• 한국도로학회:학술대회논문집
• /
• 한국도로학회 2008년도 추계학술대회 논문집
• /
• pp.131-135
• /
• 2008

• International Journal of Automotive Technology
• /
• 제6권4호
• /
• pp.351-357
• /
• 2005

Development of a real-time simulation model for high-speed and multibody tracked vehicles is difficult because they involve hundreds of highly nonlinear equations. In the development of a reliable tracked vehicle model for real-time simulation, it is helpful to use an off-line tracked vehicle model developed by considering all the degrees of freedom of each element. This paper presents a step-by-step procedure for the development of a real-time simulation model based on the off-line tracked vehicle model. The road input data, Profile IV, is used for the real time simulation and simulation results are compared with vehicle test results obtained in the military test field. It is noted that the simulation results are quite close to the test results.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.211-219
• /
• 2003

The main study experiments to obtain engine torque of the vehicle during performance test of the recent automobile. Torque was measured through the engine dynamometer to produces engine torque of the vehicle but the research method calculated engine torque of the vehicle without the engine dynamometer. The performance of the vehicle receive various running resistance. The study certificates performance of certification before a certification of used vehicle didn't carry out and certificate. This way evaluated on road test and chassis dynamometer The result of the study shows that it is much possible to apply the test. After comparing the engine torque of road driving with that of chassis dynamometer, the results are approximately the same. When rapidly speeded up, the road-load vehicle can pitch in some degrees, which may result in the fluctuations of acceleration, and then affect on the engine torque. Therefore it is confirmed that this method is easier way to measure the performance of vehicles.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제13권4호
• /
• pp.269-276
• /
• 2013

Information and communication technology (ICT) is a promising solution for mitigating road traffic congestion. ICT allows road users and vehicles to be managed based on real-time road status information. In Tanzania, traffic congestion causes losses of TZS 655 billion per year. The main objective of this study was to develop an optimal approach for integrating real-time road information (RRI) to mitigate traffic congestion. Our research survey focused on three cities that are highly affected by traffic congestion, i.e., Arusha, Mwanza, and Dar es Salaam. The results showed that ICT is not yet utilized fully to solve road traffic congestion. Thus, we established a possible approach for Tanzania based on an analysis of road traffic data provided by organizations responsible for road traffic management and road users. Furthermore, we evaluated the available road information management techniques to test their suitability for use in Tanzania. Using the floating car data technique, fuzzy logic was implemented for real-time traffic level detection and decision making. Based on this solution, we propose a RRI system architecture, which considers the effective utilization of readily available communication technology in Tanzania.

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.177-185
• /
• 2013

PURPOSES : This study attempts to design and establish the road surface condition detection system by using the image processing that is expected to help implement the low-cost and high-efficiency road information detection system by examining technology trends in the field of road surface condition information detection and related case studies. METHODS : Adapted visual information collecting method(setting a stereo camera outside of the vehicle) and visual information algorithm(transform a Wavelet Transform, using the K-means clustering) Experiments and Analysis on Real-road, just as four states(Dry, Wet, Snow, Ice). RESULTS : Test results showed that detection rate of 95% or more was found under the wet road surface, and the detection rate of 85% or more in snowy road surface. However, the low detection rate of 30% was found under the icy road surface. CONCLUSIONS : As a method to improve the detection rate of the mobile road surface condition information detection system developed in this study, more accurate phase analysis in the image processing process was needed. If periodic synchronization through automatic settings of the camera according to weather or ambient light was not made at the time of image acquisition, a significant change in the values of polarization coefficients occurs.

• 조명전기설비학회논문지
• /
• 제24권3호
• /
• pp.1-7
• /
• 2010

To find an appropriate illuminance range for the disability glare caused by the road lighting system installed on guardrails, the influence of the disability glare was evaluated in comparison with the road lighting system of a streetlight. To test the disability glare, an indoor laboratory was constructed and a variation of luminance contrast threshold was evaluated. As a result, when the retinal illuminance was increased and glare sources existed within the narrow visual field, the luminance contrast threshold was increased. Although the road lighting luminaire was installed as low as the height of the guardrail on the road, when out of sight, the influence of the disability glare was small in comparison with the conventional road lighting system such as a streetlight.

• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.65-76
• /
• 2000

To measure the fuel consumption rate of a vehicle, a car is tested on chassis dynamometer following given driving mode. But the fuel consumption rate measured by this method may be somewhat different from that measured in on-road driving conditions. It may be due to not considering road grade in driving modes. In this study, new driving modes which include road grade are proposed, and the simulation program to estimate the real driving fuel consumption rate of a vehicle is developed. On-road car tests to verify the simulation program are carried out and the results of the simulation are analysed and compared with those of the experiments.

• 한국군사과학기술학회지
• /
• 제16권6호
• /
• pp.726-732
• /
• 2013

It is required for UGV(Unmanned Ground Vehicle) to have a LPP(Local Path Plan) component which generate a local path via the center of road by analyzing binary map to travel autonomously unpaved road in rough environment. In this paper, we present the method of boundary estimation for unpaved road and a local path planning method based on RANGER algorithm using the estimated boundary. In specially, the paper presents an approach to estimate road boundary and the selection method of candidate path to minimize the problem of zigzag driving based on Bayesian probability reasoning. Field test is conducted with scenarios in rough environment in which bush, tree and unpaved road are included and the performance of proposed method is validated.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.525-527
• /
• 2003

Recently, the spatial resolution of earth observation satellites is significantly increased to a few meters. Such high spatial resolution images definitely will provide lots of information for detail-thirsty remote sensing users. However, it is more difficult to develop automated image algorithms for automated image feature extraction and pattern recognition. In this study, we propose a two-stage procedure to extract road information from high resolution satellite images. At first stage, a watershed segmentation technique is developed to classify the image into various regions. Then, a knowledge is built for road and used to extract the road regions. In this study, we use panchromatic and multi-spectral images of the IKONOS satellite as test dataset. The experiment result shows that the proposed technique can generate suitable and meaningful road objects from high spatial resolution satellite images. Apparently, misclassified regions such as parking lots are recognized as road needed further refinement in future research.

• 한국도로학회논문집
• /
• 제8권3호
• /
• pp.115-127
• /
• 2006

현재 중부내륙 고속도로 시험도로(test road)에는 환경하중에 대한 도로 포장체의 환경적인 거동 특성을 파악하기 위하여 다져진 노상토에 WCR형태의 함수량계로 측정되는 체적 함수량이 현장 밀도의 영향등으로 부정확하게 예측되는 경향을 나타내고 있다. 따라서 본 연구에서는 흙의 특성과 현장 밀도를 고려하여 현장에 적합한 함수량 보정을 실내 및 현장시험을 각각 실시하고 이를 토대로 보정방정식을 제안하였다. 연구 결과 보정된 함수량은 현장의 측정치에 근접하게 판명되었다. 따라서 WCR을 활용하여 다짐된 노상토 지반의 체적 함수량을 측정시 사용된 흙의 종류 및 다짐조건 등이 고려되어야 한다.