• Computers and Concrete
• /
• v.16 no.1
• /
• pp.37-48
• /
• 2015

Alkali aggregate reaction affects numerous civil engineering structures and causes irreversible expansion and cracking. This work aims at developing model to predict the potential expansion of concrete containing alkali-reactive aggregates. First, the paper presents the experimental results concerning the influence of particle size of an alkali-reactive aggregate on mortar expansion studied at 0.15-0.80 mm, 1.25-2.50 mm and 2.5-5.0 mm size fractions and gives data necessary for model development. Results show that no expansion was measured on the mortars using small particles (0.15-0.80 mm) while the particles (1.25-2.50 mm) gave the largest expansions. Finally, model is proposed to simulate the experimental results by studying correlations between the measured expansions and the size of aggregates and to calculate the thickness of the porous zone necessary to take again all the volume of the gel created by this chemical reaction.

• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.572-579
• /
• 2009

This study is to investigate experimentally the flame structure and propagation mechanism in dust explosions and to provide the fundamental knowledge. Upward propagating laminar dust flames in a vertical duct of 1.8 m height and 0.15 m square cross-section are observed and flame front is visualized using by a high-speed video camera. Also, the thicknesses of preheated and reaction zone have been determined by a schlieren, electrostatic probe and thermocouple. The thickness of preheated zone in lycopodium dust flame is observed to be 4~13 mm, about several orders of magnitude higher than that of premixed gaseous flames. From the experimental results by a PIV(Particle Image Velocimetry) system, a certain residence time of the unburned particle in preheated zone is needed to generate combustible gas from the particle. The residence time will depend on preheated zone thickness, particle velocity and flame propagation velocity.

• The korean journal of orthodontics
• /
• v.12 no.1
• /
• pp.7-14
• /
• 1982

In this study, effects of cyclophosphamide on the growth of the mandibular condyle head were investigated with Spraque-Dawley rats of the 28 days of age. Rats were devided into four groups. Three were used as experimental groups, and one as control. Each rat in experimental group was injected intraperitoneally with cyclophosphamide repeatedly three times, 20mg/kg for the first group, 40mg/kg for the second, and 60mg/kg for the third each time. Rats in control group were injected with physiological saline in the same method. Rats in each group were sacrificed at 5, 10, and 15 days following the last injection. The specimens were stained with H-E, toluidine blue, PAS, and alcian blue. The results were as follows; 1. In experimental group, with increasing the injection doses, the thickness of the condylar cartilage from the transitional zone to the hypertrophic zone became thinner than in control group. 2. Weaker metachromasia to toluidine blue and less positive reaction to PAS were seen. 3. In primary marrow cavity the fewer trabecular was formed, The direction of trabecular formation became obscuerer, and the lower density of bone was resulted in.

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.455-463
• /
• 1994

Aluminum matrix composites reinforced by fine steel wires were fabricated by squeeze casting process. Preforms made of fine steel wires were prepared with different surface conditions, namely uncoated(TN), carbo-nitriding treated(TT), and brass coated(TA). Squeeze casting were performed under the pressure of $1500kg/cm^2$ for 3min. during solidification, and pouring temp. of the melt being $750^{\circ}C$ and the steel mold being preheated at $250^{\circ}C$. Microstructural characteristics were evaluated, particularly concerned with the effect of the surface conditions of the preforms. The results obtained from this study are like these. TN specimens show partially non-wetted regions, due to easy formation of oxides on the surface of the fine steel wires. TT specimens show no interfacial reaction between the steel wires and the aluminum alloy matrix, possibly due to the formation of carbo-nitrided zone on the surface of the steel wires. TA specimens show excellent wettabillity between the reinforced steel wires and the aluminum alloy matrix and very thin interfacial zone is formed between them. During the solution hardening treatment of TA specimens, thickness of the interfacial reaction zones were increased with the solution treating time. TA specimens show typical ductile fracture in tensile test, but TT specimens show brittle fracture possibly due to the formation of the brittle hard surface on the steel wires during carbo-nitriding treatments. TA specimens which were reinforced with 40 vol.% of the fine steel wires exhibit high tensile strength of $77.1kgf/mm^2$ and impact value of $8.1kgf-m/cm^2$.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.95-95
• /
• 2009

Zinc coatings provide the most effective and economical way of protecting steel against corrosion. There are three types of galvanizing lines typically used in production line in galvanizing industries,Galvanize (GI) coating (Zn-0.1-0.3%Al), Galfan coating (Zn-5%Al), Galvalume(GL) coating (45%Zn-Al). In continuous Galvanizing lines, the immersed bath hardware (e.g. bearings, sink, stabilizer, and corrector rolls, and also support roll arms and snout tip) are subjected to corrosion and wear failure. Understanding the reaction of these materials with the molten Zn alloy is becomes scientific and commercial interest. To investigate the reaction with molten Zn alloys, static immersion test performed for 4, 8, 16, and 24 Hr. Two different baths used for the static immersion, which are molten Zn and molten Zn-55%Al. Microstructures characterization of each of the materials and intermetallic layer formed in the reaction zone was performed using optical microscope, SEM and EDS. The thickness of the reaction layer is examined using image analysis to determine the kinetics of the reaction. The phase dominated by two distinct phase which are eutectic carbide and matrix. The morphology of the intermetallic phase formed by molten Zn is discrete phase showing high dissolution of the material, and the intermetallic phase formed by Zn-55wt%Al is continuous. Aluminum reacts readily with the materials compare to Zinc, forming iron aluminide intermetallic layer ($Fe_2Al_5$) at the interface and leaving zinc behind.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.2
• /
• pp.265-270
• /
• 1989

The present study considers the thermal structure variation in a porous medium caused by changing the most important radiative property of porous medium, absorption coefficient, as well as altering the physical dimension of porous medium and the equivalence ratio of premixed gas mixture. The radiation model was introduced as an unsteady differential form using the two-flux gray radiation model. The role of the conductive heat transfer through both gas phase and porous medium was found to be almost insignificant compared with that of the radiative heat transfer. The reaction zone shifted upstream and the flame thickness decreased as either the geometrical length of porous medium increased or the absorption coefficient decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.251-253
• /
• 2017

Numerical study of air-blast type injector for low emission aircraft engines was conducted. Volume-of-fluids approach was used to track interface of fuel and air. Primary atomization of fuel stream was visualized, and thickness and mean velocity at the injector exit was calculated. Liquid fuel injected from fuel slots joined together as a thin film on preflimer surface, and interacted with swirling air. As instability on the fuel surface increased, separation of fuel as ligaments and droplets occured. The film thickness and velocity were used to as fuel injection boundary condition for reactive flow simulation. Primary reaction zone was formed in vicinity of the fuel nozzle, creating a stable flame inside the combustor.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.132-138
• /
• 1995

Rene80 superalloy was liquid phase diffusion bonded by using boron(B) as an insert material, where B has high diffusivity and higher melting point as an insert material. Bonding procedure and bonding mechanism of Rene80/B/Rene80 joint were investigated. As results, liquid metal was produced by solid state reaction between base metal and insert material on bonding zone. The liquid metal was produced preferentially at the grain boundary. Except for production of liquid metal, other bonding procedure was nearly same as TLP(Transient Liquid Phase) bonding. Bonding time, however, was reduced compared to prior result of TLP bonding. By bonding S.4ks at l453K, Ren80/B/Rene80 joint was isothermally solidified and homogenized where thickness of insert material was 7.5.mu.m.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.18 no.4
• /
• pp.758-770
• /
• 1996

Discectomy is the oldest and most commonly performed operation for the painful temporomandibular joint with internal derangement. It is the one operation for which there are longest follow-up study, with Eriksson, Silver, and Tolvanen et al reporting good results in patients about 30 years after discectomy. About 80% to 90% of patients clinically experience relief from pain and dysfunction after discectomy, and interestingly, the results may improve with time. However such as Myrhaug found headache and Poswillo supposed pain and limitation of movement as postoperative complications, even though this operation had the longest follow-up term, several aspects of discectomy remain unclear. The controversies to discectomy for TMJ with pain and dysfunction have laid emphasis only upon clinical results, and then the histomorphological study was planned to evaluate the morphologic change of TMJ after discectomy. To clarify the nature of the change through an observation on the morphologic changes of articular cartilage and subchondral bone of the condyle resulting from experimental unilateral discectomy in rabbit, the author excised the left articular discs of 12 male rabbits(control 4 rabbits), weighing about 3kg, and at 1, 3, 6, 9 weeks following surgery, harvested both(left surgical site and right nonsurgical sits) TMJ. The specimens were examined with light microscope after H-E and MT stain and the obtained results were as follows. 1. Histopathological features showed thickening of articular zone and active proliferation of fibrocartilaginous zone associated with slight proliferative zone in surgical site than control group. Also replacement of chondrocytes in calcified cartilaginous zone into bone cells was observed. 2. There were thinning of thickness of each zone of articular cartilage except calcified cartilagnous zone was observed in nonsurgical site. 3. In MT stain of condylar trabeculae, there was increased calcification in nonsurgical site than control and surgical site and the degree of calcification was similar in surgical site and control group. 4. In both site of experimental group no features of degenerative changes were observed. From the above results, it is presumed that the morphologic changes of surgical site discectomy are compensatory remodeling process characterized by an hyperplastic reaction of the articular zone and fibrocartilaginous zone filling the void created by removing the disc, and the bone changes are secondary to changes in the cartilage. Increased degree of calcification seen in condylar trabeculae of nonsurgical site results from the excessive use of condyle of that site.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.24-25
• /
• 2006

SmBCO coated conductors were successfully fabricated using EDDC (Evaporation using Drum in Dual Chambers) deposition system that is a bath type co-evaporation system for fabrication of superconducting tape and divided into two chambers named evaporation chamber and reaction chamber. To obtain long and high quality superconducting coated conductor, it is very important to secure the uniformity of all the deposition parameters m the deposition system such as deposition temperature, oxygen partial pressure, compositional ratios and so on. Therefore, we investigated the distribution of the parameters along the axis of the drum m EDDC on which tapes were wound helically. When the temperature on the middle point of deposition zone was $700^{\circ}C$, that on the edge of deposition zone was $675^{\circ}C$. When the thickness of SmBCO layer on the middle point of deposition zone was 1063 nm, that on the edge of deposition zone was 899 nm. The partial pressure of oxygen was 5 mTorr in the reaction chamber while that was $7{\times}10^{-5}$Torr in the evaporation chamber. The composition ratio of Sm:Ba:Cu, that was measured by EDX, was very uniform along the axis of the drum. Under these deposition conditions, critical current distribution along the drum axis was 175 A/cm, 190A/cm, 217.5 A/cm, 182.5 A/cm, 175 A/cm with the interval of 9 cm between samples. It means that the EDDC system has the potential of fabricating (100m, 200A) class coated conductor.