• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.305-314
• /
• 2012

The purpose of this study was to investigate the effects of joint kinetics and coordination on within-individual differences in maximum vertical jump. 10 male subjects aged 20 to 30 performed six trials in maximum vertical jump and with based on jump height the good(GP) and bad(BP) performances for each subject were compared on joint kinetics of lower extremity and coordination parameters such as joint reverse and relative phase. The results showed that maximum moment, power, and work done of hip joint and maximum moment of ankle joint in GP were significantly higher than that in the BP but no significant differences for the knee joint. We could observe a significant difference in joint reverse timing between both conditions. And also the relative phase on ankle-knee and ankle-hip in GP were significantly lower than that in the BP, which means that in GP joint movements were more in-phase synchronized mode. In conclusion, mechanical outputs of hip and ankle joints had an effect on within-individual differences in vertical jump and the inter-joint coordination and coordination including sequence and timing of joint motion also might be high influential factors on the performances within individual.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.5 no.1
• /
• pp.17-22
• /
• 1972

This results concerning the growth of transplanting of the oyster seed, Crassostrea angulata and Ostrea Iurida, which were transplanted from Japan by air, and cultivated by the raft suspended method at the coast of Yeongoo-Ri, Koje-Goon, located on the southern coast of Korea from January to December 1970, are as follows, 1. The mean shell height of O. lurida was 36.4mm, and the shape of the shell was round and small. On the other hand, the mean shell height of C. angulata was 87.4mm and the shell length was 52.3mm, and the shape of the shell was oval and large, 2. O. lurida and C. angulata oysters grew well when the water temperature was above $16^{\circ}C$ and the specific gravity ranged from 1.0171 to 1.0236 from June to July. 3. There was a little difference in relative valiance between shell length and height of O, lurida but significant difference was shown in C. angulata from July to November. 4. The mortality rate of O. lurida was $35.2\%$ and that of C. angulata was $21.7\%$ respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.12-20
• /
• 2008

Radial and vertical variations of relative crystallinity and crystallite width of cellulose within stems of three softwoods (Pinus densiflora S. et Z., P. koraiensis S. et Z, P. rigida Mill.) grown in Korea were examined by an X-ray diffraction method. The mean of relative crystallinity was 61.7% in P. koraiensis, 60.6% in P. densiflora and 49.4% in P. rigida. The degree of crystallinity in earlywood and latewood increased with the age from pith to about 10~15 years, and then remained almost constant value. The relative crystallinitiy of latewood was slightly higher than that of earlywood. The relative crystallinity in P. densiflora was a little lower at the base of stem, but no significant difference by height was shown in P. koraiensis and P. rigida. The crystallite widths in the stems were 2.8 to 3.0 nm, but were not significantly different in earlywood and latewood by height. In conclusion, the relative crystallinity appeared to be a useful index for separating juvenile wood from adult wood in the softwoods of P. densiflora, P. koraiensis, and P. rigida grown in Korea.

• Korean Journal of Remote Sensing
• /
• v.33 no.6_2
• /
• pp.1151-1157
• /
• 2017

Street Trees is an important object for urban environment improvement. Especially the height of the trees needs to be precisely measured as a factor that greatly influences the removal of air pollutants in the Urban Street Canyons. In this study, we extracted the height of the tree based on the stereo image using the precisely adjusted UAV Images of the target area. The adjustment of UAV image was applied photogrammetric SfM (Structure from motion) based on the collinear condition. We measured the height of the trees on the Street Canyon using stereoscopic vision on stereo plotting system. We also acquired the height of the building adjacent to the street trees and the average height of the road surface was calculated for accurate measurement of the height of each object. Through the visual analysis with the plotting operation system, it was possible to measure height of the tree and to calculate the relative height difference value with building quickly. This means that the height of buildings and trees can be calculated without making a 3D point cloud of UAV and it has the advantage of being able to utilize non-experts. In the future, further studies for semiautomatic/automation of this technique should be performed. The development and research of these technologies is expected to help to understand the current status of environmental policies and roadside trees in urban areas.

• The Korean Journal of Ecology
• /
• v.27 no.3
• /
• pp.147-153
• /
• 2004

The objective of this study was to understand differences among three half-sib families of Betula schmidtii seedlings in the effect of three Cd levels on growth and photosynthesis. One-year-old seedlings of B. schmidtii were treated with 0, 0.4 and 0.8 mM CdSO$_4$ㆍ8/3$H_2O$ for two months. Growth and physiological responses to Cd treatment levels of three families determined using dry weight, relative height growth rate(RHGR), apparent quantum yield and carboxylation efficiency. The B. schmidtii seedlings exposed to 0.4 and 0.8 mM Cd showed statisticall significant decrease in dry weight and RHGR relative to controls. In addition, the growth inhibition of B. schmidtii seedlings was accompanied by a significant decrease in net photosynthesis measured as $CO_2$ assimilation. Apparent quantum yield and carboxylation efficiency were also affected by Cd treatment, undergoing a significant and progressive reduction with increasing Cd concentrations in all families. We also found significant difference among three families of B. schmidtii in growth, biomass and photosynthesis when exposed to Cd stress. Therefore the present study showed that the difference in Cd tolerance among families might be attributed to genetic factor in response to Cd stress.

• Journal of Environmental Science International
• /
• v.23 no.6
• /
• pp.1075-1083
• /
• 2014

The objective of this study was to evaluate the effect of cutting types on microclimate and growth characteristics of afforested tree in Quercus acutissima stand after different types of cutting. The difference in temperature reaching $5.2^{\circ}C$ was shown in between clear cutting and selective cutting treatments. On July and August days with temperatures more than $35^{\circ}C$ often appeared in clear cutting stand. The values of VPD in July and August were higher than those in other months. Maximum VPD of 3.99 kPa was shown in clear cutting stand on May 23 as a prolonged rainless days appeared. However, VPD in selective cutting stand always stayed under 3.0 kPa throughout growing season. A higher intensity was shown in clear cutting and strip clear cutting stands, reaching to more than $1,600{\mu}mol\;m^{-2}s^{-1}$ at midday on early August, while that in selective cutting stand stayed about 1,500. In relative growth rate selective cutting stand showed a significantly higher relative growth rate in plant height than those in other cutting stands (p<0.05). The number of leaf in current-year branches significantly increased in selective cutting stand, whereas no increase was shown in clear cutting and strip clear cutting stands (p<0.05). In addition, relative elongation rate of current year branch also showed higher values in selective cutting stand compared with that in strip clear cutting stand (p<0.05). However, leaf mass per unit area (LMA) was higher in order of strip clear cutting, clear cutting, and selective cutting stands. From these results it is concluded that environmental conditions in clear cutting and strip clear cutting stands during growing season are more stressful to afforested tree species, resulting in lower relative growth in plant height, elongation of current-year branches, and leaf number per branch compared with those in selective cutting stand. Consequently, more data must be accumulated in the field to find out best cutting type in plantation considering the adaptational characteristic of each tree species varies with species and life span of tree is long.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.37 no.3
• /
• pp.201-207
• /
• 2017

Hay-making is one of the most common forage preservation practices in livestock operations. The objective of hay-making is to minimize nutrient loss by shortening field drying time. Measuring the impacts of cutting height of forage crop is necessary to optimize hay production balancing yield and quality, in order to obtain substantial biomass increase through harvest of regrowth. This experiment was conducted to investigate the impact of cutting height of rye (Secale cereale L.) on drying rate and hay quality. Heading stage rye was harvested at 8cm or 15cm stubble heights. Hay was daily tedded at 09:00 and sampled at 09:00, 13:00 and 17:00 to determine moisture content (MC). After two month of preservation, CP (crude protein), ADF (acid detergent fiber), NDF (neutral detergent fiber), IVDMD (in vitro dry matter disappearance), TDN (total digestible nutrient), RFV (relative feed value), DM (dry matter) loss, visual scores and total fungi count were determined for estimation of hay quality. Cutting height at 15cm could enhance the drying rate and CP content (p<0.05), but also increases DM loss (p<0.05) compared to cutting at 8cm. Cutting heights did not affect ADF, NDF, IVDMD, TDN and RFV value (p>0.05). Visual scores of rye hays cutting at 8cm and 15cm, ranged from 83 to 85. Cutting at 8cm tended to maintain higher core bale temperature and fungal count than cutting at 15cm during preservation, but there was no significant difference.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.41 no.3
• /
• pp.147-154
• /
• 2021

Cutting management has been identified as a critical factor in the alfalfa production systems because it has a significant impact on maximizing yield and maintaining the forage quality. The objective of this experiment was to determine the proper cutting height according to harvesting time for optimizing nutrient yield and forage nutritive quality of alfalfa grown in alpine regions of Korea. Alfalfa was sown at a seeding rate of 30 kg/ha in August 2018 and harvested at four cuttings in 2019 (3 May, 2 July, 11 September, and 13 October). Cutting heights were adjusted at 5, 15, and 25 cm above the soil surface. Alfalfa plant was tallest at the third cutting (109 cm), which was on average 35 cm taller than the first or second cutting. Relative feed value (RFV) remained unaffected by cutting height at the first harvest, but increased consistently in subsequent harvests as cutting height increased. Alfalfa collected at the first and fourth cuttings had the highest RFV (mean 152), which was on average 8 and 67 units higher than the second and third harvests, respectively. At each harvest, in vitro dry matter digestibility was highest in alfalfa cut at a 25-cm height. Dry matter (DM) production at each cutting height was highest in the first cutting, accounting for on average 36-37% of total annual DM production, and lowest in the fourth harvest, accounting for about 11-13% of the total DM yield. The total dry matter production (in four harvests) was 4,218 kg/ha higher when alfalfa was subjected to a cutting height of 5 cm rather than 25 cm. Cutting height had no effect on total crude protein yield, but from the first to fourth cutting, the protein yield followed a decreasing trend. Finally, there were visible declines in forage nutritive quality when alfalfa was cut at a shorter height. However, the magnitude of difference in total forage yield may outweigh the slight decline in forage quality when alfalfa is cut at a lower height. The findings of this study could help the alfalfa growers make better harvest management decisions.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2343-2350
• /
• 2013

The wave height distributions in front of a vertically perforated wall structures for obliquely incident uni-directional irregular waves are mainly investigated by using 3D hydraulic experiments. The difference and similarity of wave propagation along the plain and perforated wall structures are investigated and particularly the effects of side walls in chamber and relative chamber width are analyzed. This study shows that the wave height distribution patterns for normalized wave heights in front of structure is significantly different between the plain and perforated wall structures, and the side wall in the chamber suppresses the growth of waves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.7
• /
• pp.1047-1054
• /
• 2001

Atomic Force Microscope (AFM) was used to study cross sectional profiles and dimensions of fatigue striations in 2017-T351 aluminum alloy. Their widths(SW) and heights (SH, SH(sub)h, SH(sub)ι) were measured from the cross sectional profiles of three-dimension AFM images. The following results that will be helpful to understand the fatigue crack growth mechanism were obtained. (1) The relation of SH=$\alpha$(SW)(sup)1.2 was obtained. (2) The ratio of the striation height to its width SH/SW, SH(sub)h/SW and SH(sub)ι/SW did not depend on the stress intensity factor range ΔK and the stress ratio R( =P(sub)min/P(sub)max = K(sub)min/K(sub)max). (3) Effect of precipitate on the morphology of striation was changed by the relative dimensional difference between the striation width SW and the precipitates. From these results, the applicability of the AFM to nano-fractography is discussed.