• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.38-44
• /
• 2010

75톤급 개방형 액체로켓용 터보펌프 터빈의 성능시험을 수행하였다. 넓은 압력비와 회전수 영역에서 터빈의 출력을 측정하였으며 이를 통해 터빈로터 전후의 유동특성을 파악하였다. 이와 함께 터빈의 효율 변화 및 측정된 로터입구의 압력을 기 개발된 30톤급 터빈과 비교하여 설계 의도에 부합되는 향상된 성능의 동익을 재설계하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1047-1048
• /
• 2007

In this paper, the harmonic loss of the inverter driven induction motor was analyzed. It was analyzed through the theoretical consideration on the variations of equivalent circuit constants, and harmonic losses, including the effects of resistance increase and inductance decrease of stator, not through the general method that considering just the effects of the harmonic losses of only the rotor. It was verified by comparing the harmonic analysis results with the test results for HHI's inverter driven motor.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.219-226
• /
• 2002

This paper is concerned with the effects of periodically approaching upstream wakes on cascade-flow and loss. The reduced frequency of the periodic wakes was varied in the narrow range from 0.5 to 0.7 Corresponding to a wake-passing through the cascade, two velocity deficits appeared near the boundary layer contour in the downstream from about 60% chord-length. The first velocity deficit was caused by a periodic wake and the second one appeared after some delayed time. The second velocity deficit was interpreted as the results of reattachment of flow-separation. The higher reduced frequency decreased the duration time of separation appearance and the lesser losses of blade were resulted.

• 한국태양에너지학회 논문집
• /
• 제34권2호
• /
• pp.8-15
• /
• 2014

The objective of this paper is to suggest a design topology of permanent magnet synchronous generator with 2,000kW capacities for wind turbine. The suggested topology is to provide 3 split magnet PMSG instead of single magnet, and performed an analysis of eddy current loss and iron loss for suggested type using ansoft maxwell commercial program. The simulation results of suggested magnet type show there duction of eddy current loss as 13.87kW with loadless conditions and23.48kW with rated conditions, but iron loss for rotor yoke show the in creasing trend as2.2kW with loadless conditions and 0.2kW with rated conditions. The suggested 3 split maget type is to identified as more useful for 2,000kW PMSG.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.34-39
• /
• 2005

본 논문에서는 3차원 초음속 노즐 형상 변수에 따른 부분입사형 터빈의 유동 및 성능 특성을 알아보기 위하여 3차원 노즐 형상 변수를 노즐 모양 및 노즐 출구 단면 형상으로 설정하여 전산해석을 실시하였다. 먼저 노즐 모양에 따른 유동 및 성능 특성을 비교해 본 결과, 사각형 노즐이 원형 노즐보다 축방향 간극내에서 발생하는 전압력 손실이 적었으며, 이로 인하여 파워가 약 1.5% 증가하였다. 다음으로 사각형 노즐출구단면의 면적에 따른 유동 및 성능 특성을 비교해 본 결과, 노즐 출구 단면과 로터의 hub/tip 사이의 간극과 노즐간의 간격이 터빈 성능에 크게 영향을 줌을 확인할 수 있었다.

• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.24-30
• /
• 2011

500W class MTG(Micro turbine generator) operating at 400,000 rpm is under development. From the cycle analysis, it is decided that the self-sustaining speed of MTG is 200,000rpm and the generating speed is 400,000 rpm. Therefore, motor should be designed so that it is able to rotate the rotor up to 200,000rpm and generator should designed so that it is able to generate 500W output at 400,000rpm. First step to design motor/generator is to determine the power and efficiency requirement. Not only the power into the compressor and from the turbine at the operating speed but also the mechanical and electrical losses should be considered in determining the power and efficiency requirement. This study presents the procedure and the results of determining the power and efficiency requirement considering the mechanical and electrical losses depending on the rotating speed which is measured from the experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권6호
• /
• pp.669-676
• /
• 2006

The optimum design and the performance analysis software called POSEIDON for the HAWT (Horizontal Axis Wind Turbine) is developed by use of BEMT, which is the standard computational technique for prediction of power curves of wind turbines. The Prandtl's tip loss theory is adopted to consider the blade tip loss. The lift and the drag coefficient of S-809 airfoil are predicted via X-FOIL and the post stall characteristics of S-809 also are estimated by the Viterna's equations.$^{[13]}$ All the predicted aerodynamic characteristics are fairly well agreed with the wind tunnel test results. performed by Sommers in Delft university of technology. The rated power of the testing rotor is 20kW(FIL-20) at design conditions. The experimental aerodynamic parameters and the X-FOIL data are used for the power Prediction of the FIL-20 respectively The comparison results shows good agreement in power prediction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.705-706
• /
• 2008

There has been, in recent years, effort to make cast copper rotors for industrial use of induction motors. Because the incorporation of copper for the conductor bars and end rings of the induction motor in place of aluminum would result in attractive improvements in motor energy efficiency. The purpose of this method is a reducing the copper loss as using higher conductivity of copper. In this paper as the single phase induction motor is studied, the stator slots and coil turn number is designed for adjusting the slot fill factor and improving its efficiency. At this time design is basis on calculation of reducing loss. And finally this paper shows that the before and after result is compared and analyzed.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권10호
• /
• pp.483-493
• /
• 2001

The 3-phase induction is used for the MCP(main coolant pump) and the pure water is used for lubrication of bearing because of the difficulty of repair. Therefore the type of motor is the canned-motor that is welded by sealed can to prevent the stator and rotor from the lubricating water. A lot of Eddy currents are produced in the can because of the conductivity of material. And these eddy currents in the can are the most important cause that decrease the efficiency of induction motor. Therefore we have to find the method to decrease these eddy currents in the can for the improvement of efficiency of motor. In this paper, we proposed the method of design and analysis of canned-motor using equivalent circuit with consideration of can loss for the improvement of efficiency of motor.

• 한국소음진동공학회논문집
• /
• 제16권11호
• /
• pp.1172-1178
• /
• 2006

Measurement of blade strain with sensors directly installed on the blade has one critical issue, how to send the sensor signal to the ground. Strain-gauges have been dominantly used to directly measure stress of a blade and either a slip ring or a telemetry system has to be used to send measured signal to the ground. However, both systems have many inherent problems and sometimes very severe limitations to be practically used. In this paper, new on-line strain monitoring method using. FBG(Fiber Bragg Grating) sensors and a beam coupler is introduced. Measurement of rotor stress using FBG sensors is nothing new, but unlike other system which installs all necessary instruments on the rotor and use telemetry system to send data to the ground, this system makes use of light's unique characteristic - light travels through space. In this new approach, single optical fiber with many FBG sensors is installed on the blade and all other necessary instruments can be installed at ground thereby giving tremendous advantages over slip ring or telemetry system. A reference sensor is also introduced to compensate the beam coupler's transmission loss change due to rotation. The suggested system's good performance is demonstrated with experiments.