• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.327-333
• /
• 2003

Most of shape defects in steel strip are originated from the structure of rolling mill itself. For instance, strip crown occurs when the work roll is deformed by the bending moment induced on roll chocks. To get rids of the shape defects, it is necessary to increase the stiffness of rolling mill. The structure change of back-up roll is one of alternative ways to increase the mill stiffness without facility revamping from 4 high mill to 6 high mill. In this research work, the new back-up roll was developed and can be used in any type of 4 high mill to reduce the strip shape defects. The developed back-up roll consists of sleeve, arbor and phase angle adjusting system for arbor. The circumference of arbor is specially machined to adapt the strip width change during rolling. The experimental cold rolling test was done to prove the effectiveness of newly developed back-up roll. The experimental rolling results show that the new back-up roll has more powerful performance in reducing the shape defects than conventional back-up roll. It was also found that the new back-up roll has higher stability for shape control. In addition to, the only sleeve surface needs to be reground and changed in most cases, so that the maintenance cost can be greatly reduced.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.252-255
• /
• 2009

The roll gap set-up in the finishing mill is one of the most important technologies in the hot plate rolling process. As the target thickness can be obtained by the correct set-up of the roll gap, improving the roll gap set-up technology is very critical for plate thickness accuracy. The main cause of thickness variation in hot plate mills is the non-uniform temperature distribution along the length of the slab. The objective of this study is to adjust the roll gap set-up for the thickness accuracy of plate in hot rolling process considering top-end temperature drop. Therefore this study has concentrated on determining the correct amounts of roll gap to compensate thickness variation due to top-end temperature drop. The off-line simulation of compensated roil gap significantly decreases top-end thickness variation.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.290-295
• /
• 2009

The roll gap set-up in the finishing mill is one of the most important technologies in the hot plate rolling process. As the target thickness can be obtained by the correct set-up of the roll gap, improving the roll gap set-up technology is very critical for plate thickness accuracy. The main cause of thickness variation in hot plate mills is the non-uniform temperature distribution along the length of the slab. The objective of this study is to adjust the roll gap set-up for the thickness accuracy of plate in hot rolling process considering top-end temperature drop. Therefore this study has concentrated on determining the correct amounts of thickness variation according to top-end temperature drop and roll gap to compensate thickness variation. The control method of roll gap set-up which can improve the thickness accuracy was proposed. The off-line simulation of compensated roll gap significantly decreases top-end thickness variation.

• Transactions of Materials Processing
• /
• v.24 no.3
• /
• pp.212-217
• /
• 2015

SmartCrown is a system to control the plate crown by shifting the sine-shaped work rolls in the axial direction. The control range of the plate crown depends on a depth of sine-shaped roll profile because the roll radius varies continuously along the axial direction. When the roll profile is changed to improve the control range, the contact stress between the work roll and the back-up roll also changes. In the current study, the contact stress for various profiles and rolling conditions were analyzed using the finite element method and compared with results from Hertzian contact theory. A submodel method is used to increase the accuracy of the finite element analysis. The analysis results showed that the maximum increase in the contact stress was only 53MPa, so it is anticipated that no back-up roll spalling will occur.

• Journal of Bio-Environment Control
• /
• v.4 no.2
• /
• pp.232-239
• /
• 1995

This study was carried out to get required torque data needed to design and develop a roll-up ventilation system in a pipe-constructed plastic film green-house. The results obtained from this study are as follows : 1. The required torques of a roll-up ventilation system in greenhouse are the functions of its length. The torques should multiplied by the conversion coefficients (2.0 in ceiling vent, 1.8 in side vent) in case of application. 2. In constructing pipe-constructed plastic film greenhouse, a shaft pipe is the largest essential element in roll - up shaft weight constitution which have an effect on the required torques. Therefore, the pipe should be light using nonferrous materials like aluminum alloy. 3. A planetary reduction ventilator of differential ring gear type is suitable for a roll-up ventilation system, because it can make high efficient reduction just using the first step shift.

• Transactions of Materials Processing
• /
• v.5 no.3
• /
• pp.232-238
• /
• 1996

A dynamic mill set-up technique was developed to achieva a more precise roll gap set-up of the finishing mill stands for steel strip rolling. In the conventional mill set-up model the set-up values such as roll gap and roll speed are determined before the sheet bar reached the entry side of the finishing mill train and maintained constant until the strip top end passes through the last stand. In the way however a dynamic set-up logic that gives a way to adjust the roll gap value of the final mill stand for the strip ingoing from the ahead of the front stand was developed and attached to the existing set-up model. The roll gap modification is based on the analysis of the observation in the third stand of the finishing mill train. The dynamic set-up model was proved very effective for the more precise mill set-up and for operational stability in the hot strip finishing mill train.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.88-97
• /
• 1999

In this study, a systematic approach for roll pass design in bar rolling was studied. To minimize the trial and errors in the process design, a roll CAD system and a FE analysis system were combined. Based on the system, a methodology for roll pass design by FEM was studied. At first, designed process was compared with the FE analysis results and process redesign based on the FEM results was performed to obtain the specified final geometry. Then, empirical formula for roll speed set-up was compared with the FE analysis results. Further study on various simulations for bar rolling will help in making up for the inaccuracy in the currently used empirical roll speed rules. In addition, verification of the accuracy of the FE analysis system must be performed using experimental data in the industry.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.62-64
• /
• 2009

Control of back-up roll deformation and wear profile in plate rolling is important not only for enhancement of the structural precision of mill, but also for improving the yield and rolling operation. in the heavy plate mill, there have been strong demands for upgrading back up roll operation technology. In order to satisfy these demands, it is essential to develop the backup roll deformation analysis models and wear profile prediction models. This paper gives a general description of the backup roll deformation and wear model, simulation result for deformation analysis and wear profile.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.144-147
• /
• 1998

VCR is a back-up roll with a special contour which leads to the length of the contact line between back-up roll and work becones self adjustable in accordance with the width of the strip. The simulation of a finite element model and the on-line test at production mill demonstrate that the VCR roll may keep the crown of the roll gap relatively stable, and at same time, permit the rolling pressure to be adjusted over a wider range, and increase the effect of work roll bending on the roll gap. The VCR rolls have been successfully used at the first stands of two largest cold rolling mills in China, and on-line test has been done at a wide hot strip finishing train. The use of VCR roll has created favorable conditions for subsequent rolling passes and the achievement of better flatness quality.

• 한국기계연구소 소보
• /
• s.16
• /
• pp.3-16
• /
• 1986

The first specimens were sampled across the depth of roll products processed by rapid heating and cooling of the roll, namely, differential heat treatment. The second samples were taken from the non-heat treated roll at different depths. The samples were heat treated following the same temperature history as that at each corresponding location in the roll where the samples were taken. Consequently, both specimens showed the similar microstructure and mechanical properties (tensile, impact and fatigue strength etc.)