• 한국강구조학회 논문집
• /
• 제19권5호
• /
• pp.527-537
• /
• 2007

H형강 교량은 공장에서 압연 제작한 H형강을 주형과 가로보로 사용함에 따라 품질 및 관리가 용이하고 공장제작으로 현장작업 및 공사기간의 단축과 보강재의 설치량이 적은 단순하고 경제적인 교량형식이다. 본 연구는 기존 H형강 교량의 지간 및 단면 효율 개선을 위한 방법으로 다단계 온도프리스트레싱(Multi-Stepwise TPSM) 공법을 H형강 교량에 적용하여 도입효과 및 적용지간을 분석하였다. 구조해석결과 H형강교의 다단계 온도프리스트레싱 효과는 H-$900{\times}300$형강을 이용한 30m 5주형 H형강교량을 기준으로 기존 플레이트 거더 교량의 높이를 50.7~55.1%, 중량을 24.1~26.2% 수준으로 감소시킬 수 있는 것으로 평가되었다. 또한 7주형 H형강교량의 주형수를 5주형으로 감소시켜 경제적인 교량건설이 가능한 것으로 나타나 온도프리스트레싱이 도입된 H형강 교량은 기존 H형강과 비교하여 중소지간용 교량으로 충분한 경제성을 가질 수 있을 것으로 판단된다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.76-78
• /
• 2004

The phenomenon of weld shrinkage mainly occurs owing to residual stress by heating, which largely effects on welding quality, Actually as the shrinkage rate depends on the weld deposit amount, so it is desired that the sectional area of weld joint shall be reduced. In this respect the Electron beam welding has more profitable position compare to Narrow-gap TIG welding which is even superior to other arc welding processes. In case of thick austenitic stainless steel the shrinkage rate of Electron beam welding has about $10\%$ of Narrow-gap TIG welding's, which means that residual stress is a lot less than that of Narrow-gap TIG welding. And heat input and welded section area also indicate large difference between two processes.

• Structural Engineering and Mechanics
• /
• 제73권6호
• /
• pp.613-620
• /
• 2020

The research study is focuses on a form of all-bolted joint with the external ring stiffening plate in the prefabricated steel structure. The components are bolted at site after being fabricated in the factory. Six specimens were tested under cyclic loading, and the effects of column axial compression ratio, concrete-filled column, beam flange sub plate, beam web angle cleats, and spliced column on the failure mode, hysteretic behavior and ductility of the joints were analyzed. The results shown that the proposed all-bolted joint with external ring stiffening plate performed high bearing capability, stable inflexibility degradation, high ductility and plump hysteretic curve. The primary failure modes were bucking at beam end, cracking at the variable section of the external ring stiffening plate, and finally welds fracturing between external ring stiffening plate and column wall. The bearing capability of the joints reduced with the axial compression ratio increased. The use of concrete-filled steel tube column can increase the bearing capability of joints. The existence of the beam flange sub plate, and beam web angle cleat improves the energy dissipation, ductility, bearing capacity and original rigidity of the joint, but also increase the stress concentration at the variable section of the external reinforcing ring plate. The proposed joints with spliced column also performed desirable integrity, large bearing capacity, initial stiffness and energy dissipation capacity for engineering application by reasonable design.

• 산업기술연구
• /
• 제22권A호
• /
• pp.177-184
• /
• 2002

Reinforced concrete(R/C) is commonly used to structures because they have many merits that compressive strength, economy and so on. However, reinforced concrete has a crack at the tensile section which is due to the relatively lower tensile strength than its compressive strength Latex modified concrete(LMC) has higher tensile and flexural strength than the ordinary portland cement, due to the interconnections of hydrated cement and aggregates by a film of latex particles. The purpose of this study was to investigate the flexural behavior of reinforced concrete beam with latex modified concrete, having the main experimental variables such as concrete types(ordinary portland cement concrete, latex modified concrete), latex contents(0%, 15%), flexural steel ratios(0.012, 0.0235), and with/without shear reinforcement. The beam of LMC showed considerably higher initial cracking loads and ductility than that of OPC, but, similar to ultimate strength and deflection. This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation. The beam with latex modified concrete could be adopted at field for controlling and reducing the tensile crack due to its higher tensile strength.

• 한국강구조학회 논문집
• /
• 제20권3호
• /
• pp.445-454
• /
• 2008

철골모멘트접합부에 관한 이전의 연구에 의하면 RHS 기둥과 기존의 스캘럽을 가진 접합부실험체의 변형능력은 매우 열등했고, 보단부의 응력집중은 보에서 기둥으로 전달되는 모멘트의 전달효율에 영향을 받는다는 사실을 실험이나 해석적으로 밝혔다. 본 연구는 보강된 RBS 접합부와 용접수평스티프너를 사용한 효고현남부지진 이전에 지어진 모멘트 접합부를 내진보강하는데 주안점을 두었다. 이러한 내진보강은 시공성과 경제성을 고려하여 보의 하부플랜지에만 실시하였다. 접합부의 내진보강방법을 발견하고 이를 향상시키기 위해서 비선형유한요소해석을 통해서 다양한 변수를 바탕으로 한 파라메타 연구를 실시하였다.

• 한국건축시공학회지
• /
• 제8권5호
• /
• pp.43-51
• /
• 2008

This study examines shear capacity performance and structural characteristics of reinforced concrete beam using carbon fiber sheet(CFS), g)ass fiber sheet(GFS), glass fiber steel plate(GSP) and carbon fiber bar CB) which are reinforcing materials for reinforced concrete beam in order to produce similar condition to repair and reinforce actual structure and aims to provide data available In designing and constructing reinforced concrete structures under the structural damage. This study obtains the following conclusions. After considering the shear experiment results. it was indicated that the CB reinforced test object was the best in the shear capacity improvement and ductility capacity as it was contained in the concrete and was all operated, Also, GFS reinforced test object indicated the reduced flexural capacity but good shear capacity. GSP reinforced test object had bigger reinforcing strength than other reinforcing test objects. On the other hand, it showed the lowest reinforcement effect as compared section thickness of reinforced material because it showed the bigger relativity a section thickness of reinforced material. If the adherence to the concrete is improved, it will seem to show bigger reinforcement effect.

• Wind and Structures
• /
• 제23권5호
• /
• pp.405-420
• /
• 2016

Section model wind tunnel test is currently the main technique to investigate the flutter performance of long-span bridges. Further study about applying the wind tunnel test results to the aerodynamic optimization is still needed. Systematical parameters and test principle of the bridge section model are determined by using three long-span steel truss suspension bridges. The flutter critical wind at different attack angles is obtained through section model flutter test. Under the most unfavorable working condition, tests to investigate the effects that upper central stabilized plate, lower central stabilized plate and horizontal stabilized plate have on the flutter performance of the main beam were conducted. According to the test results, the optimal aerodynamic measure was chosen to meet the requirements of the bridge wind resistance in consideration of safety, economy and aesthetics. At last the credibility of the results is confirmed by full bridge aerodynamic elastic model test. That the flutter reduced wind speed of long-span steel truss suspension bridges stays approximately between 4 to 5 is concluded as a reference for the investigation of the flutter performance of future similar steel truss girder suspension bridges.

• 한국강구조학회 논문집
• /
• 제16권2호통권69호
• /
• pp.247-255
• /
• 2004

본 실험프로그램은 슬래브가 있는 합성보의 내진성능향상을 위해 기존 모멘트접합부의 내진보강 방법을 개발을 목적으로 수행하였다. 반복하중을 통해 5개의 실대형 합성실험체에 대한 실험을 수행하였다. 각형강관기둥과 H형강보로 이루어진 기존의 다이아프램접합부가 RBS 또는 개량수평스티프너를 통해서 하부플랜지에만 내진 보강되었다. 제안한 보강접합부의 효율성을 조사하였다. 실험결과 하부플랜지에만 RBS를 적용한 접합부는 부족한 변형성능을 나타냈지만, 개량스티프너를 적용한 합성보 접합부는 내진성능을 향상시켰다.

• 한국산학기술학회논문지
• /
• 제12권4호
• /
• pp.1552-1558
• /
• 2011

본 논문에서는 알루미늄 폼을 사용한 자동차 범퍼 빔을 설계하고 충돌해석을 수행하였다. 해석모델은 B형 단면 구조를 갖는 실제 크기의 범퍼 빔이다. 저속 정면충돌 시 알루미늄 범퍼 빔의 변형량 및 내부 에너지 거동을 예측할 수 있는 ANSYS AUTODYN을 이용하였다. 7075-T6 알루미늄 합금을 사용하여 철강 재질의 빔보다 55 %의 중량 감소를 얻을 수 있었으며 알루미늄 폼을 사용한 범퍼 빔의 변형량은 철강 빔과 비슷하지만 충돌에너지의 감소가 더 큰 것을 확인할 수 있었다. 또한, 알루미늄 폼의 완충보다는 50 % 충진 시 충돌에너지 흡수가 더 좋았다.

• Steel and Composite Structures
• /
• 제46권3호
• /
• pp.417-433
• /
• 2023

The maximum ductility and cumulative ductility of connection joints of Buckling-Restrained Braced Frames (BRBF) are critical to the structural overall performance, which should be matched with the BRB ductility. The two-story and one-span BRBF with a one-third scale was tested under cyclic quasi-static loading, and the top-flange beam splice (TFBS) rotational connections were proposed and adopted in BRBF. The deformation capacity of TFBS connections was observed during the test, and the relationship between structural global ductility and local connection ductility was studied. The rotational capacity of the beam-column connections and the stability performance of the BRBs are highly relevant to the structural overall performance. The hysteretic curves of BRBF are stable and full under large displacement demand imposed up to 2% story drift, and energy is dissipated as the large plastic deformation developed in the structural components. The BRBs acted as fuses and yielded first, and the cumulative plastic ductility (CPD) of BRBs is 972.6 of the second floor and 439.7 of the first floor, indicating the excellent energy dissipation capacity of BRBs. Structural members with good local ductility ensure the large global ductility of BRBF. The ductile capacity and hysteretic behavior of BRBF with TFBS connections were compared with those of BRBF with Reduced Beam Section (RBS) connections in terms of the experimental results.