• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1320-1326
• /
• 2011

The maximum speed of high-speed rail is restricted to various factors such as track condition including slope and radius, tunnel and dynamic stability of vehicle. Among the various factors, traction effort and resistance to motion is principal and basic factor. In addition, at high speed over 300km/h, aerodynamic drag amounts up to 80% of resistance to motion, that it can be said that aerodynamic drag is the most important factor to decide the maximum speed of high-speed rail system. This paper deals with a measure to increase the maximum speed of high-speed train by reducing aerodynamic drag. The traction effort curve and resistance to motion curve of existing high-speed train under development has been employed to set up the target of aerodynamic drag reduction to reach up to 500km/h without modification traction system. In addition, the contribution of various sources of aerodynamic drag to total value has been analyzed and the strategy for implementation of aerodynamic drag reduction has been discussed based on the aerodynamic simulation results around the train using computational fluid dynamics.

• 오토저널
• /
• 제11권1호
• /
• pp.57-67
• /
• 1989

본 연구에서는 음향 인텐시티법을 가솔린 엔진에 직접 적용하여, 각각의 중심주파수별 음향인텐시티 응답특성을 1/3옥타브 밴드로 구하였고, 오버올 레벨 및 최대 인텐시티레벨을 갖는 중심주파수에서의 음향 인텐시티 방사특성을 등고선 및 3차원 표시로 나타내었다. 또한 그 결 과를 분석 및 고찰하여 엔진의 중요 소음원을 검출하므로써 이 수법이 소음대책에 유효하다는 것을 검증하였다. 연구 결과, 오버올 레벨에서는 아이들링 상태의 경우 엔진 전면부에서, 2,000 rpm 상태의 경우 엔진 우측부에서 가장 높은 음향 인텐시티가 방사되었으며, 최대 인텐시티레 벨을 갖는 중심주파수에서는 오일팬과 흡, 배기매니홀드가 100Hz에서 가장 높은 음향 인텐시티를 나타내었다.

• Journal of Radiation Protection and Research
• /
• 제32권1호
• /
• pp.15-20
• /
• 2007

An empirical formula fur the neutron dose equivalent at the maze entrance of medical accelerator treatment rooms was derived on the basis of a Monte Carlo simulation. The simulated neutron dose equivalents around the Varian medical accelerator by the MCNPX code were employed. Two cases of target rotational planes were considered: parallel and perpendicular to maze walls. Most of the maximum neutron dose equivalents at the doorway were found when the target rotational planes were parallel to maze walls and the beams were directed to the inner maze entrances. The neutron dose equivalents at the outer maze entrances were calculated for about 698 medical accelerator facilities which were generated from the geometry configurations of running treatment rooms, based on such gantry rotation that produces the maximum neutron dose at the doorway. The results calculated with the empirical formula in this study were compared with those calculated by the Kersey method for 7 operating facilities. It was found that the maximum disagreement between the calculation of this study and that of the Kersey method was a factor of 8.54 with the value calculated by the Kersey method exceeding that of this study. It was concluded that the kersey method estimated the neutron dose equivalent at the doorway computed by MCNPX more conservatively than this study technique.

• 동력기계공학회지
• /
• 제14권3호
• /
• pp.13-18
• /
• 2010

HCCI engines fueled DME and natural gas have been studied on single-cylinder engine due to availability of reducing on $NO_X$ and PM simultaneously without deteriorating into high thermal efficiency, and thus it is clarified that higher maximum engine load is achieved as DME equivalence is smaller. In this study, combustion tests were accomplished on multi-cylinder engine for practical use of it. When minimum DME equivalence achieved maximum engine load on single-cylinder engine was applied to 4-cylinders engine, there was in unstable running condition that engine revolution fluctuated greatly and cyclically. It is the reason what misfire occurred intermittently with one the same as minimum DME equivalence on single-cylinder due to increase in energy for ignition at No. 1 cylinder with lower cylinder liner temperature. Maximum engine load was achieved by adopting EGR, though it decreased because of knocking at smaller engine load than single-cylinder due to increase in minimum DME equivalence.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.437-444
• /
• 2007

This paper experimentally investigates the effects of oxygen-enriched air (OEA) on the running behaviors of an LPG SI engine during both start/warm-up (SW) and hot idling (HI) stages. The experiments were performed on an air-cooled, single-cylinder, 4-stroke, LPG SI engine with an electronic fuel injection system and an electrically-heated oxygen sensor. OEA containing 23% and 25% oxygen (by volume) was supplied for the experiments. The throttle position was fixed at that of idle condition. A fueling strategy was used as following: the fuel injection pulse width (FIPW) in the first cycle of injection was set 5.05 ms, and 2.6 ms in the subsequent cycles till the achieving of closed-loop control. In closed-loop mode, the FIPW was adjusted by the ECU in terms of the oxygen sensor feedback. Instantaneous engine speed, cylinder pressure, engine-out time-resolved HC, CO and NOx emissions and excess air coefficient (EAC) were measured and compared to the intake air baseline (ambient air, 21% oxygen). The results show that during SW stage, with the increase in the oxygen concentration in the intake air, the EAC of the mixture is much closer to the stoichiometric one and more oxygen is made available for oxidation, which results in evidently-improved combustion. The ignition in the first firing cycle starts earlier and peak pressure and maximum heat release rate both notably increase. The maximum engine speed is elevated and HC and CO emissions are reduced considerably. The percent reductions in HC emissions are about 48% and 68% in CO emissions about 52% and 78%; with 23% and 25% OEA, respectively, compared to ambient air. During HI stage, with OEA, the fuel amount per cycle increases due to closed-loop control, the engine speed rises, and speed stability is improved. The HC emissions notably decrease: about 60% and 80% with 23% and 25% OEA, respectively, compared to ambient air. The CO emissions remain at the same low level as with ambient air. During both SW and HI stages, intake air oxygen enrichment causes the delay of spark timing and the increased NOx emissions.

• 대한교통학회지
• /
• 제22권5호
• /
• pp.75-87
• /
• 2004

우리나라 해안지역은 강풍의 빈도가 높고 세기도 크지만 아직까지 바람을 고려한 적정속도를 안내하는 시스템은 전무한 상태이다. 강풍이 부는 곳에서의 무리한 주행은 핸들 조작의 어려움으로 인한 사고 위험과 풍속을 고려하지 않은 과속으로 인한 전복사고 등의 위험이 크다. 이러한 측면에서 바람 잦은 곳 중 주요지점에 기상정보센서(WIS:Weather Information Sensor)를 설치하고 이로부터 실시간으로 측정된 기상정보를 바탕으로 차량의 구동력과 주행저항의 크기를 극대화하는 적정속도를 VMS를 통하여 제공하는 방안이 필요하다. 목포시에 건설예정인 목포대교를 대상으로 풍속별 적정 속도를 산출한 결과, 연중 평균 풍향인 남풍일 경우 교량의 입지(정남-북)에 따라 남측으로 주행하는 차량에 대하여 풍속이 8m/h이상일 경우에는 평상시와 달리 돌풍을 대비한 여유구동력이 큰 60km/h의 속도를 안내해 주는 것이 바람직 한 것으로 나타났다. 또한 2003년도에 발생한 태풍 매미 시 목포시의 풍속인 18m/s 일 경우 시속 40km/s에서의 주행저항은 1131N으로써, 이미 변속 4단에서의 구동력(약 1054N)으로는 극복할 수 없으므로 3단 이하에서 변속을 하여야 하며, 이때의 적정속도는 주행저항과 구동력간의 차이가 가장 크게 발생하는 40km/h인 것으로 분석되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권2호
• /
• pp.9-17
• /
• 2022

차세대 고속철은 주행 속도가 점점 증가하므로 이를 반영한 고속철 차량 통과교량에 대한 새로운 주행 안정성의 평가가 요구된다. 이를 위하여 현재 공용 중인 경부 고속철 구간의 대표 교량형식인 PSC (Pre-stressed Concrete) 박스거더 교량을 대상으로 관성질량을 고려한 38-자유도 차량과 궤도 불규칙성과 상호 작용력을 반영하여 모형화하였으며, 고속철 차량 주행속도 별로 동적 수치해석을 수행하여 주행 안정성을 평가하였다. 수치해석을 통해 단순교와 2 경간 연속교의 최대 수직 변위와 DAF (Dynamic Amplification Factor; 동적확대계수)를 산출하여 동적 안정성 여부를 판단하였으며, 또한 주행 속도 별 최대 수직 변위를 추정하기 위한 3차 다항 회귀 분석식을 제안하였다. 대표적인 주행 속도와 횡 단면 위치 별 수직 변위 차이를 비교하고, 종 방향 최대 면틀림을 분석하였다. 또한, 고속철 차량의 교량통과 중 교량의 수직변위에 대한 가속도 영향선과 각 항목 간의 연관성을 분석하여 주행 안정성을 평가하였다.

• 한국운동역학회지
• /
• 제15권2호
• /
• pp.93-102
• /
• 2005

The purpose of this study was to examine the effect of step length on the joint moment. The subjects were 4 undergraduate and graduate students in their 20s with normal legs. The subjects were individually tested by the running timer at the walking speed of 0.67m/s, 134m/s, and 2.46m/s. The step length was regulated to -10% of normal, normal and +10% of normal step length using foot print. The walking performances of each subjects were filmed using a high speed video camera. The raw data were analyzed by LabVIEW Graphical Program and these data were analyzed by ANOVAs and Scheffe. The results of this study were as follows: The maximum dorsiflexion moment of the ankle joint increased as the step length increased only at the fast walking speed. Although there wasn't significant difference shown in the plantar flexion moment, regular pattern in the plantar flexion moment which increased as the step length increased was found. The first maximum extension moment of the knee joint increased only at the normal walking speed, but there appeared no significant difference in the maximum flexion and second extension moment. The maximum extension moment of the hip joint increased at the normal and fast walking speed. Although there wasn't significant difference, regular pattern in flexion moment which increased as the step length increased was found.

• 농업과학연구
• /
• 제46권3호
• /
• pp.613-627
• /
• 2019

The purpose of this study was to design a powertrain for a 78 kW AWD (all wheel drive) electric tractor by analyzing the combination of various reduction gear ratios on a commercial motor using data from actual agricultural work and driving conditions. A load measurement system was constructed to collect data using wheel torque meters, proximity sensors, and a data acquisition system. Field experiments for measuring load data were performed for two environmental driving conditions (on asphalt and soil) and four agricultural operations (plow tillage, rotary tillage, loader operation, and baler operation). The attached implements and gear stages were selected through farmer surveys. The range of the reduction ratio was determined by selecting the minimum reduction ratio needed to satisfy the torque condition required for agricultural operations and the maximum reduction gear ratio to satisfy the maximum travel speed. The minimum reduction gear ratio selected was 57 in consideration of the working load condition and the maximum reduction gear ratio selected was 62 considering the maximum running speed. In the range of the reduction gear ratio 57 - 62, the selected motor satisfied all working torque conditions. As a result, the combination of the selected motor and reduction gear ratio was applicable for satisfying the loads required during agricultural operation and driving operation.

• 농업과학연구
• /
• 제37권1호
• /
• pp.37-43
• /
• 2010

This study carried out to develop barrier-free certification program in forest trail. It is done to provide the certification system presented about certification organized, certification standard and indexes, evaluation method and operation plan. In order to develop certification program in forest trail, detailed measurement index must be developed earlier based on an accessbility, a stability, a preservation and a walking continuity. The suitable forest trail for weak pedestrian was investigated that running slope should be 1/20(5%) maximum, cross slope cannot exceed 1/50(2%) maximum and clear tread width should be above of minimum 90cm. In addition, the trail type is designed as a mixed trail system which is a combination of the loop and the line form and its distance should be 225~675m. Finally, forest trail should be manage sustainably by having regular monitoring and evaluation.