• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.317-326
• /
• 2017

Comparative fishing experiments were conducted in the eastern coastal waters near Uljin, Korea from 2002 to 2004, using the experimental trammel nets to estimate the selectivity for spinyhead sculpin Dasycottus setiger. The inner panels of the nets were made of nylon monofilament with four mesh sizes (82.2, 89.4, 104.8, and 120.2 mm) while its two outer panels were made of twisted nylon multifilament with a mesh size of 510 mm. The SELECT (Share Each Length's Catch Total) procedure with maximum likelihood method was applied to obtain a master selection curve. The different functional models (normal, lognormal, bi-normal, and logistic model) were fitted to the catch data. The lognormal model with the fixed relative fishing intensity was chosen as the best-fitted selection curve through comparison of model deviance and AIC (Akaike's Information Criterion). The optimum relative length (the ratio of fish total length to mesh size) with the maximum relative efficiency was obtained as 2.492.

• Geomechanics and Engineering
• /
• v.11 no.5
• /
• pp.639-655
• /
• 2016

The effect of particle breakage and intermediate principal stress ratio on the behaviour of crushable granular assemblies under true triaxial stress conditions is studied using the discrete element method. Numerical results show that the increase of intermediate principal stress ratio $b(b=({\sigma}_2-{\sigma}_3)/({\sigma}_1-{\sigma}_3))$ results in the increase of dilatancy at low confining pressures but the decrease of dilatancy at high confining pressures, which stems from the distinct increasing compaction caused by breakage with b. The influence of b on the evolution of the peak apparent friction angle is also weakened by particle breakage. For low relative breakage, the relationship between the peak apparent friction angle and b is close to the Lade-Duncan failure model, whereas it conforms to the Matsuoka-Nakai failure model for high relative breakage. In addition, the increasing tendency of relative breakage, calculated based on a fractal particle size distribution with the fractal dimension being 2.5, declines with the increasing confining pressure and axial strain, which implies the existence of an ultimate graduation. Finally, the relationship between particle breakage and plastic work is found to conform to a unique hyperbolic correlation regardless of the test conditions.

• Journal of Korean Institute of Industrial Engineers
• /
• v.15 no.2
• /
• pp.33-44
• /
• 1989

This paper presents stochastic-statistical dominance rules which eliminate dominated alternatives thereby reduce the number of satisficing alternatives to a manageable size so that the decision maker can choose the best alternative among them when neither the utility function nor the probability distribution of outcomes is exactly known. Specifically, it is assumed that only the characteristics of the utility function and the value function are known. Also, it is assumed that prior probabilities of the mutually exclusive states of nature are not known, but their relative bounds are known. First, the notion of relative risk aversion is used to describe the decision maker's attitude toward risk, which is defined with the acknowledgement that the utility function of the decision maker is a composite function of a cardinal value function and a utility function with-respect to the value function. Then, stochastic-statistical dominance rules are developed to screen out dominated alternatives according to the decision maker's attitude toward risk represented in the form of the measure of relative risk aversion.

• Environmental and Resource Economics Review
• /
• v.10 no.3
• /
• pp.323-344
• /
• 2001

This study analyzes the relative efficiencies of three types of non-landfill treatment of food wastes; recycling to fertilizers or animal feeds, reducing the size of food wastes, and fermentation of food wastes. Unlike previous studies our study incorporates not only usual inputs and outputs but also emissions of pollutants such as odor and noise generated by the treatment facilities into the analysis. A nonparametric method suggested by Fare et al. (1989) has been used to estimate the relative efficiencies of facilities incorporating emission of pollutants. The results show that recycling is more efficient than the other two treatment methods. It is also shown that the usual models that do not incorporate the environmental aspects of the treatment facilities derive a biased conclusion on the relative efficiencies.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.476-479
• /
• 2005

In this study, the process parameters in powder compaction are optimized for getting high relative densities. To find optimized parameters, the analytic models of powder compaction are firstly prepared by 2-dimensional rod arrays with random green densities using a quasi-random multi-particle array. Then, using finite element method, the changes in relative densities are analyzed by varying the size of the particle, the amplitude of cyclic compaction, and the coefficient of friction, which influence the relative density in cyclic compactions. After the analytic function of relative density associated process parameters are formulated by aid of the response surface method, the optimal conditions in powder compaction process are found by the grid search method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.1
• /
• pp.54-60
• /
• 2012

When the transient current with high frequency components such as lightning surges are injected the grounding electrodes, the performance of grounding electrodes should be evaluated as grounding impedance. It is restricted to analyze the grounding impedance by measurement approach since the grounding impedance is very different with the shape and size of grounding electrodes, resistivity and relative permittivity of soil and the frequency component of the injected current. So a variety of simulation approaches have been developed. Typically, the soil resistivity measured with low frequency and relative permittivity between 1 and 80 are used for simulation of the grounding impedance. However, the resistivity and relative permittivity of soil are changed with frequency of injected current. In this paper, the frequency-dependent resistivity and relative permittivity of soil are measured and these parameters are reflected in the simulation of the grounding impedance of a ground rod. The simulated results are compared with the measured results. As a result, the simulated results with frequency-dependent soil parameters show capacitive aspect like measured results in the frequency of lower than 100[kHz] and they are more consistent with the measured results in wide frequency range.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1699-1702
• /
• 2012

$TiO_2$ nanostructures with various morphologies like cubes, spheres, hexahedral pillars and spherical tubes were synthesized by microwave-assisted hydrothermal process. Each structure was obtained by changing the relative concentrations of titanium tetraisoproxide (TTIP), tetrabutylammonium hydroxide (TBAH) and ethanol. Scanning electron microscopy (SEM), transmission electoron microscopy (TEM), X-ray diffraction and Brunauer-Emmett-Teller (BET) surface area analysis were used to characterize the synthesized $TiO_2$ nanostructures. From these results, it has been proved that $TiO_2$ structure could be controlled to have specific morphology, size, surface area, pore volume and pore size distribution.

• Korean Journal of Computational Design and Engineering
• /
• v.1 no.3
• /
• pp.215-223
• /
• 1996

Every mechanical part is fabricated with the variations in its size and shape, and the allowable range of the variation is specified by the tolerance in the design stage. Geometric tolerances specify the size or the thickness of each shape entity itself or its relative position and orientation with respect to datums while considering their order of precedence. It would be desirable if the assemblability of parts could be verified in the computer when the tolerances on the parts are store together with the geometric model of the parts of an assembly and their assembled state. Therefore, a new method is proposed to represent geometric tolerances and to determine the assemblability. This method determines the assemblability by subdividing the ranges of relative motion between parts until there exists the subdivided regions that do not cause the interference.

• Steel and Composite Structures
• /
• v.26 no.2
• /
• pp.241-253
• /
• 2018

Mode II fracture toughness, $K_{IIC}$, of single-ply triaxially woven fabric (TWF) composite due to tow waviness and anisotropy effects were numerically and experimentally studied. The numerical wavy beam network model with anisotropic material description denoted as TWF anisotropic was first validated with experimental Mode II fracture toughness test employing the modified compact tensile shear specimen configuration. 2D planar Kagome and TWF isotropic models were additionally constructed for various relative densities, crack lengths, and cell size parameters for examining effects due to tow waviness and anisotropy. $K_{IIC}$ generally increased with relative density, the inverse of cell size, and crack length. It was found that both the waviness and anisotropy of tow inflict a drop in $K_{IIC}$ of TWF. These effects were more adverse due to the waviness of tow compared to anisotropy.

• Journal of Korean Society for Quality Management
• /
• v.17 no.2
• /
• pp.121-141
• /
• 1989

This paper is concerned with a development and evaluation of heuristics for the multi-stage sequence dependent flowshop sequencing. Eighteen heuristics, CAM1, CAM2, and etc., are proposed. The performance measure is a makespan which is to be minimized. The experiment for each algorithm is designed for a 4*3*3 factorial design with 360 observations. The experimental factors are PS(ratio of processing times to setup times), M(number of machines), N(number of jobs). The makespan of the proposed heuristics is compared with the optimal makespan obtained by the complete enumeration of schedules. This yardstick of comparison is called a relative error. The mean relative errors of the eighteen heuristics are from 2.048% to 8.717%. The computational results are analysed using SPSS. The experimental results show that the three factors are statistically significant at 5% level. The simulation for the large size problems is conducted to show having the similar computational results like the small size problems.