• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.512-517
• /
• 1993

The cold rolled strip meets continuously rising demands on the less deviation of thickness at the width direction of their rolled products. Especially, the special interest has been to find the methods to reduce the edge drop which influences seriously on the yield losses and the quality of the rolled products. In this study, the influence of hot coils on the thickness profile of cold rolled strip was analyzed. For obtainint the tapered work roll shig\ft conditions, the thermal crown and the flattening between the work roll and the strip were calculated, and the main parameters which have mostly effects on the edge drop were simulated. Also the obtained conditions from the simulation were applied to Tandem Cold Rolling Mill to investigate the change of the edge drop and the crown ratio depending on the amount of work roll taper and the length of contact of taper. The results of the application led to better thickness profile than conventional one.

• 자원리싸이클링
• /
• 제11권5호
• /
• pp.24-29
• /
• 2002

철강압연공장에서 산세공정중 발생하는 산화철의 색상을 개선하기 위하여 배소로 조업과 색상혼합공정을 연구하였다. 배소로 조업에서는 조업온도, 폐산장입량, 폐산분사 노즐수에 대하여 검토하였으며, 색상혼합공정에서는 산화티탄, 실리카, 괴타이트를 색상혼합재로 검토하였다. 배소로 조업에서는 조업온도를 낮게 할수록 산화철의 명도가 개선되었으며, 색상혼합공정에서는 괴타이트 첨가 경우에 제일 많이 산화철의 적색 및 명도가 개선되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.350-354
• /
• 1995

The Tension Leveller of Cold Rolling Mill In POSCO performs levelling the strip in high speed line. But minor variations in operating condition of driving machines such as motor, gear box, and support bearings, a small gap-variation of supporter and strip slip by poor roll revolutions can cause serious problems in the quality of strip. In this study, firstly, A condition monitoring standard for each sensor is made through with the detail analysis of vibration and strip slip. Secondly, An automatic monitoring and diagnosing system was developed to monitor the condition of Tension Leveller, and diagnose the cause of abnormal condition. Finally, A diagnosing algorithm for abnormal condition and man-machine interface (MMI) for easy operation are developed.

• International Journal of Control, Automation, and Systems
• /
• 제5권1호
• /
• pp.43-50
• /
• 2007

Reheating furnace is an essential facility of a rod mill plant where a billet is heated to the required rolling temperature so that it can be milled to produce wire. Although it is very important to obtain information on billet temperatures, it is not feasible during furnace operation. Consequently, a billet temperature profile should be estimated. Moreover, this estimation should be done within an appropriate time interval for an on-line application. In this paper, a billet heat transfer model based on 2D FEM(Finite Element Method) with spatially distributed emission factors is proposed for an on-line billet temperature estimation and also a measurement is carried out for two extremely different furnace operation patterns. Finally, the difference between the model outputs and the measurements is minimized by using a new optimization algorithm named uDEAS(Univariate Dynamic Encoding Algorithm for Searches) with multi-step tuning strategy. The obtained emission factors are applied to a simulation for the data which are not used in the model tuning for validation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.179.6-179
• /
• 2001

This paper proposes the recognition method of the strip shape using the Least-Square method and the distinction method of the asymmetric shape and the compensation method upon the shape control values for the stainless steel cold rolling mill. This paper proposes the shape recognition method before control and the compensation method to minimize the fluctuation of the shape deviation and to get symmetric shape. This paper shows on line test results to verify the performance of the control method for the process. The experiments have been performed with respect to various material type, thickness, and strip width. The performance of the proposed method is obtained excellent quality and high productivity as results.

• 제어로봇시스템학회논문지
• /
• 제8권5호
• /
• pp.373-384
• /
• 2002

This paper presents a robust PID controller design technique using the concept of model matching method in the frequency domain. To design the robust PID controller satisfying disturbance attenuation and robust tracking property for a reference input, first an H$\infty$ controller satisfying given performance is designed using the H$\infty$ control method. And then, the parameters(proportional, integral, and derivative gains) of the robust PID controller are determined using the model matching at frequency domain. The proposed technique is applied to a position controller design of the web. The simulation results show that the proposed robust PID controller satisfies disturbance attenuation and tracking property.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1412-1416
• /
• 2003

Induction Heaters are commonly used in heating steel strip product, because it can rapidly and efficiently heat steel strip/bar. In this study, a inductive heating model is developed and the predictions are compared with measured temperatures. The temperatures are measured from POSCO thin-slab rolling facility (so called Minimill). Induction heater is installed between reduction unit and holding furnace This induction heater raise the temperature of steel bars from $930^{\circ}C$ to about $1100^{\circ}C$ which gives the required temperature for finishing mill process after holding period at holding furnace. Unlike other simple equation models, this model allows us to predict temperature profiles of sections of steel bars.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.251-256
• /
• 2009

The effect of austempering treatment on mechanical properties of nodular indefinite chilled iron(NICI) and ductile cast iron(DCI) was investigated. In microstructural observation, matrix phase(pearlite and ferrite) was changed to ausferrite after austempering treatment both DCI and NICI. In case of NICI, decomposition of cementite($Fe_3C$) during austempering treatment was induced. After austempering treatment, mechanical properties such as hardness, tensile strength and impact toughness was improved in NICI and DCI. The wear resistance is slightly decreased because of decomposition of cementite during austempering treatment in NICI but impact toughness and strength is dramatically increased.

• Advances in Computational Design
• /
• 제5권3호
• /
• pp.261-276
• /
• 2020

The reasonable layout of vacuum cleaner can effectively improve the collection efficiency of iron filings generated in the process of steel production. Therefore, in this study, the CFD-DEM coupling model and two-fluid model are used to calculate the iron filings collection efficiency of vacuum cleaner with different inclination/cross-sectional area, pressure drop and inlet angle. The results are as follows: The CFD-DEM coupling method can truly reflect the motion mode of iron filings in pneumatic conveying. Considering the instability and the decline of the growth rate of iron filings collection efficiency caused by high pressure drop, the layout of 75° inclination is suggested, and the optimal pressure drop is 100Pa. The optimal simulation results based on two-fluid model show that when the inlet angle and pressure drop are in the range of 45°~65° and 70Pa~100Pa, larger mass flow rate of iron filings can be obtained. It is hoped that the simulation results can offer some suggestion to the layout of vacuum cleaner in the rolling mill.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.144-148
• /
• 2001

In this study, to improve the color of iron oxide from waste pickling acid at the cold rolling mill, quality control technologies to improve color were investigated. During operation of the spray roaster, the charge amount of waste acid per hour, temperature, and numbers of spray nozzles were investigated. At the admixing process, titanium oxide, silica, and goethite were tested. The color character of iron oxide can be improved by process control of the spray roaster and the admixing process at a pigment factory. Iron oxide from this study is appropriate for use as a colorant of a concrete product.