell number were somewhat higher in FAF-BSA group (89.8$\pm$30.7) than in fraction V-BSA group (88.1$\pm$19.3). Apoptotic cell number were somewhat fewer in FAF-BSA (1.7$\pm$1.5) group than in fraction V-BSA group (4.2$\pm$2.9). These findings suggest that serum free condition were effective for the in vitro development of bovine NT embryos. Therefore, we concluded that fatty acid free-BSA has beneficial effect in development bovine NT embryos and can be use as a serum substitute.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1313-1314
• /
• 2007

This paper presents organic thin-film transistors (OTFTs) with poly(3-hexylthiophene)(P3HT) semiconductor and several polymeric dielectric materials of poly(vinyl phenol)(PVP), poly(vinyl alcohol)(PVA), and polyimide(PI) by using soluble process. The fabricated OTFT's have inverted staggered structure using transmission line method(TLM) pattern. In order to evaluate the electrical characteristics of the OTFT, capacitance-voltage(C-V) and current-voltage(I-V) were measured. C-V graphs were measured at several frequencies of 100 Hz, 1 kHz, and 1 MHz and ID-VDS graphs according to $V_{GS}$. The current on/off ratio and threshold voltage with each of PVP, PVA, and PI based OTFTs were measured to $10^3$, and -0.36, -0.41, and -0.62 V. Also, the calculated mobility with each of PVP, PVA, and PI was 0.097, 0.095, and 0.028 $cm^{2}V^{-1}s^{-1}$, respectively. In the cases of PVP and PVA, the hole mobility of P3HT was in excellent agreement with the published value of 0.1 $cm^{2}V^{-1}s^{-1}$.

• Journal of Embryo Transfer
• /
• v.20 no.3
• /
• pp.303-309
• /
• 2005

This study was conducted to examine the effects of OA on metaphase of meiosis II and the mitochondrial activity of cytoplasm in bovine cumulus oocytes complexes(COCs) during in vitro maturation. Hanwoo COCs were collected from the slaughterhouse cow ovaries and matured in TCM199 supplemented with $0.1\%$ PVA, 0.2 uM, 2 uM, 20 uM OA for the maturation rate of OA concentration. For the maturation effects between OA and cycloheximide(CX), COCs were matured in TCM199 with 25 ug/mL CX, 25 ug/mL CX (6 hrs culture) plus 2 uM OA or 2 uM OA only at a atmosphere $5\%\;CO_2,\;95\%$ air $39^{\circ}C$ for 6, 12, 24 hrs. To evaluate the nuclear types of matured COCs, cumulus cells were removedby $0.5\%$ hyaluronidase sol. and oocytes were fixed in 1:3 acetic acid ethyl alcohol for 30 sec. and then stained with $0.1\%$ basic Fuchsin sol. For the detection of fluoriscent intensity (FI) of matures oocytes, cumulus cells were removed same as performed above and were stained with 20 nM mite tracker for 20 min. at $39^{\circ}C$. Mitochondrial activity of FI in matured oocytes was imaged by laser conforcal microscopy (Fluoview, Olympus, Japan) and were measured scanned face on 5 um from median to endpoint of oocytes. Statical analysis of nuclear types observed the three replicates was carried out with ANOVA and Fisher's protected least significant difference test using the STATVIEW program. FI of matures oocytes was compared the multiples of the least intensity among the measured oocytes. Maturing in TCM199 supplemented with $0.1\%$ PVA, 0.2 uM, 2 uM, 20 uM OA, metaphase B were showed 72.0, 50.0, 70.0, $68.8\%$, respectively and there were different significant(p<0.05). In the case of treatment with OA and CX, metaphase were $73.8\%,\;8.2\%,\;45.5\%,\;73.7\%$ in $0.1\%$ PVA-TCM199, 25 ug/mL CX, 25 ug/mL CX plus OA or 2uM OA only, respeclively. FI was revealed the increasing tendency during the process of maturation. Whereas FI in CX was decreased about 3 times compared to the other treatments of 6 hrs maturation. We conclude that OA regulates bovine COCs maturation and induces the mitochondrial activity during the process of maturation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.927-931
• /
• 2004

본 논문에서는 혈당측정기 제작에 있어 PDMS(Su-8)를 이용하였다. 이는 일종의 고분자로서 기계적 특성이 우수하고 제작이 간단하며, 가격이 저렴하고 다른 물질과의 접합이 용이하다. 혈액의 펌핑과 믹싱을 할 수 있도록 새로운 구조체를 설계하였으며 제안된 모델의 핵심 부분인 측정전극의 제작에 필요한 기초적인 실험을 수행하였다. 측정전극의 성능향상과 제작편의성, 저가격화를 위해 효소고정화방법으로 Electrospinning (전기방사)으로 제조된 PVA nanofiber web을 이용하였으며, 이는 중합도 Pn=1700, 비누화도 98%인 공업용으로 상용화된 값싼 제품이다. 따라서 이를 이용하면 측정용 전극의 효소고정화에 있어 저가격화를 이룰 수 있을 것으로 기대된다 고정화된 전극분석을 위해 SEM(주사전자현미경)과 NMR(핵자기공명분광계), FT-IR(적외선분광분석)장비를 사용하였다. 그리고 기존의 효소고정화법(전기중합법)과의 응답특성을 비교분석하였다.