• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.56 no.2
• /
• pp.99-106
• /
• 2011

Here we reported an analyzing result for the relationship between climatic variables and rice(c.v. Odaebyeo and Ilpumbyeo) yield characteristics (including some growth characteristics) based on a long-term observed data at GARES and at KMA for rice and weather, respectively. Most of crop parameters investigated, such as heading date, culm height, panicle number $m^{-2}$, grain number $panicle^{-1}$ ripening rate, 1,000 grain weight and yield were strongly affected by wind velocity and relative humidity, as well as by daily mean air temperature, precipitation, sunshine hours and daily variations in air temperature depending on variety and crop developmental stages. Air velocity and relative humidity had not been studied as climatic variables affecting on the characteristics of rice growth and yield, however, they turned out to affect all the characteristics of rice investigated, especially ripening rate and yield, as much as any other climatic variables in this study. Air velocity appeared to affect highly the culm height and yield of Odaebyeo and ilpumbyeo. Relative humidity appeared to affect highly grain number and ripening rate of Odaebyeo and yield of Ilpumbyeo. Consequently Rice yield revealed to increase in the climatic conditions of high air velocity and low relative humidity.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.51-55
• /
• 2004

In this study, the levelling and the GPS levelling were carried out with 6 points in 2km${\times}$2km area and the results were analysed. As a result of this research, we had to observe more than 15 minutes to get the height accuracy of 10mm by single frequency GPS receiver in relative surveying. We could not get more better accuracy than 10mm. we could get the height accuracy of within 10mm from observing only more than 5 minutes by double frequency GPS receiver, and of within about 3mm from observing more than 10 minutes. When the number of fixed points is within 3, the level net adjustment result is very close to the one of direct levelling survey. When the number of fixed points is 3, the less the area of triangle the better the adjustment result, and the case of including measure point has more better accuracy than that of non-including measure point.

• Analytical Science and Technology
• /
• v.6 no.4
• /
• pp.359-362
• /
• 1993

To find compromise experimental conditions that will allow a group of elements to be run on flame atomic absorption spectrometer without changing the burner height or gas flow rates, measurements were carried out. The optimum absorbance for simultaneous analysis of ten elements was observed at high flow rate of air-$C_2H_2$ as fuel and at 2mm of burner height. At the condition, 73% of mean relative absorbance were achieved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.3
• /
• pp.296-303
• /
• 2004

The heat and flow characteristics in a single-phase parallel-flow heat exchanger was examined numerically to obtain its optimal shape. A response surface method was introduced to approximately predict its performance with respect to the design parameters over the design domain. The inflow/outflow angle of the working fluid, the location of inlet/outlet, the protruding height of flat tube and the height of header were chosen as a design parameter The evaluation of the relative importance of the design parameters was performed based on a sensitivity analysis. An efficiency index was used as an evaluation characteristics value to simultaneously consider both the heat transfer and the pressure drop. The efficiency index of the optimum model, compared to that of the base model, was increased by 9.3%.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.6 no.1
• /
• pp.37-40
• /
• 2000

This study was carried out to investigate dropping shock of household electric appliances during materials handling. Microwave oven($18{\ell}$), TV(16") and washing machine(6.2kg) were singled out as the study items. From the results of dropping test by KS A 1026(General Rules of Performance Testing for Packaged Freights), relative equations were gained as follow : y=0.0863x+10.032 for microwave oven, y=0.136x+7.85 for TV and y=0.214x+5.8 for washing machine (where y is G-factor and x is Dropping height). The maximum values of dropping shock during materials handling were measured to be $11{\sim}14G$ for microwave oven, $12{\sim}15G$ for TV and $10{\sim}12G$ for washing machine. The maximum shocks of microwave oven, TV and washing machine during materials handling were corresponding to dropping shocks of dropping height 45.98cm, 52.57cm and 28.97cm by KS A 1026.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.407-415
• /
• 2002

In this paper, mutual coupling effect between antennas mounted on UAV(Unmanned Air Vehicle), operating In different frequency bands, is calculated for supposing efficient arrangement. For the calculation, FDTD method is used, simulation parameters are confined to distance between antennas, height of antennas, types of ground, etc. The simulation data are compared with those of other numerical method to confirm accuracy of the results. It is appeared that the critical factor of mutual coupling is height of an antenna relative to that of the other antenna.

• Childhood Kidney Diseases
• /
• v.13 no.1
• /
• pp.14-20
• /
• 2009

Growth retardation is a common consequenc of chronic kidney disease (CKD) in childhood. Many recent clinical and experimental data indicate that growth failure in CKD is mainly due to a relative GH insensitivity and functional IGF-I deficiency. Glucocorticoids also glucocorticoids interfere with the integrity of the somatotropic hormone axis at various levels. Over the past 10 years, recombinant growth hormone (rhGH) has been used to help short children with chronic kidney disease. A GH dosage of 0.35 mg/kg/week (28 IU/$m^2$/week) appears efficient and safe. Some clinical trial data show that final height will be within the normal target height range when GH treatment is continued for many years without remarkable adverse events.

• Journal of Plant Biology
• /
• v.22 no.3
• /
• pp.59-62
• /
• 1979

Distribution and standing crops of seedling and sapling as undergrowing tree were investigated in a Pinus rigida forest. The relative light intensity(RLI) on the ground level was 3.9∼59.3% which indicates a wide range. Under this range of RLI seedlings and saplings distribute well in the stand. Eight trees were selected from the stand, then measured dry weight of stem, branches and leaves using thestratified clip technique. A possible relationship between the diameter at the bottom of the tree (Do) and standing crops was investigated. As Do increased from 0.8cm (T1) to 7.2cm (T8), the standing crops also increased from 42.6g to 7,410.4g. Since semi-log values between Do and standing crops clearly indicates a straight line, there is close relationship between these two factors. Therefore it is possible to estimate the standing crops of seedling and sapling by measuring Do. Productive structure shows that phytosynthetic layer is located above the 1/2 height of the tree and maximum photosynthetic layer apperars on 2/3 level in height.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.45-50
• /
• 1997

In recent years the recording density of hard disk has been increasing largely due to the decreasing flying height of head. However, as the flying height is decreased the reliability issue becomes ever more critical. This is because the reliability and durability of hard disk is related to the head/disk interaction as the two components come into partial or full contact. In this work characteristics of friction and stiction in head/disk interface was investigated using constant speed drag test and CSS(contact-start-stop) test. The purpose of this research is to identify the frictional properties of head/disk interface

• Transactions of Materials Processing
• /
• v.17 no.3
• /
• pp.203-209
• /
• 2008

In this paper, experimental investigation has been performed to analyze the forming process of toothed or serrated sheets, which is used as strap engaging surface of the seal to secure together overlapping portions of steel or plastic strapping ligature. Serration formed on the strap engaging surface of the seal prevent from relative slipping between overlapping ligatures after closing the seal. The geometry of tooth on the strap engaging surface is directly related to the quality of securing overlapping ligatures together. Inclined indentation followed by scratching operation has been proposed and applied to the experiments. Punch entry and face angles are selected as process variables to see the influence of these variables on the tooth geometry. Five different punch entry angles have been applied to experiments and three different punch face angles have been selected for each case of punch entry angle. Clay is selected as model material for experiments. Experimental results are summarized in terms of tooth height, tooth width, and aspect ratio such as tooth height to width ratio, respectively.