• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.185-193
• /
• 2011

As a Lift axle is an additional axle installed mostly in heavy freight truck, It"s introduced for the purpose of cost saving, such as logistics, fuel, tire wear and prevention of the pavement damage. However, the Effects of a lift axle are anecdotal and they have occurred often that a lift axle is used improperly by expectations of some drivers. For these reasons, this study conducts a field experiment in order to identifying the change rate of fuel consumption due to an a Lift axle using, develops the fuel consumption model of field data, and then compares the effects of a Lift axle using through application of the model. As a result, fuel consumption decreased in loading conditions that are both empty and full when not using a lift axle.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.31-38
• /
• 2011

As the percentage of permeable ground is reduced due to the increased impermeable roads of major cities, a heat island phenomenon can be dominantly observed, resulting in increased temperature. In addition, rainfall that would have been naturally absorbed and retained by the permeable ground is overflowed due to large volumes of run-off water, resulting in more sewer failures and increased erosion. In terms of permeable pavement system, block paving has been used anywhere as well as provides many years of service. The permeable block paving is an effective alternative to the more traditional asphalt or plain concrete for minor roads; furthermore, it looks a lot better than other pavements. In this study, the functional drainage evaluation of block paving was carried out, considering the usage of experimental sludge and wheel tracking test, in order to simulate the field condition of roads.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.85-98
• /
• 2009

The in-situ Compaction test using sand cone (RC) and Plate Bearing Capacity Test (PBT) has been widely used for evaluating the subgrade and subbase condition on the pavement system. However, because the in-situ RC and PBT test are expensive and take plenties of time for operation, these are very difficult to figure out the in-situ characteristics of subgrade and subbase strength in detail. Therefore, for faster and economical operation, this study is to compare the Light Falling Weight Tests and propose the LFWD test as the in-situ Compaction test. This study suggests the relationship between in-situ RC value, $K_{30}$, $M_R$ and $E_{LFWD}$ of the subgrade and subbase materials in Korea using the laboratory and in-situ testing.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.15-26
• /
• 2008

Recently, various damages such as corrosion of rebar, scaling on concrete pavement and environmental deteriorations caused by using the chloride-containing deicer have been reported. To solve these problems, several substitute deicers have been developed by other researchers. However, studies on evaluation of performance for the developed deicers have been limited in the basic laboratory testing. It is necessary to establish the resonable and systematic test procedure for evaluating the deicing performance. In this study, rational and practical test methods were set up through literature review and deicing performance of Eco-Friendly Deicer(EFD), which is a kind of low chloride-containing deicer developed by our research group, was evaluated by the presented test methods. As results of the laboratory tests, initial deicing performance of EFD was similar with that of Pre-Wetted Salt(PWS) which has been used in highway deicing and it was verified by executed field tests in twice that EFD had passable deicing performance compare with PWS.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.115-124
• /
• 2008

This Study was investigated in main breakage types of 50 interlocking block pavements in apartment houses and evaluated on their performance. According to performance evaluation, maintenance control index of 9 aged interlocking block pavements ranged 7.9 to 8.9. These values meant that the condition of interlocking block pavements were still good. Therefore, it was concluded that the 10-year cycle of the block replacement recommended by Ministry of Construction & Transportation is necessary to reappraise. To objectively evaluate the performance of interlocking block pavements, this study presented the criteria of maintenance control by combining two maintenance control standards suggested by Ministry of Construction & Transportation and the Japan Interlocking Block Pavement Engineering Association. Also, this study suggested that the domestic standard is necessary to include durability standards and quality standards of joint filling materials and bedding sand layer for increasing expectation life and reducing maintenance costs of interlocking block pavements.

• International Journal of Highway Engineering
• /
• v.3 no.1 s.7
• /
• pp.177-184
• /
• 2001

A recycling agent has been manufactured on the basis of the chemical composition of reclaimed asphalt binders and virgin asphalt binders. The chemical compositions of reclaimed asphalt binders extracted from reclaimed asphalt pavements have been analyzed according to the ASTM method and the results were compared to those of virgin asphalt binder AP-3. Reclaimed asphalt binders have shown that asphaltenes was increased whereas saturates, naphthene aromatics, and polar aromatics fractions were decreased. A recycling agent made of aromatic compounds, in which its chemical composition is similar to the aromatics fraction in asphalt binders, has been produced to reduce the amount of asphaltenes in reclaimed asphalt hinders. The evaluation of the recycling agent produced was performed by testing ductility, rolling and ball softening point, penetration at $25^{\circ}C$ and viscosity at $60^{\circ}C$. It was found that, by adding the recycling agent 20% by weight to the reclaimed asphalt binders, the physical properties of reclaimed asphalt binders was recovered to the level of virgin asphalt binder AP-3.

• International Journal of Highway Engineering
• /
• v.3 no.1 s.7
• /
• pp.151-163
• /
• 2001

Very few studies have been attempted to understand the stress-strain behavior of flexible pavements reinforced with geosynthetics in the middle of asphalt layer. In this study, the flexible asphalt layer was analyzed with finite element method to understand stress-strain behavior. The asphalt layer was reinforced with glass grid and geogrid. The reinforcement was applied in the asphalt layer to prevent its excessive deformation and shear failure. The location of installation and stiffness of the geosynthetics were varied to obtain optimum depth of reinforcement and proper modulus. The results indicate that geosynthetics are more effective for reducing maximum shear stress than those of vertical stress and vertical displacement. Maximum shear stress decreased 15$\sim$20%, and glass grid with high value of modulus was the most effective. Also, in order to prevent failure of asphalt layer, reinforcement should be installed in the 3cm$\sim$5cm depth.

• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.63-71
• /
• 2005

Asphalt binder grading is to specify quality of asphalt binders relating to pavement performance in orderly manner, and provides the necessary information in selecting the appropriate asphalt binder for the hot mix design. For this purpose, United States has developed the PG-grading in 1995 and is implementing in practice. Recently, this American PG-grading system has been accepted as the domestic binder grading specification. However, the Asian (including Japan and China) and the most European countries are still use the traditional penetration and viscosity specification. The goal of this study lies in analysing the American PG-grading for its justification. As the result, the serious errors are found, and thus, to eliminate the errors, the more precise binder grading equation is introduced, Credibility of this study is checked by predicting the literature rut data with the equations mentioned. The prediction result are validating the claimes made in this study.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.9-20
• /
• 2011

Most of domestic expansion joint system was applied by exposed expansion joint system. There are cases where it is damaged by driving. As the result noise and impact happened, and the social cost due to frequent repair works is increasing. So based on the Asphalt Plug Joint(APJ) system that applied in the United States and Europe, new buried expansion joint system was lately developed a system of Buried Folding Lattice Joint(BFLJ) that changed substructure. In this research, we have tested for durability and flexibility performance of buried expansion joint system that based on the type of asphalt mixture. Also we have evaluated for durability of BFLJ system against vehicle load using accelerated pavement testing. As a result of the experiment, the developed BFLJ system gives high flexibility performance and resolves transformation concentration along the joint section more than APJ system. Also it could be seen that the BFLJ system could overcome the disadvantages of APJ and prevent early damage. Because surface deflection of BFLJ system against vehicle load was measured low, and sub system in the buried expansion joint system was not damaged against vehicle load.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.1-8
• /
• 2011

The objective of this paper is to evaluate the performance of low $CO_2$ asphalt binder properties using LEADCAP$^{(R)}$(Low Energy and Carbon Asphalt Pavement) additive as function of various aging methods such as RTFO(Rolling thin film oven), Ultraviolet(UV) lay. In order to simulate the short-term aging of asphalt binder that occurs during the hot-mixing asphalt process, the Rolling Thin Film Oven(RTFO) was used. Asphalt binder using LEADCAP$^{(R)}$ is prepared by addition of a photoinitiator activated by ultraviolet lay. The mechanical and rheological properties of the asphalt binder were estimated using UTM(Universal Testing Machine) and DSR(Dynamic Shear Rheometer). The test results showed that the asphalt binder using LEADCAP$^{(R)}$ additive was improved the rutting resistance at testing temperature ($70^{\circ}C$) and increased tensile strength at low temperature. Also, Thermal analysis shows that the Melting Point(Tm) of asphalt binder using LEADCAP$^{(R)}$ additive was constant although the asphalt binder was aged by Ultraviolet.