• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.4
• /
• pp.341-349
• /
• 2004

In this paper, the decentralized neural network control of the reference compensation technique is proposed to control a 2-DOF inverted pendulum on an x-y plane. The cart with the 2-DOF inverted pendulum moves on the x-y plane and the 2-DOF inverted pendulum rotates freely on the x-y axis. Since the 2-DOF inverted pendulum is divided into two 1-DOF inverted pendulums, the decentralized neural network control is applied not only to balance the angle of pendulum, but also to control the position tracking of the cart. Especially, a circular trajectory tracking is tested for position tracking control of the cart while maintaining the angle of the pendulum. Experimental results show that position control of the inverted pendulum system is successful.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.698-701
• /
• 1996

A novel neural network control scheme is proposed to identify the inverse dynamic model of robot manipulator and to compensate for uncertainties in robot dynamics. The proposed controller is called reference compensation technique(RCT) by compensating at reference input trajectory. The proposed RCT scheme has many benefits due to the differences in compensating position and learning algorithm. Since the compensation is done outside the plant it can be applied to many control systems without modifying the inside controller. It performs well with low controller gain because the operating range of input values is small and the output of the neural network controller is amplified through the controller gain. The back-propagation algorithm is used to train and simulations of three link robot manipulator are carried out to prove the proposed controller's performances.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.5
• /
• pp.367-375
• /
• 2022

Generally, a proportional-resonant controller is used to eliminate steady-state errors during the voltage-current control of a double-conversion uninterruptible power supply (UPS) in a stationary reference frame. Additionally, the feed-forward control compensating for the load current, which can be considered a disturbance of the voltage controller, can be used to improve the disturbance rejection performance. However, during the parallel operation of UPSs, circulating current can occur between UPS modules when performing both feed-forward control and droop control because feed-forward control reduces the circulating current impedance. This study proposes a feed-forward compensation technique that considers the impedance of circulating current. An additional feed-forward compensation technique is developed to enhance the disturbance rejection performance. The validity of the proposed feed-forward compensation technique is verified by the experiment results of the parallel operation of a 500 W double-conversion UPS module.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1887-1893
• /
• 2016

The VSA(Video Signal Analysis) method is the time-domain approach for estimating ultrasonic attenuation which utilizes the envelop signals from backscattered rf signals. The echogenicity of backscattered ultrasonic signals, however, from deeper depths are distorted when the broadband transmit pulse is used and it degrades the estimation accuracy of attenuation coefficients. We propose the modified VSA method using adaptive bandpass filters according to the centroid shift of echo signals as a pulse propagates. The technique of dual-reference diffraction compensation is also proposed to minimize the estimation errors because the difference of attenuation properties between the reference and sample aggravates the estimation accuracy when the differences are accumulated in deeper depth. The proposed techniques minimize the distortion of relative echogenicity and maximize the signal-to-noise ratio at the given depth. Simulation results for numerical tissue-mimicking phantoms show that the Rectangular-shaped filter with the appropriate center frequency exhibits the best estimation performance and the technique of the dual-reference diffraction compensation dramatically improves accuracy for the region after the beam focus.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.76.3-76
• /
• 2001

In this paper, an adaptive disturbance compensation technique is used in a tracking problem, under which the tracking reference is unknown. Based on a simple disturbance observer that effectively estimates the low frequency components of disturbance, the feedforward compensation is applied in addition to the conventional feedback control. Under the proposed compensation method, sensitivity analysis is given to illustrate the effectiveness. Finally, the proposed method is applied to the tracking problem in an optical storage system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.148-149
• /
• 2008

As infrared light is radiated, the CMOS Readout IC (ROIC) for the microbolometer type infrared sensor detects voltage or current when the resistance value in the bolometer sensor varies. One of the serious problems in designing the ROIC is that resistances in the bolometer and reference resistor have process variation. This means that each pixel does not have the same resistance, causing serious fixed pattern noise problems in sensor operations. In this paper, Reference resistor compensation technique was proposed. This technique is to compensate the reference resistance considering the process variation, and it has the same reference resistance value as a bolometer cell resistance by using a comparator and a cross coupled latch.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1707-1713
• /
• 2016

This paper proposes a dc error compensation algorithm using dq-synchronous coordinate transform digital phase-locked-loop in single-phase grid-connected converters. The dc errors are caused by analog to digital conversion and grid voltage during measurement. If the dc offset error is included in the phase-locked-loop system, it can cause distortion in the grid angle estimation with phase-locked-loop. Accordingly, recent study has dealt with the integral technique using the synchronous reference frame phase-locked-loop method. However, dynamic response is slow because it requires to monitor one period of grid voltage. In this paper, the dc offset error compensation algorithm of the improved response characteristic is proposed by using the synchronous reference frame phase-locked-loop. The simulation and the experimental results are presented to demonstrate the effectiveness of the proposed dc offset error compensation algorithm.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.221-229
• /
• 2013

In this paper, the image formation by the motion compensation technique for Synthetic Aperture Radar system(SAR) were realized through the computer simulation. The motion compensation technique performed image data with the range compression, the compensation procedure, the azimuth compensation and the noise elimination procedure. The range compression procedure transform the SAR raw data into the frequency domain and correlate with the range reference function and then inversely transform into the time domain. The compensation procedure contain the aircraft fluctuations compensation and the radar image degrading effect elimination procedure which was caused by image formation algorithm itself. The aircraft fluctuations compensation procedure perform the first stage which correct the phase angle and the second stage which calculate the Doppler frequency and determine the coordinate of the received signal. The radar image degrading effect elimination procedure also perform range migration compensation and the image defocussing effect compensation. The azimuth compression procedure transform the compensation data to the frequency domain and correlate with the azimuth reference function. The azimuth correlated data are inversely transformed to the time domain which is called SAR image data. When the above procedure were completed, the image data contains the received signals mixed with noise. The threshold technique was applied to elimination the noise from the mixed image data.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2562-2564
• /
• 2002

This paper presents an auxiliary beam-assisted adaptive compensation technique applied to alleviate the problem of LDV's body vibration. The LMS algorithm is applied to adaptively compensate the body vibration utilizing the reference signal provided by the auxiliary beam. The usefulness of the proposed technique is verified via computer simulations performed for diverse types of target signals and body vibration.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2183-2185
• /
• 2000

This paper presents an auxiliary beam-assisted adaptive compensation technique applied to alleviate the problem of LDV's body vibration. The LMS algorithm is applied to adaptively compensate the body vibration utilizing the reference signal provided by the auxiliary beam. The usefulness of the proposed technique is verified via computer simulations performed for diverse types of target signals and body vibration.