• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.616-618
• /
• 1996

This paper presents an unipolar PWM which commutated switching device only in a half period. This method reduced switching loss significantly because of decreasing switching number in n period. In high speed motor drive needed high frequency above 300 Hz fundamental frequency, this method is suited very well. This paper described the principle of unipolar PWM method, analyzed harmonic spectrum and compared with bipolar PWM, Modified PWM and Overmodulation method in switching loss.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.243-246
• /
• 1997

In this paper, soft switching high power factor buck converter is proposed. This converter is composed of diode rectifier, a input capacitor can be small enough to filter input capacitor can be small enough to filter input current, buck converter with loss less snubber circuit. Converter is operated in discontinous conduction mode, turn of of the switching device is a zero current switching(ZCS) and high power factor input is obtained. In addition, zero voltage switching(ZVS) at turn of is achieved and switching loss is reduced using loss less snubber circuit. The capacitor used in the snubber circuit raised output voltage. Therefore, proposed converter has higher output voltage and higher efficiency than conventional buck type converter at same duty factor in discontious conduction mode operation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.51-54
• /
• 2005

Generator efficiency optimization is important for economic saving and environmental pollution reduction. In general, the machine loss can be reduced by the decreasing the flux level, resulting in the significant reduction of the core loss. This paper proposesan model-based controller is used to decrement the excitation current component on the basis of measured stator current and machine parameters and the q-axis current component controls the generator torque, by which the speed of the induction generator iscontrolled according to the variation of the wind speed in order to produce the maximum output power. The generator reference speed is adjusted according to the optimum tip-speed ratio. The generated power flows into the utility grid through the back-to-back PWM converter. The grid-side converter controls the dc link voltage and the line-side power factor by the q-axis and the d-axis current control, respectively. Experimental results are shown to verify the validity of the proposed scheme.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.23-28
• /
• 1996

The potential for the RELAP5/MOD3.2 was assessed for the loss-of-RHR event during the mid-loop operation and the predictability of major thermal-hydraulic phenomena was also evaluated for the long term transient. The analysis results of the typical two cases(cold leg opening case and pressurizer opening case) were compared with experimental data which was conducted at ROSA-IV/LSTF in Japan. As a result, it was shown that tile code was capable of simulating the thermal-hydraulic transport process with appropriate time step during the reduced inventory operation with the loss-of- RHR system.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.2110-2121
• /
• 1993

A numerical investigation has been carried out for the flow characteristics after exchange of some filters from the original layer to the new low pressure loss layer with equal filtering efficiency. The solution domain includes upper plenum, filter layer, clean space, access panels, and lower plenum. The concept of the distributed pressure resistance was applied to describe the momentum loss in filter layer and access panels. The evolution of the flow field is simulated using the low Reynolds number k-.epsilon. over bar turbulent model and SIMPLE algorithm based on the finite volume method. As a result, after the exchange of filter layer the power requirement can be reduced by 8-9 percent. The results also demonstrate that the perpendicularity of the flow near access panels may become worse at new filter layer than origianl filter layer. But the situation can be recovered by adjusting the jopening ratio of access panels.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1021-1022
• /
• 2011

This paper presents the double side PM synchronous motor/generator for core loss reduction in flywheel energy storage system. The use of double PM rotor causes the elimination of core loss in no-load state of machine. Because flywheel rotational speed is reduced by core loss, double PM rotor is very effective in flywheel system. This paper suggests two types of double side PM rotor, Halbach magnetized array and parallel magnetized array. And characteristic comparison according to thickness of rotor back core is performed.

• ETRI Journal
• /
• 제33권1호
• /
• pp.1-5
• /
• 2011

Downlink transmit power allocation schemes are proposed for soft fractional frequency reuse (FFR) in loose and tightly coordinated systems. The transmit powers are allocated so that the loss of spectral efficiency from the soft FFR is minimized, and the required cell edge user throughput is guaranteed. The effect of the soft FFR on spectral efficiency is evaluated depending on the power allocation schemes and the number of subbands. Results show that the loss of spectral efficiency from the soft FFR can be reduced by configuring an appropriate number of subbands in the loosely coordinated systems. In tightly coordinated systems, results show that the loss of spectral efficiency can be minimized regardless of the number of subbands due to its fast coordination.

• 대한산업공학회지
• /
• 제15권2호
• /
• pp.57-64
• /
• 1989

An Economic selection of specification limits is considered for a given target value in a complete inspection plan. Each item is inspected, and if it meets the specification, it is accepted. Items less than the lower specification limit are scrapped or sold at a reduced price, and those greater than the upper specification limit are reworked. Cost factors to be considered are economic loss caused by quality deviations, rework cost and scrapping cost. Methods for finding the optimal specification limits are given for the cases of piecewise linear loss function and quadratic loss function with illustrative examples.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.97-107
• /
• 1998

Three different kinds of brake discs including two coated brake discs and one steel disc were tested under the same experimental conditions on a reduced scale braking test bench. Braking test bench was specially designed to analyse thermo-mechanical and frictional behaviors of two sizes of brake discs in stop and hold braking modes. And Plasma spray coating technique was used to coat ceramic powder on the discs. In the test four commercial brake pads were coupled with discs. Ceramic coated discs had shown good stability in friction coefficient at high speed and high energy braking conditions. But they caused large pad mass wear loss compared with the steel disc. It was shown that thermal barrier effect in ceramic coated discs adjusted the thermal partition between pad and disc. For a steel disc, it had shown fluctuating friction coefficient at high speed but a fittie pad mass wear loss compared with ceramic coated discs.

• 대한인간공학회지
• /
• 제15권2호
• /
• pp.113-124
• /
• 1996

This study was initiated to suggest the optimal size intervals for mail-order clothing. The questionnaire survey was carried at 360 women and 50 men who purchased apparels by mail-order. The garment sizes providing at the various mail-order companies in Korea were compared. The garment sizes that consumers wanted to purchase were also investigated. The collected data were analyzed and optimal size intervals for mail-order clothing were decided by the loss function. The results are as follow. 1) The optimal size intervals were varied from 4cm to 7cm. The total expected loss of the apparel sizes suggested in this study was less than that of the current mail-order apparel sizes. When the number of sizes for mail-order clothing is increased, the expected loss was reduced considerably. 2) The mail-order clothing is made for consumers with average body size. 30 The number of garment sizes available by mail-order was under three. 4) Subjects tend to select larger size garments, when the right size garments are not available.