• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1563-1568
• /
• 2012

Printed electronics is a technology used for forming electronic circuits or devices, and it is used in the manufacture of many products such as RFID tags, solar cells, and flexible display panels with a much lower cost than in the case of semiconductor process technology. Web-guide-type printing such as roll-to-roll printing is a method used to produce printed electronic devices in a large volume. To commercialize such products, highly precise alignment between printed layers is required. In this study, a highly precise alignment system is proposed, and some experimental results are compared with those obtained using a laser surface vibrometer to illustrate the reliability of the proposed system. The robustness of the proposed system to web deformation is also considered experimentally.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.33-42
• /
• 2004

Making use of SN steel in the building structure should be a prerequisite to adopt the design strength of said steel. As a preceding study, the material properties of STKN400B/490B tubes and SPAP235/325 and SPAR295 square pipes manufactured using SN400B/490B plates were evaluated. Compared with the yield and ultimate strengths of SN400B/490B plates, those of STKN400B/490B tubes increase. Nonetheless, the yield and ultimate strengths of STKN400B/490B tubes satisfied the design codes of STKN400B/490B tubes even though the tubes were fabricated via roll bending or press forming. On the other hand, the yield and ultimate strengths at the edges of SPAP235/325 square pipes did not satisfy the design codes based on the values at the sides. The maximum tensile and compressive residual stresses at the SN490B tube were equal to and 40% of the yield strength of the SN490B plate, respectively, In the case of the SPAP325 square pipe, both the maximum tensile and compressive residual stresses were 80% of the yield strength of the SN490B plate. The axial compressive loaded column test results snowed that the buckling strengths were not very different regardless of the mode of fabrication of STKN490B tunes. i.e., through roll bending or press forming. On the other hand, the buckling strength of the SPAP325 square pipe was higher than that of the built-up square pipe.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.190-193
• /
• 2008

Thick pipes which have large thickness have been used in fields of ocean and industrial plants, and for oil pipelines, water pipes and pipe arrangement. In manufacture of the pipes, roll bending process has been used mostly. However, studies on the pipe forming processes using brake press have been performed in recent days. Normally, the brake press has high aspect ratio, so analysis of structural integrity should be conducted. In this study, the evaluation of structural integrity of the brake bending press was carried out for thick pipe forming process.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.824-827
• /
• 2011

본 논문에서는 자동차 시트 리클라이너 기어의 파인 블랭킹 성형 실험을 통하여 V-링 설치 위치에 따른 기어의 다이 롤 높이 변화를 검토하였다. 3 종류의 다이 편과 가이드 플레이트 편을 설계하여 파인 블랭킹 금형을 제작하였으며 650 ton 파인블랭킹 프레스에서 성형 실험을 수행하였다. 실험으로부터 제품을 취출하여 다이 롤 높이를 측정하여 분석한 결과 기어 모듈과 관계없이 V-링 설치 위치가 가이드 플레이트에서 멀어짐에 따라 다이 롤 높이가 증가함을 파악할 수 있었다. 이와 같은 결과는 향후 파인 블랭킹 금형의 V-링을 설계할 때 다이 롤 높이를 최소화하기 위하여 유용하게 활용될 수 있을 것이다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.351-355
• /
• 2003

In this paper, a new barrier rib forming method of embossed barrier rib (EBR) formation process for the PDP rear panel was introduced. The process is mainly composed of green sheet fabrication, lamination of the green sheet on the rear glass panel having data electrodes, and roll embossing followed by firing. The EBR process has two advantages over the conventional barrier rib forming methods. One is the process requires less equipment investment than the conventional methods by about 20% of the current rear panel fabrication equipment investment owing to the simplified fabrication process. The other advantage is its reduced rear panel manufacturing cost by eliminating the time consuming and complicated processes and waste of materials in the conventional methods. In this study, general procedure of EBR fabrication process is described and the characteristics of prototype PDP using EBR panel are discussed.

• Laser Solutions
• /
• v.2 no.1
• /
• pp.51-60
• /
• 1999

In this paper, weldability and formability of Tailored-Blank (TB) and the structural impact testing of bump beam were investigated to apply TB to automobile bumper beam. The optimal $CO_2$ laser welding condition for TB of SPFC and SPRC steel plates with different thicknesses was obtained. Before welding, the cross section of butt joint was prepared only by shearing without milling process. Real type bump beam was produced by two kind of forming processes such as roll-forming and press-forming, and the good formability of TB was obtained. Impact test results of bump by using pendulum and barrier were satisfied the impact regulation of bump. Finally. It may be confirmed that laser welded TB is well-balanced material in both weight reduction and production cost of automobile bump.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.529-533
• /
• 2008

Thick pipes have been used in fields of ocean and industrial plants, and pipe arrangement of oil and water pipelines. Mostly, roll bending process has been used in manufacture of the pipes. Recently, however, studies on the pipe forming processes using brake press have been performed. Normally, the brake press has high aspect ratio, so structural integrity evaluation should be conducted. In this study, finite element analysis of structural integrity for the brake bending press was carried out for thick pipe forming process.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.740-745
• /
• 2001

The plastic deformation behavior of formed CICC fur the superconducting Tokamac fusion device was examined and appropriate manufacturing information was provided. A relation between travel of the bending roller and spring back displacement was obtained via virtual manufacturing. The radius of CICC after forming was expressed as a function of the bend-roll travel. The maximum von Mises stress after spring back was also monitored fur the SAGBO prediction. Next, the variation of the CICC cross-sectional area was examined during the first turn and during conduit bending with the largest curvature. Finally, the coil radius was measured and compared with the data generated from the virtual manufacturing. The measured data showed similar pattern as predicted one. Using the mapping function found to match with the real data, the data from the virtual manufacturing may facilitate accurate manufacturing.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.43-49
• /
• 2004

With building structures becoming higher and having longer spans, new structural steel with better strength, thicker plate, and performance may be required rather than conventional structural steel. TMC steel is widely used in building structures largely due to its excellent seismic performance, superior weldability, and design strength that is not affected by plate thickness. To make use of TMC steel in pipe structures with large diameter and heavy wall, however, the this study, the degradation of material properties in submerged are welded SM520TMC steel pipes and tubes was evaluated using variable fabrication process and material change. Degradation test results showed that the yield and ultimate strength increased and elongation decreased regardless of the mode of fabrication, i.e., through roll bending or press forming, or steel used, i.e., domestic SM520TMC steel or SM520TMC steel from Japan.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.7
• /
• pp.769-776
• /
• 2011

In order to cope with the requirements of smaller patterns, larger surfaces and lower costs in the fields of displays, optics and energy, greater attentions is now being paid to the development of micro-pattern machining technology. Compared with flat molds, roll molds have the advantages of short delivery, ease of manufacturing larger surfaces, and continuous molding. This paper presents the state-of-the-art of the micro pattern machining technology on the roll molds and introduces some research results on the machining process technology. The copper and nickel-phosphorous-alloy plating process, machining process technology for uniform micro patterns. micro cutting simulation and the real time monitoring system for micro machining are summarized. The developed technologies have led the complete localization of the prism sheets and will be applied to the direct forming process with succeeding research & development.