• 한국가스학회:학술대회논문집
• /
• 1997.09a
• /
• pp.45-52
• /
• 1997

The objective of this study is, with concept of fitness-for-purpose, to evaluate the fracture toughness in X-grooved weld HAZ(heat-affected zone) of QLT(quenching, lamellarizing and tempering)-processed $9\%$ Ni steel, qualitatively and quantitatively, and analyze the relation with the change of microstructure. In general, CTOD test is widely used to determine the fracture toughness of steel weldments. But several problem of accuracy has been brought up. Therefore, in this study, modified CTOD test was used for X-grooved weld HAZ for $9\%$ Ni steel. Additionally, microstructure of HAZ is observed and analyzed by OM, SEM and XRD. From the resulty, HAZ toughness of QLT-$9\%$ Ni steel decreased as the evaluated region approaches the fusion line. The decreased toughness was partly caused by reduction of the retained austenite content, resulted from decreased nucleation site of the retained austenite content, resulted from decreased nucleasion site for reverse transformation due to the increasing fraction of coarse grained region. On the other hand, unexpectedly, the increasing fraction of ductile weld did not increase the HAZ toughness. Therefore, in this X-grooved weld HAZ, the primary factor affecting fracture toughness was the fraction of coarse grained region, i.e., the weakest region.

• Journal of Korea Foundry Society
• /
• v.25 no.1
• /
• pp.23-29
• /
• 2005

Mechanical characteristics of Hi-Cr cast irons containing 16.8%Cr and 3.0%C were studied with various heat treatments. After as-cast Y-block ingots were annealed fully, the ingots were machined into cylinderical specimens with the size of 9mm in diameter and 20mm in length in order to investigate the effect of heat-treatments on mechanical characteristics of high Cr cast irons. All specimens were heat-treated by quenching- tempering, austempering and cyclic heat at the various temperatures(950, 1000, 1050 and $1100^{\circ}C$) respectively. The wear amount was measured for each heat-treated specimens against the counterpart of a hardened SKD11 steel at the following conditions; wearing velocity: 0.7 m/s, load: 100N and sliding distance: 70 km. After as-cast specimens were annealed, fine $M_{3}C$ carbides were formed, which affected the hardness and the wear resistance of Hi-Cr specimens. High hardness and good wear resistance were appeared on the specimens treated at 950 and $1000^{\circ}C$ and the austempered specimens show excellent wear resistance as well as high hardness.

• Journal of Korea Foundry Society
• /
• v.22 no.2
• /
• pp.69-74
• /
• 2002

The effects of heat treatments and alloying elements on the microstructure and mechanical charaterisitics of specially austempered ADIs containing alloying elements such as Cu, Mo and Ni were investigated. To compare with the effect of conventional and normal(CN) austempering treatment, two kinds of special austempering treatments which are those with pre-quenching and pre-heating were conducted. The hardness and uniaxial fatigue tests were carried out to evaluate the mechanical charateristics. The hardness of ADI treated by CN heat cycles was higher than those of other ADIs. Cu added ADI (Cu-ADI) tempered at 400 after austenitizing exhibited the highest fatigue life cycles. While austempering after prequenching makes the austenite with high carbon stable, which resulted in transformation to highly strengthened bainites from the carbon enriched austenite phases during tempering. The high carbon enriched banites is considered to improve the fatigue strength.

• Transactions of Materials Processing
• /
• v.31 no.2
• /
• pp.51-56
• /
• 2022

In this study, finite element analyses were performed by applying a stress ring and split die design to relieve the tensile stress acting on the die due to high surface pressure during warm-closed forging. The applied material was a yield-ratio-control-steel (YRCS). It was used without quenching or tempering after forging. In the case of stress rings design, the number of stress rings and the tolerance for shrink fit were different. Vertical and horizontal splits were applied for insert die split design. Case 5 die with three stress rings, 0.2 % shrink fit tolerance, and vertical split was selected as an effective die design for tensile stress reduction. Based on die stress reduction analyses, Case 5 die for warm-closed forging was produced and smooth forgeability was secured, making it possible to manufacture forging product of yoke with the required geometry. In addition, controlled cooling using warm forging heat was applied to secure mechanical properties of yokes. When oil cooling was used for direct controlled cooling after warm-closed forging, a relatively uniform Rockwell hardness distribution and high mechanical properties could be obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.555-559
• /
• 2011

Oil hydraulic piston pumps are extensively used worldwide because of their simple design, light weight, and cost effectiveness. However, an oil hydraulic pump is likely to have high leakage, friction, and low energy efficiency after long-term use. In oil hydraulic piston pumps the clearance between the valve block and the piston plays an important role in the volumetric and overall efficiency. We studied the wear property of the SACM645 material used in hydraulic piston pumps via experiments with different heat treatments. We prepared three different specimens. The maximum tensile strengths of the QT and QT-nitration specimens are similar (about 820 MPa), but the strains are significantly different. However, the fatigue characteristic depended on the heat treatment.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2014

Recently, the fuel oil of diesel engines of marine ships has been increasingly changed to heavy oil of low quality as the oil price is getting higher and higher. Therefore, the spiral gear attached at the motor of the oil purifier which plays an important role to purify the heavy oil is also easy to expose at severe environmental condition due to the purification of the heavy oil in higher temperature. Thus, the material of the spiral gear requires a better mechanical strength, wear and corrosion resistance. In this study, the heat treatment(tempering) with various holding time at temperature of $500^{\circ}C$ was carried out to the alloy of Cu-7Al-2.5Si as centrifugal casting, and the properties of both hardness and corrosion resistance with and without heat treatment were investigated with observation of the microstructure and with electrochemical methods, such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram, and a.c. impedance. in natural seawater solution. The ${\alpha}$, ${\beta}^{\prime}$ and ${\gamma}_2$ phases were observed in the material in spite of no heat treatment due to quenching effect of a spin mold. However, their phases, that is, ${\beta}^{\prime}$ and ${\gamma}_2$ phases decreased gradually with increasing the holding time at a constant temperature of $500^{\circ}C$. The hardness more or less decreased with heat treatment, however its corrosion resistance was improved with the heat treatment. Furthermore, the longer holding time, the better corrosion resistance. In addition, when the holding time was 48hrs, its corrosion current density showed the lowest value. The pattern of corroded surface was nearly similar to that of the pitting corrosion, and this morphology was greatly observed in the case of no heat treatment. It is considered that ${\gamma}_2$ phase at the grain boundary was corroded preferentially as an anode. However, the pattern of general corrosion exhibited increasingly due to decreasing the ${\gamma}_2$ phase with heat treatment. Consequently, it is suggested that the corrosion resistance of Cu-7Al-2.5Si alloy can be improved with the heat treatment as a holding time for 48 hrs at $500^{\circ}C$.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.3
• /
• pp.134-149
• /
• 2013

The Sudang-ri Site in Geumsan is considered the historic site where Baekje dominated the inland traffic route to Gaya through Geumsan and Jinan in the 5th Century. This study identified the production techniques of iron by conducting an analysis of metallographical microstructure of the artifacts such as an iron sword and an iron sickle that were excavated in Sudang-ri Site, Geumsan, one of the regions ruled by Baekje, and tried to figure out the characteristics and the technical systems of Baekje's ironmaking around the 5th Century by comparing them with other iron artifacts produced around the same time. The analysis showed that various production techniques were applied to the artifacts excavated in Sudang-ri Site, Geumsan. Depending on the production techniques, they can be divided largely into three methods: the simple shape-forging method, the steel manufacture method after forging, and the steel manufacture & heat-treatment method after forging. The iron sickle from the stone chamber tomb No. 1, which was produced only through forging, is mostly composed of soft ferrite at both edges of the blade and at the rear making the use of the weapon impractical. From this fact, it is presumed that they were produced as burial objects or ceremonial accessories for the person buried. The iron axe from the outer stone coffin tomb No. 1 and the iron swords and sickle from the outer stone coffin tomb No. 12, which were produced through the steel manufacture method after forging such as carburizing, did not go through the heat treatment such as quenching, but applied different production processes to each part. Therefore, it is deemed that they were produced as daily tools for cultivation rather than burial objects or ceremonial accessories. The production techniques following the forging process - carburizing and heat treatment - can be found on the iron swords from the outer stone coffin tomb No. 5 and the outer stone coffin tomb No. 12. The sturdy structure of the blade part and the durable structure of the rear processed with heat are deemed to have been produced as weaponry and used by the person buried. Based on the analysis of the iron artifacts excavated from Sudang-ri Site in Geumsan, the characteristics of iron production techniques were investigated by comparing them with the artifacts from Yongwon-ri Site in Cheonan, Bongseon-ri Site in Seocheon, and Bujang-ri Site in Seosan that were made around the same time as the cluster of Baekje tombs examined by the metallographical microstructure analysis of this study. For the iron artifacts analyzed here, the changes in the techniques were investigated using the iron swords common in all of the tombs. In the case of the iron swords, it was identified the heat treatment technique called tempering was applied from the 4th Century.