• 제목/요약/키워드: ribs

검색결과 814건 처리시간 0.028초

Rib의 형상에 따른 heat spreader의 열전달 특성 (Heat Transfer Characteristics of PDP Heat Spreader with Various Rib Types)

  • 김재중;이창희;백승준;신승훈;장석원;유동수;노홍구
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2001년도 춘계학술대회논문집D
    • /
    • pp.402-407
    • /
    • 2001
  • This paper reports a result of numerical heat transfer analysis for heat spreader with various ribs. Four different ribs are compared in this study. In general, the heat transfer on a vertical plate is enhanced when a rib is attached as the surface area increases, and the growth of the boundary layer is interrupted. However, for a low flow less than 0.1m/s, it is observed that the heat transfer is sensitive to the height of a rib: it decreases as the height increases. Among the four ribs, the H-shaped rib showed better performance than other ribs.

  • PDF

터널지보재로서 격자지보(Lattice Girder)의 현장적용성 평가 연구 (Evaluation of an applicability of lattice girders for the tunnel support)

  • 문홍득;이성원;배규진
    • 터널과지하공간
    • /
    • 제6권2호
    • /
    • pp.122-130
    • /
    • 1996
  • Generally the NATM technique uses shotcrete, rock bolts, H-beam steel ribs, and concrete lining for the tunnel support in Korea. Among them, H-beam steel ribs are extremely heavy and difficult for workers to handle. Therefore, especially in Europe, lattice girders are being used instead of H-beam steel ribs for tunnel support. Lattice girders have basically the same function as H-beam steel ribs in tunnelling. The main advantages of using lattice girders compared to H-beam steel rib supports are as follows: 1) lattice girders have relatively a low weight enough to be easily lifted and installed by labors and 2) they create a more effective bond with the shotcrete. The purpose of this study is to evaluate the effectiveness and applicability of lattice girders compared to H-beam steel ribs used in construction tunnel sites and to show that lattice girders can be adequately applied in domestic tunnel construction sites as a new tunnel support system.

  • PDF

수용성 UV경화성 수지를 이용한 고품질 PDP용 격벽제작 기술 개발 (Development of High-definition PDP(Plasma Display Panel) Barrier Ribs Using Watersoluble UV-curing Resin)

  • 남수용;우진호;이미영;이갑희;김광영
    • 한국인쇄학회지
    • /
    • 제21권2호
    • /
    • pp.67-74
    • /
    • 2003
  • Barrier ribs for PDP(plasma display panel) are commonly utilized to have uniform height and width and to prevent opical crosstalk between adjacent cells. The requirements for such barrier ribs are uniform height and shape, low outgassing rate and low porosity, high aspect ratio, and fine resolution. In this study, we are studied about that to make efficiency of material and high quality barrier ribs for PDP. As a result, could got high barrier ribs of $140{\mu}m$ evenly in 1th phenomenon using watersoluble UV curing resin and know that flatness of upper part is also very good.

  • PDF

Transparent Plasma Display using Transparent Glass Barrier Ribs

  • Lee, Sung-Min;Kim, Seung-Hun;Oh, Seung-Hwa;Shin, Bhum-Jae;Choi, Kyung-Cheol
    • 한국정보디스플레이학회:학술대회논문집
    • /
    • 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
    • /
    • pp.339-341
    • /
    • 2009
  • A transparent plasma display was developed using transparent glass barrier ribs. Glass barrier ribs were fabricated via a wet etching process. Glass barrier ribs created using a top and bottom etching process showed better transparency compared to those created through only a top etching process. A see-through phosphor layer was obtained by coating the sidewall of the barrier ribs with a conventional opaque phosphor. A fabricated prototype of a transparent plasma display was clear enough to see the background beyond the panel and was well operated by a conventional driving scheme. The maximum luminance was 1150 cd/$m^2$ and the maximum luminous efficacy was 1.35 lm/W in a Ne+13.5%Xe gas-mixture and green cells.

  • PDF

대형항공기 날개 리브 가공을 위한 자동화 공정 시뮬레이션 (Method to Simulate the Automatic Processing of Large Aircraft Wing Ribs)

  • 송철기;이대건;이창범;김갑순
    • 한국기계가공학회지
    • /
    • 제19권9호
    • /
    • pp.85-92
    • /
    • 2020
  • In this study, the automatic processing of the wing ribs of large aircraft was simulated. Specifically, in the simulation for the automatic processing of the fly ribs, the process of the automated loading device with a robot was examined, along with the wing rib processing and manufacturing automation processes. Moreover, the process time, corresponding to all the stages in the wing rib processing, was calculated. The results pertaining to the machining and manufacturing times of 34 wing ribs (Nos. 1-17), as obtained through the proposed simulation approach, indicated that the total machining time for the left and right wing ribs and rib guns was 537.7 h. The production time was calculated as 1,117.4 h. It is considered that the processing of the wing ribs of large aircraft can be automated in a factory, based on the results of the proposed simulation process.

사각 덕트내 요철의 각도 변화에 따른 열전달 특성 (Augmented heat transfer in a rectangular duct with angled ribs)

  • 우성제;김완식;조형희
    • 대한기계학회논문집B
    • /
    • 제22권4호
    • /
    • pp.530-541
    • /
    • 1998
  • Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass transfer coefficients. Downwash of the rotating secondary flow, reattachment of main flow between ribs and the vortices near ribs and wall enhanced the mass transfer locally up to 8 times of that in case of the duct without ribs.

Buckling Strength Increment of Curved Panels Due to Rotational Stiffness of Closed-Section Ribs Under Uniaxial Compression

  • Andico, Arriane Nicole P.;Park, Yong-Myung;Choi, Byung H.
    • 국제강구조저널
    • /
    • 제18권4호
    • /
    • pp.1363-1372
    • /
    • 2018
  • Recently, there have been studies about the increasing effect on the local plate buckling strength of flat plates when longitudinally stiffened with closed-section ribs and an approximate solution to quantitatively estimate these effects were suggested for flat plates. Since there are few studies to utilize such increasing effect on curved panels and a proper design method is not proposed, thus, this study aims to numerically evaluate such effect due to the rotational stiffness of closed-section ribs on curved panels and to propose an approximate method for estimating the buckling strength. Three-dimensional finite element models were set up using a general structural analysis program ABAQUS and a series of parametric numerical analyses were conducted in order to examine the variation of buckling stresses along with the rotational stiffness of closed-section ribs. By using a methodology that combine the strength increment factor due to the restraining effect by closed-section ribs and the buckling coefficient of the panel curvature, the approximate solutions for the estimation of buckling strength were suggested. The validity of the proposed methods was verified through a comparative study with the numerical analysis results.

리브 형상 및 개수에 따른 사각플라스틱 페트병의 강성보강에 관한 연구 (A study of Improvement of Stiffness for Plastic PET bottle with Different Geometries and Numbers of Rib)

  • 이영훈;박범진;정의철;오정길;홍석관
    • Design & Manufacturing
    • /
    • 제17권4호
    • /
    • pp.33-41
    • /
    • 2023
  • Excessive use of plastic bottles contributes to a significant environmental issue due to the high volume of plastic waste generated. To address this, efforts are needed to reduce the weight of plastic bottles. However, indiscriminate weight reduction may compromise the essential rigidity required for plastic bottles. Extensive research on rib shape for pressure vessels are exists, but there is a few research of rib shapes to enhance the stiffness of plastic bottles. The following results were obtained from the analyses conducted in this study. 1) Among the rib cross-sections of square, trapezoid, and triangle, the buckling critical load of PET bottles with square-shaped ribs is improved by about 14% compared to the buckling critical load of PET bottles without ribs. 2) The buckling critical load is improved by about 18% when a square-shaped rib with an aspect ratio of 0.2 is applied, compared to the buckling critical load of the bottle without the rib. 3) When longitudinal and transverse square ribs were applied to the axial direction of the PET bottle, the buckling critical load was improved by about 32% and 58% compared to the buckling critical load of the PET bottle without ribs, respectively, indicating that applying longitudinal ribs is effective in reinforcing the stiffness of PET bottles. 4) When 14 transverse ribs were applied, the maximum improvement was about 48% compared to the buckling critical load of the plastic bottle without ribs. 5) When 3 longitudinal ribs were applied on each side, the maximum improvement was about 76% compared to the buckling critical load of the bottle without ribs. Therefore, it was concluded that for effective stiffness reinforcement of a 500ml square bottle with a thickness of 0.5mm, 3 square-shaped ribs with an aspect ratio of 0.2 should be applied in the longitudinal direction relative to the axial direction of the bottle.

사각 채널에 설치된 테이프가 열전달과 마찰계수에 미치는 효과 (Effects of Tape on Heat Transfer and Friction Factor in a Square Channel)

  • 안수환;강호근;배성택;아리바시아크리시나 부트라
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2007년도 춘계학술대회B
    • /
    • pp.2402-2407
    • /
    • 2007
  • Heat transfer distributions and friction factors in square channels (3.5 ${\times}$ 3.5 cm) with twisted tape inserts and with twisted tape inserts plus interrupted ribs are respectively investigated. Tests are performed for Reynolds numbers ranging from 8,900 to 29,000. The rib height-to-channel hydraulic diameter, e/Dh, is kept at 0.057 and test section length-to-hydraulic diameter, L/Dh is 30. The twisted tape is 0.1 mm thick carbon steel sheet with diameter of 3.3cm, length of 90cm, and 2.5 turns. The square ribs are arranged to follow the trace of the twisted tape and along the flow direction defined as axial interrupted ribs. Each wall of the square channel is composed of isolated aluminum sections. The following conclusions from the experimental study were drawn as: 1) In the 4 heating wall channel with twisted tape inserts, Nusselt number based on bottom wall temperature is enhanced by 1.2 - 1.6 times if adding the axial interrupted ribs on the bottom wall only. 2) The twisted tape with interrupted ribs under the two-sided heating condition produces the highest heat transfer performance. 3) Friction factor data obtained for the square channel with twisted tape inserts plus axial interrupted ribs are less than those in the past publications for circular tubes with axial interrupted ribs and twisted tape inserts.

  • PDF

새로운 형태의 리브를 갖는 보강판의 좌굴거동 (Buckling Behavior of Plates Stiffened with the New Type Ribs)

  • 주석범;이필남
    • 한국강구조학회 논문집
    • /
    • 제30권1호
    • /
    • pp.59-66
    • /
    • 2018
  • 본 연구에서는 새로운 형태의 리브(${\Box}$형)를 갖는 보강판의 좌굴거동에 대한 매개변수 해석을 수행하였다. ${\Box}$형 리브의 제원에 따른 좌굴능력의 변화가 일정한 양상을 나타냄에 따라 특정 좌굴하중을 갖는 ${\Box}$형 리브 단면을 구하는 시스템을 제안할 수 있었으며, 이 시스템을 실교량의 강바닥판에 적용하였을 때 기존 폐단면 리브보다 더 경제적인 ${\Box}$형 리브 단면을 많이 얻을 수 있었다. 따라서 본 연구에서 제안한 ${\Box}$형 리브 시스템을 이용하면, 소요 좌굴 능력을 가지면서도 보다 경제적인 강바닥판 설계를 할 수 있을 것으로 판단된다.