• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.225-231
• /
• 2003

In order to improve efficiency of a system with three-dimensional flow characteristics, this paper presents a new method that overcomes three-dimensional effects by using two-dimensional CFD and response surface method. The method was applied to shape optimization of cut-off in a multi-blade fan/scroll system. As the entrance conditions of two-dimensional CFD, the experimental values at the positions out of the inactive zone were used. In order to examine the validity of the two-dimensional CFD the distributions of velocity and pressure obtained by two-dimensional CFD were compared with those of three-dimensional CFD and experimental results. It was found that the distributions of velocity and pressure show qualitatively similarity. The results of two-dimensional CFD were used for constructing the objective function with design variables using response surface method. The optimal angle and radius of cut-off were determined as $72.4^{\circ}$ and 0.092 times the outer diameter of impeller, respectively. It is quantified the previous report that the optimal angle and radius of cut-off are approximately $72^{\circ}$ and 0.08 times the outer diameter of impeller, respectively.

• 방송공학회논문지
• /
• 제15권6호
• /
• pp.742-748
• /
• 2010

최근의 반복 검출 및 복호 (iterative detection and decoding : IDD) 기법에서의 연판정 방식에서는 log-likelihood ratio (LLR) 값의 신뢰도를 높이기 위해 기존의 구복호화 (sphere decoding) 방식보다는 리스트를 형성하는 구복호화방식 (list sphere decoding : LSD)이 대두되고 있다. 기존의 구복호화 방식과는 달리, 리스트 구복호화 방식은 그 성능의 우수함에도 불구하고 여러 격자 포인트들을 검출해야하므로 신호대잡음비 (signal-to-noise ratio : SNR)의 증가에 따른 복잡도의 이득을 거의 취할 수 없다. 또한 리스트 구복호화 기법은 리스트의 크기가 고정되어 있다는 점에서 비효율적이다. 본 논문에서는, 검출 과정에서 LLR에 큰 영향을 미치지 않는 격자 포인트들을 제거하는 기법을 소개한다. 이 과정은 구반경의 최적화를 바탕으로 이루어지며, 제안된 방식은 기존의 리스트 구복호화 기법과 비교하여 성능이 크게 떨어지지 않은 가운데 복잡도를 크게 감소시킨다.

• 한국유체기계학회 논문집
• /
• 제11권2호
• /
• pp.38-45
• /
• 2008

This study presents a numerical procedure to optimize the compressor design to increase the surge margin of compressor with response surface method (RSM). The Box-Behnken design method is used to reduce the number of calculation for fitting the second-order response surface. In order to consider the increase of surge margin during numerical optimization without any calculation at the surge point, the slope of compressor characteristic curve at the design point is suggested as an objective function in the present optimization problem. Mean line performance analysis method is used to get the design and off-design characteristic curves of centrifugal compressor. The impeller exit angle, impeller exit height and impeller radius are chosen as design variables. The optimum shapes show the increase of surge margin for the surge margin optimization and increase of efficiency for the efficiency optimization in comparison with an initial shape.

• 한국CDE학회논문집
• /
• 제10권2호
• /
• pp.114-120
• /
• 2005

This paper presents a novel method for radius measurement of fillet regions of polygonal models by using optimum onhogonal planes. The objective function for finding an optimum onhogonal plane is designed based on the orthogonality between the normal vectors of the faces in a filet region and the plane that is to be found. Direct search methods are employed to solve the defined optimization problem since no explicit derivatives of the object function can be calculated. Once an optimum orthogonal plane is obtained, the intersection between the onhogonal plane and the faces of interest is calculated, and necessary point data in the fillet region for measuring radii are extracted by some manipulation. Then, the radius of the fillet region in question is measured by least squares fitting of a circle to the extracted point data. The proposed radius measuring method could eliminate the burden of defining a plane for radius measurement, and automatically find a necessary optimum orthogonal plane. It has an advantage in that it can measure fillet radii without prior complicated segmentation of fillet regions and explicit information of neighboring surfaces. The proposed method is demonstrated trough some mea-surement examples.

• Structural Engineering and Mechanics
• /
• 제62권1호
• /
• pp.107-111
• /
• 2017

This paper deals with critical buckling load optimization of symmetric angle-ply laminated stepped flat columns under axial compression load. The design objective is the maximization of the critical buckling load and the design variable is the fiber orientations in the layers of the laminates. The classical laminate plate theory is used for the finite element solution of the laminated stepped flat columns. The modified feasible direction (MFD) method is used for the optimization routine. For this purpose, a program based on FORTRAN is exploited. Finally, the optimization results are presented for width ratios (b/B), ratios of fillet radius ($r_1/r_2$), aspect ratios (L/B) and boundary conditions. The results are presented in graphical and tabular forms and the results are compared.

• 한국유체기계학회 논문집
• /
• 제16권2호
• /
• pp.35-41
• /
• 2013

Inlet part of a printed circuit heat exchanger has been optimized by using three-dimensional Reynolds-Averaged Navier-Stokes analysis and surrogate modeling techniques. Kriging model has been used as the surrogate model. The objective function for the optimization has been defined as a linear combination of uniformity of mass flow rate and the pressure loss with a weighting factor. For the optimization, the angle of the inlet plenum wall, radius of curvature of the inlet plenum wall, and width of the inlet pipes have been selected as design variables. Twenty six design points are obtained by Latin Hypercube Sampling in design space. Through the optimization, considerable improvement in the objective function has been obtained in comparison with the reference design of PCHE.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.174-179
• /
• 2011

This paper focuses on the optimal step-over value for magnetic tool path. Since magnetic flux density is changed according to distance from center of magnetic tool. Enhanced surface roughness is also different according to change of radius. Therefore, to get a identical surface roughness on workpiece, it is necessary to find optimal tool path including step-over. In this study, response surface models for surface roughness according to change of radiuses were developed, and then optimal enhanced surface roughness for each radius was selected using genetic algorithm and simulated annealing to investigate relation between radius and surface roughness. As a result, it found that step-over value of 6.6mm is suitable for MAP of magnesium alloy.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.336-340
• /
• 1997

This paper is a study about motor technic of motion and feedforward control in order to shape cutting control on the machine tool. The shape error caused by delay of the servo system in the direction of radius at the time of circular cutting is reduced by feedforward control, shape error generated by the position command delay is minimized by using the acceleration/deceleration time constant after the interpolation. The study was verified to optimization of motion control on experiments of a vertical machining center of the machine tool.

• Journal of applied mathematics & informatics
• /
• 제24권1_2호
• /
• pp.367-376
• /
• 2007

In this paper we consider the global convergence of a new super memory gradient method for unconstrained optimization problems. New trust region radius is proposed to make the new method converge stably and averagely, and it will be suitable to solve large scale minimization problems. Some global convergence results are obtained under some mild conditions. Numerical results show that this new method is effective and stable in practical computation.

• 한국산업정보학회논문지
• /
• 제25권1호
• /
• pp.1-11
• /
• 2020

본 논문은 큰 스케일의 무선센서네트워크(Wireless Sensor Networks: WSN)에서 클러스터링을 위한 제어 메시지의 최적화된 전송반경을 사용하여 전체 네트워크의 수명을 증가시키는 방법을 제안한다. 또한 스케일이 큰 네트워크에서 노드들의 제어 메시지의 최대 전송반경과 에너지 소모에 대하여 고찰한다. 이를 위하여 일반 노드가 소모하는 에너지와 클러스터 헤드가 소모하는 에너지의 함수 형태로 제어 메시지 전송반경을 분석하고, 이를 바탕으로 최적의 전송반경을 구하는 방법을 제시한다. 제안한 방법을 이용하여 싱글 홉 및 멀티 홉 등의 여러 WSN 라우팅 환경에서 시행한 시뮬레이션 성능 분석 결과를 바탕으로, 본 논문에서 제안한 방법이 기존의 방법들에 비하여 전체 네트워크의 수명을 더욱 길게 운용하는 것을 보였다.