• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.5
• /
• pp.79-84
• /
• 2012

As the huge economical loss and function paralysis of information technology-based systems can be caused by the misoperation of residual current devices(RCDs) due to surge voltages and currents, RCDs shall not operate by surge currents. In this paper, in order to evaluate the reliability of residual current operated circuit-breakers with integral overcurrent protection for household and similar uses((RCBOs) stressed by surges, the unintended trip characteristics of RCBOs under surge currents were experimentally investigated using the combination wave generator. Seven different types of single-phase RCBOs being present on the domestic market were investigated according to KS C IEC 61009-1 standard. As a result, all kinds of specimens were satisfied the requirements for 0.5 [${\mu}s$]/100[kHz] ring wave impulse currents. Most of specimens stressed by the 8/20[${\mu}s$] impulse current tripped at least one or more, and some of them were broken down during consecutive tests. It was found that only one type of specimens meets the L-N mode immunity to the combination wave of 1.2/50[${\mu}s$] impulse voltage and 8/20[${\mu}s$] impulse current.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.7-13
• /
• 2001

Wire electrical discharge machining experiments in conducted to investigate characteristics of acoustic emission (AE) and electrical discharge energy due to current peak (I$_{p}$), pulse on time($\tau$/on/). The AE signals are obtained with a sensor attached to workpiece side. Machining states are identified with scanning electron microscopy and residual stress analyzer. It is demonstrated that the residual stress provide reliable informations about the machining states. Moreover, machining states can be detected successfully using both the residual stress and AE count rate.e.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.441-450
• /
• 2000

In order to improve the water quality in semi-enclosed bays, Gug et al. (1997) have proposed a new method to activate the tidal exchange by creation and control of tidal residual current through the addition of artificial elements to creation and control of tidal residual current through the addition of artificial elements to create bottom roughness, so, ot is advisable to arrange as few of these as possible from a point of cost-benefit view. This paper attempts to develop the most suitable shape of artificial bottom roughness units with which to create and control an optimal tidal residual current. Several simple shapes were examined as fundamental cases. Subsequently 38 types of artificial bottom roughness units based on a few simple effective shapes, were examined experimentally. As a result of this research, two types to create artificial roughness.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.791-793
• /
• 1993

The hall sensor is current detector using hall effect in semiconductor and the conventional type detect current with concentrating flux by current of conductor. So, detection of small current is very difficult because of residual magnetism. This paper give the experiments based results about method that detect the small DC current using minimizing the residual of hall element by magnetic modulation and concentrating flux. The suggested sensor can dector small current better than the conventional that.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.2
• /
• pp.198-207
• /
• 2008

The conventional Residual Current Protective Devices(RCD, or earth leakage circuit breaker, ELB) operates depending on the total leakage current which is the vector-sum of resistive and capacitive components of a leakage current. However, the electric disaster such as electric shock or fire is mainly caused by the resistive component. Therefore, in this view point, the RCD is more realistic when it operates by the resistive component of the leakage current. In this paper, a new algorithm for measuring the resistive leakage current from the total leakage current is suggested, and is realized to an actual circuit. According to the suggested algorithm, the resistive component of the leakage current can be found by integrating the total leakage current over only a half cycle of the line voltage, and it is realized by using analog switches and resettable integrators. It is confirmed through experiments that the suggested algorithm detects, within maximum average error of 6.74%, the resistive leakage current from the total leakage current, and the RCD employing the suggested algorithm brakes the circuit within the regular interrupt time(30msec).

• 한국해양학회지
• /
• v.22 no.1
• /
• pp.9-18
• /
• 1987

A number of hydrographic studies and some recent current measurements around Chejudo Island suggest an existence of a clockwise residual flow in the west and north coasts of the island all the year round. On the eastern side of the island the Tsushinma Current flows northward and northeastward. The contribution of tide-induced residual currents to the observed residual. flow around the island was examined here through numerical solution of the two-dimensional nonlinear shallow-water equations. The calculated tide-induced residual currents show a clockwise circulation around the island. Significant residuals of 2-4cms$\^$-1/are confined over sloping bottom topography around t he island and the far-field residuals are negligibly small. The inclusion of a permanent current into the model was also attempted in order to see the effects of the Tsushima Current system on the residual circulation around the is land. It was found that combined effects of tide-induced residuals and the permanent current field associatedwith the Tsushima Current explain qualitatively not only the observed clock wise residuals in the west and north coasts but also the northward flow on the eastern side of the island.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.3
• /
• pp.149-158
• /
• 2012

This study analyzed cross-sectional variations in residual current and strengths of stratification by observing cross-sectional velocity and salinity during spring tide and neap tide, respectively, for continuous 13-hour periods at 2 observation lines at northern and southern end of Seokmo Channel, which is located west of Ganghwado. Salinity distribution of channel depends on not only neap and spring tide but also impact of salinity. The residual current component was obtained by removing $M_2$ and $M_4$ tidal components that were extracted using the least squares method on 13-hour velocity component. Cross-section of residual velocity at northern and southern end of Seokmo Channel exhibited southward residual components at channel's surface layer, but northward residual current was observed at channel's bottom layer, clearly showing a 2-layer tidal circulation between surface and bottom layers. The variation in location of appearing northward residual current according to changes in spring and neap tidal cycle and its correlation with stratification were analyzed using the Richardson number and Simpsonhunter index. At northern and southern end of Seokmo Channel, northward residual current appears in the location where Richardson number is large, Simpson-hunter index appears as a value greater than 4.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.101-108
• /
• 1999

A reliable and practical monitoring of drill breakage is a crucial technique in automatic machining system. In this study, a real-time monitoring system was developed to predict drill breakage using both spindle and z-axis motor current. Drill breakage is monitored by detecting the level of residual motor current which is obtained through the moving average filter algorithm. The residual exhibits a feature of sharp decrease just before drill breakage. Therefore, drill breakage can be predicted by detecting this characteristic of residual component. Z-axis motor current is better to predict the drill breakage than spindle motor current, because the former is faster in response than the latter when drill breakage is occurred. The evaluation experiments have shown that the developed monitoring system works very well.

• Journal of Environmental Science International
• /
• v.11 no.1
• /
• pp.25-32
• /
• 2002

In order to control of water quality in Jeju harbor, variation of physical oceanographic environments was estimated using material cycle model. It is composed of the three-dimensional hydrodynamic model for the simulation at water flow and material cycle model for the simulation of water quality. The three dimensional hydrodynamic model simulation of the circulation and mixing in Jeju Harbor has been conducted forced by Sanzi River Discharge, Tidal elevation, wind and Solar heat in case of August and November, 2000 and February and May, 2001, respectively. The results of numerical model and observation show that the model can produce realistic results of current in the harbor. The monthly variation of velocity pattern are not so much changed are found In Jeju Harbor. The residual current was forced by temperature, salinity, density, wind and tidal current. The residual current of August, 2000 are the strongest among four month. It can be explained that the density effect can be important role in residual current at Jeju Harbor. As the results of salinity distribution simulation, very low concentration of all levels were simulated in August, 2000. The flowrate of Sanzi river was investigated 77,760 ㎥ /d in August, 2000. Therefore, pollutant loadings from Sanzi river should be considered for water quality management in Jeiu harbor.

• Journal of Korean Port Research
• /
• v.12 no.1
• /
• pp.95-104
• /
• 1998

Water pollution in a semi-enclosed sea area such as a bay due to stagnancy of water has been a serious water environmental problem. Recently, some kinds of new methods to activate the tidal exchange between an inner bay and an outer sea area by control of a tidal residual current have been proposed. However, these methods have several problems, that is, I). deterioration in a natural view due to building of huge structures, II). increase of risk of navigation in case of a submerged structure, III). limition of sea area where a tidal current can be controlled and IV). difficulty in removing those structures in case of occurrence of an unexpected impact on water environment. In this paper, a new method is proposed, which can solve all the above problems, to purify water quality in a semi-enclosed bay by creation and control of a pattern of a tidal residual current. The tidal residual current is controlled by unsymmetric structures, which change the properties of resistance according to the direction of flow, arranged on the sea bottom. In this study, several numerical and hydraulic experiments of tidal current and particle-tracking for various arrangements of bottom roughness in a semi-enclosed model bay were carried out. As a result of experiments, it becomes clear that it is possible to generate a new tidal residual current and to activate a tidal exchange by only operation of bottom roughness arrangement.