• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1685-1691
• /
• 2004

This paper describes the fault detection and failsafe logic to be used in an Electronic Stability Program(ESP). The aim of this paper is to prevent of erroneous controls in the ESP. Developed this paper introduces the fault detection logic and evaluation of residual signals. The failsafe logic consists of four redundant sub-models, which can be used for detecting the faults in various sensors (yaw rate, lateral acceleration, steering wheel angle). We present two mathematical residual generation methods : one is a method using the average value and the other is a method using the minimum value of the each residual. We verified a failsafe logic developed using vehicle test results also we compare vehicle model based simulation results with test vehicle results.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.774-779
• /
• 2004

This paper describes the fault detection and failsafe logic to be used in the Electronic Stability Program (ESP). The Aim of this paper is prevention of erroneous control in the ESP. This paper introduces the fault detection logic and evaluation of residual signals. Failsafe logic consist of four redundant sub-models and they can be used for the detection of faults in each sensor (yaw rate, lateral acceleration, steering wheel angle). We presents two mathematical residual generation method ; one is the method by the average value, and the other is the method by the minimum value of the each residual. We verify a failsafe logic using vehicle test results, also we compare vehicle model based simulation results with test vehicle results.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.93-98
• /
• 2013

Nanoimprint lithography (NIL) is a next generation technology for fabrication of micrometer and nanometer scale patterns. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. To successfully imprint a nanosized pattern with the thermal NIL, the process conditions such as temperature and pressure should be appropriately selected. This starts with a clear understanding of polymer material behavior during the thermal NIL process. In this paper, a filling process of the polymer resist into nanometer scale cavities during the thermal NIL at the temperature range, where the polymer resist shows the viscoelastic behaviors with consideration of stress relaxation effect of the polymer. In the simulation, the filling process and the residual layer formation are numerically investigated. And the effects of pressure and temperature on NIL process, specially the residual layer formation are discussed.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.4
• /
• pp.68-74
• /
• 2017

Nanoimprint lithography (NIL) is a next generation technology for fabrication of micrometer and nanometer scale patterns. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. Up to now there have been a lot of researches on thermal NIL, but most of them have been focused on polymer deformation in the molding process and there are very few studies on the cooling and demolding process. In this paper a cooling process of the polymer resist in thermal NIL is analyzed with finite element method. The modeling of cooling process for mold, polymer resist and substrate is developed. And the cooling process is numerically investigated with the effects of imprinting temperature and residual layer thickness of polymer resist on stress distribution of the polymer resist. The results show that the lower imprinting temperature, the higher the maximum von Mises stress and that the thicker the residual layer, the greater maximum von Mises stress.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2227-2229
• /
• 2004

Fault Detection and Isolation(FDI) schemes using unknown input functional observers with very low order are presented. These schemes resolve the major practical difficulties with all FDI systems employing multiple observers for residual generation and can be implemented by the use of microprocessors that are normally used in commercial processes mainly due to the simplicity of the residual generation block. Various design objectives including detection, isolation, estimation and compensation of instrument fault/or process fault are achievable with these schemes. The proposed FDI scheme is applied to an inverted pendulum control system for instrument fault detection.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.98-103
• /
• 2008

This paper is to discuss distribution of welding residual stresses of a ferritic low alloy steel nozzle with dissimilar metal weld using Alloy 82/182. Two dimensional (2D) thermo-mechanical finite element analyses are carried out to simulate multi-pass welding process on the basis of the detailed and fabrication data. On performing the welding analysis generally, the characteristics on the heat input and heat transfer of weld are affected on the weld residual stress analyses. Thermal analyses in the welding heat cycle process is very important process in weld residual stress analyses. Therefore, heat is rapidly input to the weld pass material, using internal volumetric heat generation, at a rate which raises the peak weld metal temperature to $2200^{\circ}C$ and the base metal adjacent to the weld to about $1400^{\circ}C$. These are approximately the temperature that the weld metal and surrounding base materials reach during welding. Also, According to the various ways of appling the weld heat source, the predicted residual stress results are compared with measured axial, hoop and radial through-wall profiles in the heat affected zone of test component. Also, those results are compared with those of full 3-dimensional simulation.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.43-52
• /
• 1999

In this study, theoretical stress field analysis near the crack tip under tension-compression loading was performed. The results of the theoretical stress analysis were compared to the results of Finite Element Method(FEM). From this study, generation of tensile residual stress at crack tip was proved after 1-cycle of tension-compression loading, and the fracture toughness and the fracture load of a structure can be decreased by the residual stress.

• Journal of Communications and Networks
• /
• v.15 no.3
• /
• pp.258-265
• /
• 2013

In this study, we investigate the multi-carrier spread spectrum (MCSS) communication system which adopts the self-encoded spread spectrum in a downlink synchronous channel. It is very difficult to completely eliminate the frequency offset in practical channel scenarios. We demonstrate that the self-encoded MCSS (SE-MCSS) with iterative despreading manifests a remarkable immunity to residual frequency offset. The SE-MCSS can be an excellent candidate for the future generation of wireless services.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2014-2016
• /
• 2003

A new residual generation scheme that can be employed in the process fault detection and isolation systems for linear (control) systems is suggested. The scheme is very simple, but provides the same information for the detection and isolation of the anticipated faults as the conventional multiple observer based schemes. Application results show the practical feasibility of the proposed scheme.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.3
• /
• pp.331-337
• /
• 2009

Electrolysis produces hypochlorous acid by using a small quantity of NaCl as electrolyte. This process maximizes the stabilization of drinking water through the control of chlorine residual concentration. This study investigated free chlorine generation by an electrolytic method using $Ti/IrO_2$ and stainless steel. The generation of free chlorine was increased with increasing hydraulic retention time, voltage, chlorine ion concentration and the number of electrodes. However, the change of pH did not affect the generation of free chlorine. There was no significant difference on the behavior of chlorine concentration between electrolytic method and NaOCl injection. In this study, the concentration of free chlorine predicted model based on power functional model was developed various under conditions. Electrolysis free chlorine generation model can be effective tool in the estimation of free chlorine generation.