• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.59-65
• /
• 2019

In this study, optimal design of direct-drive VCMs (Voice Coil Motor) for a missile fin actuator is carried out. The torque performance and the characteristics of the VCM are predicted by commercial electromagnetic analysis software, ANSYS Maxwell. The optimal design is obtained at the minimum and maximum actuating angles where the aerodynamic load acting on the fin is the largest in the operating range. The critical variables of the actuator is designed and the RSM (Response Surface Method) is used for the optimization. The response surface model consists of second-order functions and its experimental points are selected by a central composite design. This design is widely used for fitting a second-order response surface. The adjustment regression coefficients is computed for adequacy checking of the response surface model. Finally, the torque values obtained by the RSM and the ANSYS Maxwell are shown in good agreement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.957-960
• /
• 2006

In order to predict the accumulated damages by cyclic freeze-thaw, a regression analysis by the Response Surface Method (RSM) is used. RSM has merits when the other probabilistic simulation techniques can not guarantee the convergence of probability of occurrence or when the others can not differentiate the derivative terms of limit state functions, which are composed of random design variables in the model of complex system or the system having higher reliability. For composing limit state function, the important parameters for cyclic freeze-thaw-deterioration of concrete structures, such as water to cement ratio, entrained air pores, and the number of cycles of freezing and thawing, are used as input parameters of RSM. The predicted results of relative dynamic modulus and residual strains after 300 cycles of freeze-thaw for specimens show very good agreements with the experimental results. The RSM result can be used to predict the probability of occurrence for designer specified critical values. Therefore, it is possible to evaluate the life cycle management of concrete structures considering the accumulated damages by the cyclic freeze-thaw by the use of proposed prediction method.

• Korean Journal of Food Science and Technology
• /
• v.29 no.4
• /
• pp.752-757
• /
• 1997

Crude papain extracted at optimum condition was purified with an ethanol precipitation method. Four factors of protein recovery method were optimized by response surface methodology (RSM) and the function was expressed in terms of a quadratic polynomial equation. Adequacy of the model equation for optimum response values was tested and optimum conditions of protein recovery were 38.2 mg/mL of protein, ethanol concentration of 40% and precipitation temperature of $-8^{\circ}C$. The experimental value (68.97%) for recovery yield was closed to the predicted value (77.28%) under these conditions.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2384-2389
• /
• 2007

The 2nd order response surface method (RSM) has been carried out to get optimum thermal design for enhanced heat transfer on square channel with bleed holes. The RSM was used as an optimization technique with Reynolds-averaged navier-stokes equation. Turbulence model for heat transfer analysis used RNG k-epsilon model. The wall function used enhanced wall function. Numerical local heat transfer coefficients were similar to the experimental tendency. Two design variables such as attack angle of rib (${\alpha}$), rib pitch-to-rib height ratio (p/e) were chosen. Operation condition considered bleeding ratio per bleed hole ($BR_{hole}$). A response surface were constructed by the design variables and operation condition. As a result, adjusted $R^2$ was more than 0.9. Optimization results of various objective function were similar to heat transfer in channel with and without bleed flow. But friction factor was lower than channel without bleed flow.

• Computational Structural Engineering
• /
• v.7 no.1
• /
• pp.109-116
• /
• 1994

In this paper, various reliability analysis methods for calculating a probability of failure are investigated for their accuracy and efficiency. Crude Monte Carlo method is used as a basis for the comparison of various numerical results. For the sampling methods, Importance Sampling method and Directional Simulation method are considered for overcoming a drawback of Crude Monte Carlo method. For the approximate methods, conventional Rackwitz-Fiessler method. 3-parameter Chen-Lind method, and Rosenblatt transformation method are compared on the basis of First order reliability method. As a Second-order reliability method, Curvature-Fitting paraboloid method, Point-fitting paraboloid method, and Log-likelihood function method are explored in order to verify the accuracy of the reliability calculation results. These methods mentioned above would have some difficulty unless the limit state equation is expressed explicitly in terms of random design variables. Thus, there is a need to develop some general reliability methods for the case where an implicit limit state equation is given. For this purpose, Response surface method is used where the limit state equation is approximated by regression analysis of the response surface outcomes resulted from the structural analysis. From the application of these various reliability methods to three examples, it is found that Directional Simulation method and Response Surface method are very efficient and recommendable for the general reliability analysis problem cases.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.510-515
• /
• 2004

A proton exchange membrane fuel cells(PEMFC) operate at low temperature, allowing for faster startups and immediate response to change in the demand for power, and also deliver high power density. To maximize economical efficiency in PEMPC, it is necessary to the optimization. Response surface method(RSM) has non-gradient and fast convergency characteristics. Sampling points are extracted by design of experiments using Central Composite Method. In this paper, it is shown that the optimization is required for the design study of the PEMFC.

• Journal of Mechanical Science and Technology
• /
• v.18 no.10
• /
• pp.1829-1836
• /
• 2004

This study presents the performance optimization of hypervelocity launcher system by using the experimentall data. During the optimization, the RSM (Response Surface Method) is adopted to find the operating parameters that could maximize the projectile speed. To construct a reliable response surface model, 3 full factorial method is used with the selected design variables, such as piston mass and 2 driver fill pressure. Nine test data could successfully construct the reasonable response surface, which used to yield the optimal operational conditions of the system using the genetic algorithm. The optimization results are confirmed by the experimental test with a good accuracy. Thus, the optimization can improve the performance of the facility.

• Journal of Animal Science and Technology
• /
• v.53 no.3
• /
• pp.253-259
• /
• 2011

The aim of this work was to determine the method and predict the optimum conditions for egg quality stored for 7 days when combination treatments of irradiation and chitosan coating were applied using response surface methodology (RSM). A central composite design was chosen for the RSM in this study and the factors were irradiation dose (0~2 kGy) and concentration of chitosan coating material (0~2%). Performance of the irradiation and chitosan coating were evaluated by analyzing the egg quality and functional property factors. The predicted maximum level of Haugh units and foaming ability calculated by a developed model were 74.19 at 0 kGy of irradiation with coating by 0.96% chitosan solution and 50.83 mm at 2.0 kGy with 1.01%, respectively. The predicted minimum value of foam stability and 2-thiobarbituric acid reactive substances (TBARS) value were 2.97 mm at 0.39 kGy with 0.21% and 0.54 mg malonaldehyde/kg egg yolk at 0 kGy with 0.90% of chitosan solution, respectively. Results clearly showed that gamma irradiation negatively affected the Haugh unit and TBARS but positively affected the foaming capacity. The estimated value from the developed model by RSM was verified by no statistical difference with observed value. Therefore, RSM can be a good tool for optimization and prediction of egg quality when 2 or more treatments are combined. However, one should decide the target quality first to achieve a successful implementation of this technology.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.92-99
• /
• 2007

In this paper, optimization of the vaned centrifugal compressor was carried out at a given mass flow rate condition. Firstly, impeller optimization was conducted using response surface method (RSM) which is one of optimization methods. After the optimization of the impeller was completed, diffuser optimization was performed with the optimized impeller. In these processes, Navier-Stokes solver was used to calculate the flow inside the centrifugal compressor. And the optimization is performed with Box-Behnken design method which is efficient for fitting second-order response surfaces to reduce the number of calculations required. As a result, compared with the reference model, the efficiency and the pressure ratio of the optimized impeller and diffuser are found to be increased. The performance at off-design conditions is presented.

• Journal of the Korean Society of Visualization
• /
• v.7 no.2
• /
• pp.47-55
• /
• 2010

In this study, we optimized the shape of the surface aerator that will be installed in a biological reactor using the response surface method. Response surfaces of mass flow rate, impeller torque, mass flow rate per impeller torque are generated and used to track the optimum shape of the aerator. MOGA(Multi-Objective Genetic Algorithm)method is adopted to find the optimum results. By increasing the mass flow rate per impeller torque, increase of oxygen supply efficiency to a reactor is anticipated. To verify the usability of the surface aerator, PIV measurements on flow fields inside a scale-downed biological reactor model are carried out.