• 한국가금학회지
• /
• 제42권3호
• /
• pp.257-265
• /
• 2015

생후 초기에 고온을 경험하게 되면 이후 고온환경에 대하여 저항성을 획득하는 것으로 알려져 있다. 본 연구에서는 5일령의 병아리에게 단시간 고온을 경험하게 한 다음, 29일령에 1차 고온환경을 경험한 육계에서 반복된 고온환경이 생산성에 미치는 영향을 조사하였다. 아버에이커 초생추를 크기가 동일한 두 개의 사육실에 수용하였으며, 사료와 물은 자유채식토록 하였다. 조명 환경 조건은 점등 23시간, 소등 1시간이었다. 사전 고온 적응구는 5일령에 $37^{\circ}C$의 고온에 24시간 동안 노출시킨 후 정상 온도로 돌려졌고, 대조구의 감온 일정은 정상적으로 진행되었다. 21일령에 육계를 기존에 수용된 사육실에서 반을 다른 사육실로 옮겨, 한 사육실 내 대조군와 열 적응구가 각각 4개의 Pen에 배치되게 하였다. 1) 사전고온 적응 및 고온환경 양자 모두를 경험하지 않은 육계집단(CON+CON), 2) 사전고온 적응을 경험했지만 고온환경을 경험하지 않은 육계집단(HC+CON), 3) 사전고온 적응 없이 고온환경만 경험한 육계집단(CON+HS), 4) 사전고온 적응 및 고온환경 모두를 경험한 육계집단(HC+HS) 을 가지는 이원배치법(HC vs. HS) 으로 실험을 수행하였다. 29일령부터 3일 동안 고온환경에 노출된 육계들은 43일령부터 재차 고온환경을 경험하였다. 고온환경 처리구에서 사육실 온도를 $32^{\circ}C$($2^{\circ}C$/1 h)까지 올려 3일 동안 유지하였으며, 대조구는 $22^{\circ}C$로 유지되었다. 고온환경은 사료 섭취량, 음수량 및 체중을 현저하게 감소시켰으며, 직장 온도와 폐사율 및 corticosterone의 농도를 증가시켰고, 혈액 생화학 성분을 변화시켰다. 그러나 사전열적응한 육계에서는 비장의 상대무게가 유의적으로 높았다. 따라서 연구결과를 종합적으로 고려해볼 때, 사전고온 적응은 반복적으로 고온환경을 경험하는 육계에게 고온에 대한 저항성을 부여하지 않았다는 것을 의미한다.

• 대한의용생체공학회:의공학회지
• /
• 제35권5호
• /
• pp.125-131
• /
• 2014

The purpose of this study is to verify the utility of reflected photoplethysmography sensor using two green light emitting diodes that influenced by ambient light. Recently it has been studied that green light emitting diode is suitable for light source of reflected photoplethysmography sensor at low temperature and high temperature. Another study showed that, green light is better for monitoring heart rate during motion than led light. However, it has a bad characteristic about ambient light noise. To verify the utility of reflected photoplethysmography sensor using green light emitting diode, this study measures the photoplethysmography signal that is distorted by ambient light and will propose a solution. This study has two parts of research method. One is measurement system that composed sensor and board. The sensor is made up PE-foam and Non-woven fabric for flexible sensor. The photoplethysmography signal is measured by measurement board that composed high-pass filter, low-pass filter and amplifier. Ambient light source is light bulb and white light emitting diode that has three steps brightness. Photoplethysmography signal is measured with lead II electrocardiography signal at the same time and it is measured at the finger and radial artery for 1 minute, 1000 Hz sampling rate. The lead II electrocardiography signal is a standard signal for heart rate and photoplethysmography signal that measured at the finger is a standard signal for waveform. The test is repeated 3 times using three sensor. The data is processed by MATLAB to verify the utility by comparing the correlation coefficient score and heart rate. The photoplethysmography sensor using two green light emitting diodes is shown better utility than using one green light emitting diode and red light emitting diode at the ambient light. The waveform and heart rate that measured by two green light emitting diodes are more identical than others. The amount of electricity used is less than red light emitting diode and error peak detectability factor is the lowest.

• 한국안전학회지
• /
• 제38권3호
• /
• pp.35-42
• /
• 2023

This study analyzed the current and temperature characteristics of major components of an induction motor during normal and abnormal operations as functions of the difference in the rated capacities of medium and large-sized motors widely used in industrial settings. The temperature rise equation of the induction motor winding was derived through locked-rotor operation experiments and linear regression analysis. When the ambient temperature is 40 ℃, the time to reach 155 ℃, the temperature limit of the insulation class (F class) of the winding of the induction motor, was confirmed to be 48 seconds for the 2.2 kW induction motor and 39 seconds for the 3.7 kW induction motor. This means that when the rated capacity is large or the installation environment is high temperature, the time to reach the temperature limit of the insulation class during locked-rotor operation is short, and the risk of insulation deterioration and fire is high. In addition, even if the EOCR (Electronic Over Current Relay) is installed, if the setting time is excessively set, the EOCR does not operate even if the normal and locked-rotor operation of the induction motor is repeated, and the temperature limit of the insulation grade of the winding of the induction motor is exceeded. The results of this study can be used for preventive measures such as the promotion of electrical and mechanical measures for the failure of induction motors and fire prevention in industrial sites, or the installation of fire alarm systems.

• 한국재료학회지
• /
• 제16권9호
• /
• pp.592-597
• /
• 2006

A deoxidized low-phosphorous (DLP) copper was processed by accumulative roll-bonding (ARB) for ultra grain refinement and high strengthening. Two copper sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked to each other, and roll-bonded by about 50% reduction rolling without lubrication at ambient temperature. The bonded sheet is then cut to the two pieces of same dimensions and the same procedure was repeated to the sheets up to eight cycles (${\varepsilon}{\sim}6.3$). TEM observation revealed that ultrafine grains were developed after the 4th cycle, and their size decreased at higher cycles. Tensile strength of the copper increased with the equivalent strain, and it reached 547 MPa which was 3 times higher than that of the initial material. It is concluded that the ARB process is an effective method for high strengthening of the DLP copper.

• 한국재료학회지
• /
• 제19권8호
• /
• pp.432-436
• /
• 2009

A Cu-Fe-P copper alloy was processed by accumulative roll-bonding (ARB) for ultra grain refinement and high strengthening. Two 1mm thick copper sheets, 30 mm wide and 300 mm long, were first degreased and wire-brushed for sound bonding. The sheets were then stacked on top of each other and roll-bonded by about 50% reduction rolling without lubrication at ambient temperature. The bonded sheet was then cut into two pieces of the same dimensions and the same procedure was repeated for the sheets up to eight cycles. Microstructural evolution of the copper alloy with the number of the ARB cycles was investigated by optical microscopy (OM), transmission electron microscopy(TEM), and electron back scatter diffraction(EBSD). The grain size decreased gradually with the number of ARB cycles, and was reduced to 290 nm after eight cycles. The boundaries above 60% of ultrafine grains formed exhibited high angle boundaries above 15 degrees. In addition, the average misorientation angle of ultrafine grains was 30 degrees.

• 한국재료학회지
• /
• 제21권12호
• /
• pp.655-659
• /
• 2011

An ultrafine grained complex aluminum alloy was fabricated by an accumulative roll-bonding (ARB) process using dissimilar aluminum alloys of AA1050 and AA5052 and subsequently annealed. A two-layer stack ARB process was performed up to six cycles without lubricant at an ambient temperature. In the ARB process, the dissimilar aluminum alloys, AA1050 and AA5052, with the same dimensions were stacked on each other after surface treatment, rolled to the thickness reduction of 50%, and then cut in half length by a shearing machine. The same procedure was repeated up to six cycles. A sound complex aluminum alloy sheet was fabricated by the ARB process, and then subsequently annealed for 0.5h at various temperatures ranging from 100 to $350^{\circ}C$. The tensile strength decreased largely with an increasing annealing temperature, especially at temperatures of 150 to $250^{\circ}C$. However, above $250^{\circ}C$ it hardly decreased even when the annealing temperature was increased. On the other hand, the total elongation increased greatly above $250^{\circ}C$. The hardness exhibited inhomogeneous distribution in the thickness direction of the specimens annealed at relatively low temperatures, however it had a homogeneous distribution in specimens annealed at high temperatures.

• 한국재료학회지
• /
• 제24권11호
• /
• pp.585-590
• /
• 2014

Microstructural evolution in the thickness direction of an oxygen free copper processed by accumulative rollbonding (ARB) is investigated by electron back scatter diffraction (EBSD) measurement. For the ARB, two copper alloy sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked and roll-bonded by about 50% reduction rolling without lubrication at an ambient temperature. The bonded sheet is then cut to the two pieces of the same dimensions and the same procedure was repeated on the sheets up to eight cycles. The specimen after 1 cycle showed inhomogeneous microstructure in the thickness direction so that the grains near the surface were finer than those near the center. This inhomogeneity decreased with an increasing number of ARB cycles, and the grain sizes of the specimens after 3 cycles were almost identical. In addition, the aspect ratio of the grains decreased with an increasing number of ARB cycles due to the subdivision of the grains by shear deformation. The fraction of grains with high angle grain boundaries also increased with continuing process of the ARB so that it was higher than that of the low angle grain boundaries in specimens after 3 cycles. A discontinuous dynamic recrystallization occurred partially in specimens after 5 cycles.

• 분석과학
• /
• 제14권3호
• /
• pp.274-285
• /
• 2001

본 연구는 ppb와 ppt 정도의 농도 수준으로 존재하고 있는 대기 중 휘발성 유기화합물을 분석하기 위해 열탈착-저온농축-GC/FID/FPD를 개발하였다. 그리고 고체흡착제가 충진된 흡착관과 자체 제작한 휴대용 가스채취기를 사용하여 강원도 춘천지역에 위치한 근화동과 혈동리 생활폐기물 매립장에서 배출되는 VOCs를 채취하였다. 저온농축방법으로는 분석컬럼을 직접 저온 농축하는 on-column 저온 농축장치와 0.8mm loop를 이용한 저온농축장치를 서로 비교 검토해 보았다. On-column 저온농축법은 loop에 비해 분리능은 좋으나 흡착관에 채취한 시료를 저온농축할 때 요구되는 50 psi의 높은 탈착압력으로 인해 흡착관의 SwageLok fitting이 마모되어 가스가 새는 문제점이 발생하였다. 이에 반해 탈착압력을 낮추고 탈착유량을 늘리기 위해 설계한 loop 경우에는 탈착압력이 0.4 psi로 on-column에 비해 매우 낮아 가스가 새는 것을 방지할 수 있었다. 열탈착-저온농축-GC/FID/FPD로 분석한 근화동과 혈동리 생활폐기물 매립장에서 검출된 물질로는 toluene, xylene, ethylbenzene등 탄화수소류와 악취물인 styrene, limonene, dimethyl disulfide 등이 검출되었다. 그리고 매립지에서 방출되는 VOCs는 매립되는 폐기물의 조성과 매립기간에 따라 다르게 나타났다. 검출된 화합물은 저온농축-GC/MS를 이용하여 확인하였다.