• Journal of applied mathematics & informatics
• /
• 제22권1_2호
• /
• pp.373-385
• /
• 2006

To solve a class of nonlinear parameter estimation problems, a method combining the regularized structured nonlinear total least norm (RSNTLN) method and parameter separation scheme is suggested. The method guarantees the convergence of parameters and has an advantages in reducing the residual norm over the use of RSNTLN only. Numerical experiments for two models appeared in signal processing show that the suggested method is more effective in obtaining solution and parameter with minimum residual norm.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.270-276
• /
• 2000

Hard turning has the potential to replace grinding process and to achieve significant reduction in production time and cost. The main applications for hard turning is finishing process, namely grinding process. Therefore, it must be able to satisfy high surface integrity of the workpiece. This paper discusses surface quality in terms of residual stress and damaged layer with respect to cutting parameters in an intermittent hard turning. Damaged layer experiment is carried out orthogonal array. From that is based on the orthogonal array. From the response table, cutting parameters are analyzed from the view point of the damaged layer and residual stress. From this experimental results, even though in the intermittent hard turning, surface integrity turns out be good enough for replacing grinding process.

• Steel and Composite Structures
• /
• 제7권5호
• /
• pp.391-404
• /
• 2007

This paper presents push-out tests of stud shear connectors to examine their fatigue behavior for developing a new composite bridge deck system. The fifteen push-out specimens of D16 mm stud welded on 9 mm steel plate were fabricated according to Eurocode-4, and a series of fatigue endurance test and residual strength test were performed. Additionally, the stiffness and strength variations by cyclic loading were compared. The push-out test, when the stiffness reduction ratio of the specimens was 0.95 under cyclic load, resulted in the failure of the studs. The stiffness variation of the push-out specimens additionally showed that the application of cyclic loads reduced the residual strength. The fatigue strength of the shear connectors were compared with the design values specified in the Eurocode-4, ASSHTO LRFD and JSSC codes. The comparison result showed that the fatigue endurance of the specimens satisfies the design values of these codes.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권9호
• /
• pp.495-501
• /
• 2000

This paper presents a method to minimize the initial deflection of a multi-layer piezoelectric microactuator without loosing its piezoelectric deflection performance required for light modulating micromirror devices. The multi-layer piezoelectric actuator composed of PZT silicon nitride and platinum layers deflects or buckles due to the gradient of residual stress. Based on the structural analysis results and relationship between process conditions and mechanical properties we have modified the fabrication process and the thickness of thin film layers to reduce the initial residual stress deflection without decreasing its piezoelectric deflection performance. The modified designs fabricated by surface-micromachining process achieved the 77% reduction of the initial deflection compared with that of the conventional method based on the measured micromechanical material properties is applicable to the design refinement of multi-layer MEMS devices and micromechanical structures.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.578-585
• /
• 2004

Hardness test is performed for determination of the other properties, such as strength, wear resistance and deformation resistance, as well as hardness itself. And it is performed for prediction of residual lifetime by analysis of hardness reduction or hardness ratio. However, hardness test has limitation that observation of residual indent is needed for determination of hardness value, and that is the reason for not to be widely used in industrial field. Therefore, in this study, we performed researches to obtain Brinell hardness value from quantitative numerical formula by analysing relationship between indentation depths from indentation load-depth curve and mechanical properties such as work hardening exponent, yield strength and elastic modulus.

• 한국소음진동공학회논문집
• /
• 제18권1호
• /
• pp.3-10
• /
• 2008

In this paper, the optimal command input is considered in order to minimize the residual vibrations of a flexible cantilever beam when the beam simply changes its position by translation or rotation. Although a cantilever beam has many modes of vibration, it is shown that the consideration of the first mode is sufficient in this case. Thus, the problem becomes a single-degree-of-freedom system subjected to a ground excitation. Two simple methods are proposed to find the optimal command input based on the shock response spectrum (SRS). The first method is the simplest and can be applied to lightly damped cases, and the second method is applicable to more general problems. The second method gives almost the same results as the input shaping method. However the proposed method gives a easier and clearer control strategy.

• 한국표면공학회지
• /
• 제37권5호
• /
• pp.273-278
• /
• 2004

The requirements of getting spring steel with higher fatigue strength have been increased to achieve the weight reduction of a vehicle. As the possible increment in fatigue strength by using the conventional shot peening treatment is found to be limited, it is necessary to modify the shot peening treatment. In this study, to investigate the effects of warm shot peening on increasing fatigue strength, tests are conducted on spring steel SAE9524. By the results of rotating bending fatigue tests, the fatigue strength increases up to 23.8% in warm shot peening specimens at $200^{\circ}C$ compared with conventional shot peening. The major reason why the warm shot peening is effective to the improvement of fatigue strength is the increment of the compressive residual stress, which can be effectively formed by shot peening under the condition of warm temperature than room temperature.

• Structural Engineering and Mechanics
• /
• 제69권1호
• /
• pp.105-120
• /
• 2019

In this paper, a new efficient method for structural modal reanalysis is proposed, which can handle large finite element (FE) models requiring frequent design modifications. The global FE model is divided into a residual part not to be modified and a target part to be modified. Then, an automated matrix permutation and substructuring algorithm is applied to these parts independently. The reduced model for the residual part is calculated and saved in the initial analysis, and the target part is reduced repeatedly, whenever design modifications occur. Then, the reduced model for the target part is assembled with that of the residual part already saved; thus, the final reduced model corresponding to the new design is obtained easily and rapidly. Here, the formulation of the proposed method is derived in detail, and its computational efficiency and reanalysis ability are demonstrated through several engineering problems, including a topological modification.

• 한국정보전자통신기술학회논문지
• /
• 제6권1호
• /
• pp.23-28
• /
• 2013

본 논문에서는 모바일 환경에서 dual microphone을 이용하여 배경 잡음을 효율적으로 제거하는 방법을 제안한다. 참조 마이크와 주 입력 마이크로부터 측정된 신호를 각각 FDAF의 참조신호와 주 입력 신호로 하여 잡음 제거를 수행한 뒤에 MMSE-LSA를 이용하여 잔여 잡음 및 배경 잡음을 추정하여 제거 한다. 이때 일관성 있는 잡음 제거 성능을 위해 두 마이크 신호의 PLD를 이용한 VAD 결과를 사용한다.

• 한국표면공학회지
• /
• 제21권1호
• /
• pp.19-27
• /
• 1988

The principe and practice of pulse plating, and prospect in the future on pulse plating are reviewed. Some of the advantages of pulse pulse plating are detailed as compared with DC plating. The advantages of pulse plating are summarized as follows: 1)smooth and fine grained deposits 2) reduction in hydrogen embrittlement of deposits 3) reduction of residual stress and microcracks in the deposit 4) improvement of physical properties 5) uniform alloy composition through the deposit thinkness 6) improved thrower and adhesion.