• Journal of Microbiology and Biotechnology
• /
• v.7 no.5
• /
• pp.345-351
• /
• 1997

An aqueous/organic two-phase reaction system was applied to the production of catechol using immobilized resting cells of Pseudomonas putida CY 400. Water/ethyl ether system was used because of high partition coefficient of catechol and thus to reduce the product inhibition and degradation. Among the tested immobilization carriers, polyacrylamide gel gave the highest catechol productivity. The immobilization seemed to protect the cells against solvent toxicity. From the simulation of reaction conditions based on two-phase models, it was found that there was an optimum acetate concentration at fixed benzoate and cell concentrations for the catechol productivity. A lower phase volume ratio (lower fraction of organic phase) gave a higher productivity. However, the substrate conversion was low at low phase volume ratio.

• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.128-135
• /
• 1997

Reaction diffusion and formation of $Ni_3Al$phase with $L1_2$ structure have been studied in temperature range of 1432K to 1573K using the diffusion couple of (Ni-40, 5at%Al)/(Ni-14, 1at%Al) and (Ni-49, 2at%Al)/ (Nickel). The layer growth of Ni$_{3}$Al pyhase in the annealed diffusion couple was measured by optical microscope and electron probe microanalyzer (EPMA). The layer growth of $Ni_3Al$phase in diffusion zone obeyed the parabolic law without any indication of grain boundary effects. The layer growth of $Ni_3Al$phase in temperature range of 1423K to 1573K was mainly controlled by the volume diffusion mechanism. The rate of layer growth of $Ni_3Al$phase was found to be colsely related to the composition of intermetallic compound NiAl phase. The activation energy for layer growth of $Ni_3Al$phase was calculated to be 127kJ/mol.

• Journal of Environmental Science International
• /
• v.8 no.2
• /
• pp.227-231
• /
• 1999

This study was conducted to investigate the removal characteristics of $PO_4^{3-}-P$ contained in livestock wastewater using waste concrete. With small particle size, increased dosage and temperature of water, $PO_4^{3-}-P$ was well removed by waste concrete.$PO_4^{3-}-P$ was removed by adsorption reaction in low pH of the primary phase, but the crystallization reaction predominated for increasing pH with passed time. As a result of adapting the adsorption isotherm equation, $PO_4^{3-}-P$ removal was more affected by the crystallization reaction than the adsorption reaction. In the SEM micrograph, there was no evident change on the waste concreter surface. Particle size was plate-phase before reaction but appeared a dense form to progress in the crystallization reaction.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.254-262
• /
• 1996

$Pb(Zr_{0.52}Ti_{0.48})O_{3}$ (PZT) ceramics were prepared with uniform particle size of $1~3\;\mu\textrm{m}$ by hydrothermal synthesis at various conditions, such as hydrothermal reaction temperature, concentration of mineralizer and reaction time. PZT ceramics were formed above $180^{\circ}C$ for 2 hrs reaction using 10 M KOH solution as a mineralizer, but reaction condition was slightly different by starting materials. Morphology and characterization of PZT powders were investigated by XRD and SEM. By increasing the reaction temperature, KOH concentration and reaction time, the composition of the PZT phase tended to be homogeneous phase.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.69-72
• /
• 2007

The objective of this work was to study the properties of purification of two liquid phase for exclusion of impurities in each phase. The experiments for process variables were carried out in the temperature range($H_{2}SO_{4}$ phase: $413{\sim}513$ K, $HI_{x}$ phase: $353{\sim}453$ K) and in the $N_{2}$ flow rate range($H_{2}SO_{4}$, $HI_{x}$ phase: $50{\sim}200$ mL/min). As the results, it is appeared that the principles of $H_{2}SO_{4}$ phase purification was due to stripping, evaporation and reverse bunsen reaction and $HI_{x}$ phase purification was due to stripping and reverse bunsen reaction. In purification of $H_{2}SO_{4}$ phase, the concentration rate of $H_{2}SO_{4}$ phase was controled by temperature but the temperature had few effects on yield of $H_{2}SO_{4}$. In purification of $HI_{x}$ phase, we observed products of side reactions($H_{2}S$, S) over 433 K. The purity of $HI_{x}$ phase was increased with increasing $N_{2}$ flow rate because impurites were decreased with increasing conversion of reverse reaction.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.287-292
• /
• 2002

Graft copolymerization of styrene and glycidyl methacrylate (GMA) to the peroxidized polypropylene (PP) fabric with E-beam in $O_2$ atmosphere was carried out in vapor phase with benzoyl peroxide (BPO) as an initiator. The degree of grafting of copolymers was increased with the increase of the reaction temperature and the highest degree of grafting was obtained at $70^{\circ}C$ with styrene, and at $80^{\circ}C$ with GMA. The highest degree of grafting of styrene grafted PP according to reaction time was higher than that of GMA grafted PP. In vapor phase graft polymerization, the degree of grafting of copolymers according to water composition in monomer mixture was effected by the boiling temperature of monomers.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3607-3617
• /
• 2012

In this paper, the study of various ortho- and meta-substituted Magnolol derivatives is presented. The reaction enthalpies related to three antioxidant action mechanisms HAT, SET-PT and SPLET for substituted Magnolols have been calculated using DFT/B3LYP method in gas-phase and water. Calculated results show that electron-withdrawing substituents increase the bond dissociation enthalpy (BDE), ionization potential (IP) and oxidation/reduction enthalpy (O/RE), while electron-donating ones cause a rise in the proton dissociation enthalpy (PDE) and proton affinity (PA). In ortho- position, substituents show larger effect on reaction enthalpies than in meta-position. In comparison to gas-phase, water attenuates the substituent effect on all reaction enthalpies. In gas-phase, BDEs are lower than PAs and IPs, i.e. HAT represents the thermodynamically preferred pathway. On the other hand, SPLET mechanism represents the thermodynamically favored process in water. Results show that calculated enthalpies can be successfully correlated with Hammett constants (${\sigma}_m$) of the substituted Magnolols. Furthermore, calculated IP and PA values for substituted Magnolols show linear dependence on the energy of the highest occupied molecular orbital ($E_{HOMO}$).

• 연구논문집
• /
• s.24
• /
• pp.63-79
• /
• 1994

This article reports a experimental study of the method to achieve a bond joint at lower temperature in a short time. DC magnetron sputtering of Sn, Sn/Pb, Sn/In and Sn/Cu on copper substrate was provided as an interlayer for Cu to Cu bonding under the air environment. Various examination was conducted and investigated on the effect of experimental parameters such as coating materials, coating time(or coating thickness), bonding temperature and bonding time etc. Bonding was performed at the temperature of $210^\circC-320^\circC$ for 0sec and interfacial reaction between the coated layer and copper substrate was examined using optical, scanning electron microscope and x-ray diffractometer. From the obtained results, it was found that intermetallic compounds layer consisted of $\eta-phase(Cu_6Sn_5)$ and $\beta-phase(Cu_3Sn)$ was formed at the joint interface for almost all coating materials. But the dominant phase formed in the preetched Cu substrate coated with Sn was $\beta-phase$. A characteristic morphology looks like a reaction ring, which was believed as the strong interconnecting regions between two substrates, was found to be formed on the reaction surface of copper substrates. The morphologies and compositions of the intermetallics, which depends on the regions of the reaction surface, was appeared as greatly different. Based on above results, the new bonding process to make the joint at lower temperature for short time can be admitted as a feasible process.

• Korean Journal of Materials Research
• /
• v.15 no.7
• /
• pp.473-479
• /
• 2005

Thermoelectric $Zn_4Sb_3$ alloys were synthesized by a conventional powder metallurgy process consisting of solid state reaction and hot pressing. Single phase $Zn_4Sb_3$ was successfully produced by the annealing of cold compact starting with the mixed elemental powders, and subsequent hot pressing yielded single phase bulk specimens without microcracks. Phase transformations in this alloy system during synthesis were investigated using XRD, SEM and EDS. Thermoelectric properties as a function of temperature were investigated from room temperature to 600 K and compared with results of analogue studies. Transport properties at room temperature were also evaluated. Thermoelectric properties of single phase $Zn_4Sb_3$ materials produced by this process are comparable to the published data. Synthesis by solid state reaction and hot pressing offers a potential processing route to produce a bulk $Zn_4Sb_3$.ٓ

• Journal of the Korean Ceramic Society
• /
• v.28 no.3
• /
• pp.205-214
• /
• 1991

Calcium carbonate fine powders were synthesized by blowing CO2 gas in CaO or Ca(OH)2 suspension, and the shapes of powders obtained were examined for each synthetic condition. When water was used as a solvent, ultrafine calcite powders with the average size of∼0.03$\mu\textrm{m}$ were obtained. When synthesized using methanol as a solvent, amorphous phase and spherical vaterite phase were obtained by suction filtering and non-filtering, respectively. Reaction did not occured in ethanol medium, but spherical vaterite phase was obtained by adding ethylene glycol in ethanol.