• Structural Engineering and Mechanics
• /
• 제10권5호
• /
• pp.505-516
• /
• 2000

This paper is a presentation of an experimental study about the elastic-partly plastic behavior of rectangular hollow steel pinned struts subjected to static cyclic axial loading and the evaluation of the compressive strength of retrofitted crooked struts. Retrofitting is achieved by welding stiffening plates along the webs of damaged struts. The material follows a quasi-kinematic hardening hysteresis path as observed from coupon tests. Test results are compared to those of an analytical model showing a good agreement for both standard and retrofitted struts. The comparison of different stiffener plate dimensions shows that more efficient strengthening is achieved by using long thin stiffeners rather than short thick ones.

• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.48-55
• /
• 1996

본 연구의 목적은 좌초시 선저부의 찢김 응답에 대한 치수 및 동적 효과를 고찰하는 것이다. 이를 위해 판 및 종방향 보강재를 가진 보강판에 대해 판두께를 변화시킨 찢김 시리즈 실험을 수행하였으며, 본 실험 결과뿐 아니라 타연구자에 의해 수행된 기존의 찢김 실험 결과를 바탕으로 판의 찢김 응답에 대한 판두께의 치수 효과를 분석하였다. 또한, 기존의 이론적 및 실험적 연구 성과를 바탕으로 판의 찢김 응답에 대한 동적 효과를 고찰하였다. 특히, 연강재뿐 아니라 고장력강재의 항복강도에 대한 변형속도 효과를 정량적으로 규명하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2059-2065
• /
• 2008

In this paper, quasi-static crushing tests of composite circular tubes under axial compression load are conducted to investigate the energy absorption characteristics. Circular tubes used for this experiment are glass/epoxy (GFRP) composite tubes, which is fabricated by the filament winding method. One edge of the composite tube is chamfered to reduce the initial peak load and to prevent catastrophic failure during crushing process. Two suggested trigger mechanisms for the composite tubes are investigated. Crushing modes are mainly affected by thickness/diameter ratio, and average crushing loads are mainly affected by their cross-sections. Energy absorption characteristics vary significantly as a function of the tube geometry, trigger mechanism, t/D ratio and the cross-sectional shape.

• Structural Engineering and Mechanics
• /
• 제5권2호
• /
• pp.177-191
• /
• 1997

In the paper, a fractional derivative Kelvin-Voigt model describing the dynamic behavior of a special class of fluid viscous dampers, is presented. First of all, in order to verify their mechanical properties, two devices were tested the former behaving as a pure damper (PD device), whereas the latter as an elastic-damping device (ED device). For both, quasi-static and dynamic tests were carried out under imposed displacement control. Secondarily, in order to describe their cyclical behavior, a model composed by an elastic and a damping element connected in parallel was defined. The elastic force was assumed as a linear function of the displacement whereas the damping one was expressed by a fractional derivative of the displacement. By setting an appropriate numerical algorithm, the model parameters (fractional derivative order, damping coefficient and elastic stiffness) were identified by experimental results. The estimated values allowed to outline the main parameter properties on which depend both the elastic as well as the damping behavior of the considered devices.

• 항공우주시스템공학회지
• /
• 제15권4호
• /
• pp.40-46
• /
• 2021

At launch, satellites are exposed to various types of structural loads, such as quasi-static loads, sinusoidal vibrations, acoustic/random vibrations, and shocks. The launch environment test is aimed at verifying the structural stability of the test object against the launch environment. Various types of launch environments are simulated by simple vibration, acoustic, and shock tests considering possible test conditions in ground. However, the difference between the launch environment and the test environment is one of the causes of excessive testing. To prevent overtesting, a notching technique that adjusts the frequency range and the input load considering the design load is applied. For notching, specific procedures are established considering the satellite development concept, selected launch vehicle, higher system requirements, and test target level. In this study, the notching method, established procedure, and development of a notching toolkit for efficient testing are described.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.191-194
• /
• 2007

In hot embossing lithography which has shown to be a good method to fabricate polymeric patterns for IT and bio components, it is very important to determine the proper process conditions of pressure, temperature, and time. It is also a key factor for predicting the optical properties of final product to calculate residual stress distribution after the embossing process. Therefore, to design the optimum process with right conditions, the ability to predict viscoelastic behavior of polymer during and after the hot embossing process is required. The objective of the present investigation is to establish simulation technique based on constitutive modeling of polymer with experiments. To analyze deformation behavior of viscoelastic polymer, the large strain material properties were obtained from quasi-static compression tests at different strain rates and temperatures and also stress relaxation tests were executed. With this viscoelastic material model, finite element simulation of hot embossing was executed and stress distribution is obtained. Proper process pressure is very important to predict the defect and incomplete filling.

• 한국해양공학회지
• /
• 제29권1호
• /
• pp.85-93
• /
• 2015

In this study, tensile tests were performed on aluminum alloys (AA6061 and AA6082) to investigate their mechanical behaviors at cryogenic temperatures. The temperature was varied from 110 K up to 293 K, and quasi-static strain rates of 10⁻⁴ s⁻¹ −10⁻² s⁻¹ were taken into account for the tests. The experimental results were analyzed to find the dependence on the temperature, strain rate, and fractured surfaces. As a result, it was found that the strength and elongation of the aluminum alloys were improved when the temperature was decreased. In addition, it was confirmed that the mechanical behaviors of the aluminum alloys were not dependant on the strain rate. Under a tensile load, two types of fractures were seen in the aluminum alloys: cup-cone (AA6061) and shear (AA6082).

• International Journal of Aeronautical and Space Sciences
• /
• 제15권1호
• /
• pp.102-111
• /
• 2014

An analytical model was developed to understand the physics and predict the functional performance of a pin puller. The formulated model is based on one-dimensional gas dynamics for an ideal gas. Resistive forces against pin shaft movement were measured in quasi-static mechanical tests, the results of which were incorporated into the model. The expansion chamber pressure and the pin shaft displacement were measured from an actual firing test and compared to the model prediction. The gas generation rate was adjusted by a correction factor, and the heat transfer rate was obtained through parametric analysis. The validity of the model is assessed for additional firing tests with different amounts of pyrotechnic charge. This model can provide knowledge on how the pin puller functions, and on which design parameters contribute the most to the actuation of the pin puller. Using this model, we estimate the functional safety factor by comparing the energy generated by the pyrotechnic charge to the energy required to accomplish the function.

• Computers and Concrete
• /
• 제26권3호
• /
• pp.227-237
• /
• 2020

Strain rate investigations are needed to calibrate strain-rate-dependent material models and numerical codes. An appropriate material model, which considers the rate effects, need to be used for proper numerical modeling. The plastic concrete cut-off wall is a special underground structure that acts as a barrier to stop or reduce the groundwater flow. These structures might be subjected to different dynamic loads, especially earthquake. Deformability of a structure subjected to dynamic loads is a principal issue which need to be undertaken during the design phase of these structures. The characterization of plastic concrete behavior under different strain rates is essential for proper designing of cut-off walls subjected to dynamic loads. The Cowper-Symonds model, as one of the most commonly applied material models, complies well with the behavior of a plastic concretes in low to moderate strain rates and will be useful in explicit dynamics simulations. This paper aims to present the results of an experimental study on mechanical responses of one of the most useful types of plastic concrete and Cowper-Symonds constant determination procedures in a wide range of strain rate from 0.0005 to 107 (1/s). For this purpose, SHPB, uniaxial, and triaxial compression tests were done on plastic concrete samples. Based on the results of quasi-static and dynamic tests, the dynamic increase factors (DIF) of this material in different strain rates and stress state conditions were determined for calibration of the Cowper - Symonds material models.

• 한국강구조학회 논문집
• /
• 제20권2호
• /
• pp.215-226
• /
• 2008

강관이 삽입된 강합성 중공 기둥의 내진 성능 평가 실험을 수행하였다. 준정적 실험을 통하여 강합성 중공 기둥과 일반 중실 RC기둥의 내진 성능을 비교 평가 하였다. 각각의 기둥 시험체에 대해 최대 하중과 변위의 관계를 측정하였으며, 이를 바탕으로 연성도, 소산에너지, 등가 감쇠비, 손상 지수가 계산되었다. 실험 결과 강합성 중공 기둥은 중실 RC 기둥에 비해 약 2배의 모멘트에 저항을 하였으며, 에너지의 흡수와 소산에서도 2배 정도의 성능을 보여주어, 강합성 중공 기둥의 우수한 성능을 확인하였다.