• Journal of Adhesion and Interface
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2003

In this work, the effect of PMR-15 content on the variation of surface free energy of the DGEBA/PMR-15 blend system was investigated in terms of contact angles and mechanical interfacial tests. Based on FT-IR result of the blend system. C=O (1,772, $1,778cm^{-1}$) and C-N ($1,372cm^{-1}$) peaks appeared with imidization of PMR-15 and -OH ($3,500cm^{-1}$) peak showed broadly at 10 phr of PMR-15 by ring-opening of epoxy. Contact angle measurements were performed by using deionized water and diiodomethane as testing liquids. As a result, the surface free energy of the blends gave a maximum value at 10 phr of PMR-15, due to the significant increasing of specific component. The mechanical interfacial properties measured from the critical stress intensity factor ($K_{IC}$) and the critical strain energy release rate ($G_{IC}$) showed a similar behavior with the results of surface energetics. This behavior was probably attributed to The improving of the interfacial adhesion between intermolecules, resulting from increasing the hydrogen bondings of the blends.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.1
• /
• pp.35-44
• /
• 2004

The water soluble fractions(WSF) from Japanese larch wood were isolated, purified by anion exchange resin and Sephadex gel filtration and identified its chemical structure by means of periodate oxidation and methylation reactions. Its major components are arabinose and galactose (1 : 3.4). Based on the results of periodate oxidation, methylation and gas chromatographic analysis of purified WSF, main chain is composed of β-1,3-glycosidic linkage among D-galactopyranoses, and two different side chains; β-1,6-glycosidic linkage among 2-3 units of D-galactopyranoses and β-1,6-glycosidic linkage between 1-2 units of D-galactopyranose and L-arabinopyranose. Addition of WSF to culture media of oak mushroom (Lentinula edodes) accelerated the mycelial growth. In the case of PDA cultures, 2 percent addition of WSF in Sanlim No. 6 strain and 4 percent of WSF in Mok-H strain mostly enhanced the mycelial growth of the mushroom. In the case of sawdust cultures, 4 percent addition of WSF in two strains showed the best mycelial growth. High percentages addition of WSF inhibited mycelial growth of the mushroom. Mushroom production was increased with addition of WSF. By the addition of WSF, ergosterol contents in the media were quite high at the colonized stage and rapidly increased at the fruiting stage. Therefore the ergosterol content could be utilized as an indicator to evaluate the culture maturity for the mushroom fruiting.

• Composites Research
• /
• v.37 no.2
• /
• pp.59-67
• /
• 2024

Research was conducted on a PA material-based composite material manufacturing method for application to engine mount brackets. Engine mount brackets must have heat resistance, impact resistance, and damping performance. PA66 resin was used as the base material for the composite material. The glass fiber was used as the reinforcement material. The composite material was manufactured using the injection molding method. The thermal, mechanical, and morphological characteristics were analyzed depending on the content of glass fiber. 3D model was created using the property evaluation database of composite materials(input data). The damping performance of the generated 3D model was extracted as out-put data. The reason for evaluating the characteristics of PA-based composite materials and conducting simulations on the damping performance of 3D models of engine brackets is because product performance can be predicted without manufacturing actual automobile parts and conducting damping performance tests. As a result of the damping simulation, damping performance tended to increase proportionally as the mass fraction of the reinforcement increased. But above a certain level, it no longer increased and slightly decreased. As a result of comparing the actual experimental values a nd the simulated values, the approximate value was within ±5%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.4
• /
• pp.220-227
• /
• 2004

Phosphorus desorption study is essential to understanding P behavior in agricultural and environmental soils because phosphorus is considered as two different aspects, a plant nutrient versus an environmental contaminant. This study was conducted to determine soil P buffering power related to P desorption quantity intensity (Q/I) parameters, $Q_{max}$(an index of P release capacity) and $l_0$(an index of the intensity factor), and to investigate the characteristics of relationship between the P desorption Q/I parameters and the soil properties. Soil samples were prepared with treatments of 0 and $100mg\;P\;kg^{-1}$ applied as $KH_2PO_4$ solution. The P desorption Q/I curves were obtained by a procedure using anion exchange resin beads and described by an empirical equation ($Q=aI^{-1}+bln(I+1)+c$). The P desorption Q/I curves for the high available P (${\g}20mg\;kg^{-1}$ of Olsen P) soils were characteristic concave trends with or without soil P enrichment, whereas for the low available P (${\lt}20mg\;kg^{-1}$ of Olsen P) soils, the anticipated Q/I concave curves could not be obtained without a proper amount of P addition. When the soils were enriched in phosphates, the values of desorbed solid phase labile P and solution P, such as $Q_{max}$ and $I_0$ respectively, were increased, but the ratio of $Q_{max}$ versus $I_0$ was decreased. Thus, the slope of desorption Q/I curve represented as phosphorus buffering power, $|BP_0|$, is decreased. The $|BP_0|$ values of the high available P soils ranged between 48 and $61L\;kg^{-1}$ in the P untreated samples and between 18 and $44L\;kg^{-1}$ in the P enriched samples. Overall $|BP_0|$ values of both low and high available P soils treated with $l00mg\;P\;kg^{-1}$ ranged between 14 and $79L\;kg^{-1}$. The $Q_{max}$, values ranged between 71.4 and $173.1mg\;P\;kg^{-1}$, and the lo values ranged between 0.98 and $3.82mg\;P\;L^{-1}$ in the P enriched soils. The $Q_{max}$ and $I_0$ values that control the P buffering power may be not specifically related to a specific soil property, but those values were complicatedly related to soil pH, clay content, soil organic matter content, and lime. Also, phosphorus release activity, however, markedly depended on the desorbability of the applied P as well as the native labile P.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.9
• /
• pp.1013-1019
• /
• 2007

Electronic wastes have increased tremendously. However, any reliable treatment methodologies have rarely been established. Electronic wastes have posed serious disposal problem due to their physico-chemical stability. This paper investigated the application possibility of pyrolysis for the purpose of recycling the p-CCL(phenol based Copper Clad Laminate). Thermogravimetric analysis(TGA) was used to investigate the thermal decomposition pattern of p-CCL. We elucidated the characteristics of pyrolysis by-products at operating temperatures of 280, 350 and $600^{\circ}C$. GC/MS and FT-IR were used to characterize the liquid by-products along with general characterization methods such as Ultimate Analysis, Proximate Analysis and Heating Value, whereas general characterization methods were only introduced for the solid by-products. At a heating rate of $5^{\circ}C$/min, TGA curves exhibited three decomposition stages: (1) low-temperature decomposition region$(<280^{\circ}C)$, (2) medium temperature region$(280\sim350^{\circ}C)$ and (3) high-temperature region$(>350^{\circ}C)$. The major compounds of liquid by-products at low- and medium-temperatures were accounted for by water and phenol, whereas branched phenols and furans were major compounds at high-temperatures. As the temperature increases, volatile quantities decreased but the fixed carbon increased. High heating values of solid by-products($7,400\sim7,600$ kcal/kg) would suggest that the solid by-products could be applicable as fuel. In addition, high fixed carbon but low ash content of the solid by-products offered an implication that they are capable of being upgradable for adsorbent after applying appropriate activating process.

• Journal of Korean Society of Forest Science
• /
• v.83 no.4
• /
• pp.486-497
• /
• 1994

The objective of this study was to examine the effects of air pollution on Pinus thunbergii forests surrounding Sasang industrial complex in Korea. The injury index, contents of chlorophyll and mineral elements, and concentrations of water soluble sulfur in needles were investigated at sample plots surrounding industrial complex and compared with those of control far from industrial complex. The results obtained are as follows ; 1. Discoloration of Pinus thunbergii needles was severe in the vicinity of industrial complex, and the older needle age classes was the more severe its injury appeared. Injury index was increased in the vicinity of industrial complex. 2. Water-soluble sulfur concentration was high in the vicinity of industrial complex at all of needle age classes, and those of all plots were higher than that of control. 3. Chlorophyll a contents were lower at surrounding industrial complex than that at control. It was supposed that chlorophyll a was destroyed by air pollutants. Total chlorophyll contents and content ratio of chlorophyll a to b were influenced by decrease of chlorophyll a contents. 4. Phosphorus contents in needles were decreased even in remoted regions with the increase of needle age classes. Colcium contents in needles were decreased near industrial complex at all needle ages classes. 5. There were negative correlation, between injury index and chlorophyll contents, injury index and calcium contents, and there were positive correlation between injury index and calcium contents. 6. Cluster analysis was carried out to divide the injured regions on sample plots. As a result of the analysis, there were devided 3 regions, severe regions(1-8 plots), medium regions(9, 10, 11, 12, 15, 17 plot), slight(13, 14, 16, 18, 19 plot and control). 7. The cross section of visible injured needle showed the destruction of mesophyll cell, sclerenchyma cell in the outside of resin duct and endodermis, partially.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.468-474
• /
• 1993

A dehydrating sheet comprises polymeric water absorber. which are packed in a semipermeable cellophane film bag allowing selective permeation of water. This sheet dehydration is quite different from conventional drying method such as sun drying, hot-air blast drying and cold air blast drying in a sense that samples are dried without heat treatment. As a part of the studies to develope a new processing method for effective utilization of dark muscle fishes, the preparation of a good quality salted and semi-dried mackerel by the dehydrating sheet was attempted. The dehydration time for preparation of a salted and semi-dried mackerels containing approximately equal moisture content were revealed $180{\sim}510min$ in conventional drying method and $90{\sim}160min$ in this sheet dehydration, respectively. The moisture and histamine contents of those salted and semi-dried mackerels were $59.4{\sim}62.4%$ and $2.5{\sim}3.6 mg/100g$, respectively. The changes in peroxide value, fatty acid composition, brown pigment formation, myofibrillar protein solubility and Ca-ATPase activity during processing of the salted and semi-dried mackerel prepared by the sheet dehydration were more lower than those of products prepared by conventional drying methods. Therefore, these result showed that the quality of a salted and semi-dried mackerel prepared by the sheet dehydration was imperial to that of those products by conventional drying method.

• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.51-60
• /
• 2009

The purpose of this study was to perform quantitative comparisons of water permeable zones in both the adhesive and the hybrid layer before and after thermo cycling in order to assess the integrity of the bonding interface. Twenty eight flat dentin surfaces were bonded with a light-cured composite resin using one of four commercial adhesives [OptiBond FL (OP), AdheSE (AD), Clearfil SE Bond (CL). and Xeno III (XE)]. These were sectioned into halves and subsequently cut to yield 2-mm thick specimens; one specimen for control and the other subjected to thermocycling for 10,000 cycles. After specimens were immersed in ammoniacal silver nitrate for 24 h and exposed to a photo developing solution for 8 h, the bonded interface was analyzed by scanning electron microscopy (SEM) and wavelength dispersive spectrometry (WDS) at five locations per specimen. Immediately after bonding. the adhesive layer of OP showed the lowest silver uptake, followed by CL, AD. and XE in ascending order (p < 0.0001); the hybrid layer of CL had the lowest silver content among the groups (p = 0.0039). After thermocycling, none of the adhesives manifested a significant increase of silver in either the adhesive or the hybrid layer. SEM demonstrated the characteristic silver penetrated patterns within the interface. It was observed that integrity of bonding was well maintained in OP and CL throughout the thermocycling process. Adhesive-tooth interfaces are vulnerable to hydrolytic degradation and its permeability varies in different adhesive systems, which may be clinically related to the restoration longevity.

• Journal of Radiation Protection and Research
• /
• v.33 no.1
• /
• pp.13-20
• /
• 2008

The flow rate measurements in a multi-phase flow pipeline were evaluated quantitatively by means of a clamp-on sealed radioisotope based on a cross correlation signal processing technique. The flow rates were calculated by a determination of the transit time between two sealed gamma sources by using a cross correlation function following FFT filtering, then corrected with vapor fraction in the pipeline which was measured by the ${\gamma}$-ray attenuation method. The pipeline model was manufactured by acrylic resin(ID. 8 cm, L=3.5 m, t=10 mm), and the multi-phase flow patterns were realized by an injection of compressed $N_2$ gas. Two sealed gamma sources of $^{137}Cs$ (E=0.662 MeV, ${\Gamma}$ $factor=0.326\;R{\cdot}h^{-1}{\cdot}m^2{\cdot}Ci^{-1}$) of 20 mCi and 17 mCi, and radiation detectors of $2"{\times}2"$ NaI(Tl) scintillation counter (Eberline, SP-3) were used for this study. Under the given conditions(the distance between two sources: 4D(D; inner diameter), N/S ratio: $0.12{\sim}0.15$, sampling time ${\Delta}t$: 4msec), the measured flow rates showed the maximum. relative error of 1.7 % when compared to the real ones through the vapor content corrections($6.1\;%{\sim}9.2\;%$). From a subsequent experiment, it was proven that the closer the distance between the two sealed sources is, the more precise the measured flow rates are. Provided additional studies related to the selection of radioisotopes their activity, and an optimization of the experimental geometry are carried out, it is anticipated that a radioisotope application for flow rate measurements can be used as an important tool for monitoring multi-phase facilities belonging to petrochemical and refinery industries and contributes economically in the light of maintenance and control of them.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.56-65
• /
• 2022

Copper is one of the non-ferrous metals used in the electrical/electronic manufacturing industries due to its superior properties particularly the high conductivity and less resistivity. The effluent generated from the surface finishing process of these industries contains higher copper content which gets discharged in to water bodies directly or indirectly. This causes severe environmental pollution and also results in loss of an important valuable metal. To overcome this issue, continuous R & D activities are going on across the globe in adsorption area with the purpose of finding an efficient, low cost and ecofriendly adsorbent. In view of the above, present investigation was made to compare the performance of a plant root (Datura root powder) as a bio-adsorbent to that of the synthetic one (Tulsion T-42) for copper adsorption from such effluent. Experiments were carried out in batch studies to optimize parameters such as adsorbent dose, contact time, pH, feed concentration, etc. Results of the batch experiments indicate that 0.2 g of Datura root powder and 0.1 g of Tulsion T-42 showed 95% copper adsorption from an initial feed/solution of 100 ppm Cu at pH 4 in contact time of 15 and 30 min, respectively. Adsorption data for both the adsorbents were fitted well to the Freundlich isotherm. Experimental results were also validated with the kinetic model, which showed that the adsorption of copper followed pseudo-second order rate expression for the both adsorbents. Overall result demonstrates that the bio-adsorbent tested has a potential applicability for metal recovery from the waste solutions/effluents of metal finishing units. In view of the requirements of commercial viability and minimal environmental damage there from, Datura root powder being an effective material for metal uptake, may prove to be a feasible adsorbent for copper recovery after the necessary scale-up studies.