• 설비공학논문집
• /
• 제12권10호
• /
• pp.879-885
• /
• 2000

It is a serious subject for energy conservation to prevent the energy loss caused by mixing of heated and cooled air jets in a building which two types of air-conditioning systems are adopted in perimeter and interior zone. The purpose of this paper is to clarify the quantitative and qualitative mechanisms of the mixing loss and to propose preventive methods for it. In this paper, by using the dynamic heat load calculation method, heat extraction loads of a typical office building in Pusan are calculated. According to the results, numerical simulation based on the computational fluid dynamics were peformed in order to measure the mixing loss in physical size HVAC system. Then, the distributions of air temperature and velocity are analyzed in order to grasp the relations by setting temperature differences influence on the mixing loss.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제9권2호
• /
• pp.62-68
• /
• 2001

It is a serous subject for energy conservation to prevent the energy loss caused by the mixture of heated and cooled air jets in perimeter and interior zone of a building operated with tow kinds of air-conditioning system simultaneously. The purpose of this paper is to clarify the quantitative and qualitative mechanisms of mixing loss and to propose a evaluation method for it. By using the dynamic heat load calculation, heat extraction load of a typical office building in Busan are calculated. According to the results, numerical simulations based on CFD(Computational Fluid Dynamics) were performed in order to evaluate mixing loss in the physical size of HVAC system. Then, the distributions of air temperature and airflow patterns according to the differences of set-point temperature are analyzed to grasp relations how to influence mixing loss.

• 한국염색가공학회지
• /
• 제21권1호
• /
• pp.1-9
• /
• 2009

A lot of research has been made over the recent decade to develop testing packages with antimicrobial properties to improve food safety. In this study, a new method, experimental device and technology for environmental corresponding packages of polypropylene (PP) film has been developed to provide effective temperature buffering during the transport/long-term storage of grains or foodstuffs from the supplier to the market. This quantitatively optimized mixing system enabled to produce PP films with the 700$\sim$1,400d (width;1.5$\sim$3mm, thickness;0.01$\sim$0.5mm). In the whole mixing systems, the finely-granulated inorganic illite and PP virgin chip for master batch (M/B) chip was calculated by digital measurement methods, and then the M/B chip for PP film was adapted through a air jet and PP grinding method. The prepared PP film was characterized with tensile strength and elongation, far infrared radiation (FIR) emissivity, antimicrobial activity and deodorization properties. The results revealed that the two differently grain-sized illite could be show homogeneously dispersed on PP chip surface, and as the increasing of illite content, the FIR emissivity and the anion emission rate of film was increasingly improved. In both of 325 and 1,500 mesh-sized illite contained PP chip, of course the antimicrobial activity was good. But the ultimate deodorization rate for ammonia gas of PP film were found to be approximately the same.

• 한국농공학회논문집
• /
• 제65권1호
• /
• pp.61-72
• /
• 2023

The increase in the rearing intensity of pigs has caused deterioration in the pig house's internal environment such as temperature, humidity, ammonia gas, and so on. Traditionally, the widely used method to control the internal environment was through the manipulation of the ventilation system. However, the conventional ventilation system had a limitation to control the internal environment, prevent livestock disease, save energy, and reduce odor emission. To overcome this problem, the air-recirculated ventilation system was suggested. This system has a semi-closed loop ventilation type. For designing this system, it was essential to evaluate the ventilation rates considering the pressure loss of ducts. Therefore, in this study, pressure loss calculation and experiment were conducted for the quantitative ventilation design of a semi-closed loop system. The results of the experiment showed that the inlet through which external air flows should always be opened. In addition, it was also found that for the optimum design of the semi-closed loop ventilation system, it was appropriate to install a damper or a backflow prevention device rather than a ventilation fan.

• 동력기계공학회지
• /
• 제19권1호
• /
• pp.56-63
• /
• 2015

In this study, the exhaust characteristics of the diesel engine for the change of the mixing ratio of biodiesel fuel were quantitatively analyzed by using the numerical analysis method. As the fuel used in the experiment, the diesel and biodiesel(waste oil, soybean oil), the mixed fuel BD2(Diesel only), BD3, BD5, BD20, BD50 and BD100 were used. The injection pressure($p_{inj}$) was set to 400bar, 600bar, 800bar, 1000bar and 1200bar as the experimental variable. Also the concept of the standard deviation, Pearson's correlation coefficient and Spearman rank-order correlation coefficient based on the statistics was introduced in order to analyze the exhaust characteristics of the quantitative NOx and Soot according to the injection pressure and the mixing ratio variation of biodiesel blending fuel. It is considered that as a result of studies, for the waste oil, NOx and Soot can be simultaneously reduced through control of the mixing ratio at the regions of $p_{inj}=400bar$ and $p_{inj}=600bar$, and the Soot can be reduced without affecting on the emission of NOx at more than $p_{inj}=800bar$. For the soybean oil, NOx and Soot can be simultaneously reduced at $p_{inj}=400bar$ and the Soot can be reduced without affecting on the emission of NOx at $p_{inj}=600bar$.

• 한국진공학회지
• /
• 제6권S1호
• /
• pp.122-126
• /
• 1997

the Cu/polyimide system is known to be the best candidate for a multilevel interconnection system due to the low resistance of Cu and to the low dielectric constant of polyimide respectively. Ion beam mixing of Cu(40nm)/polyimide was carried out at room temperature with 80 keV Ar+ and N2+ form $1.5\times$1015 to 15$\times$1015 ions/cm2. The quantitative adhesion strength was measured by a standard scratch test. X-ray photoelectron spectroscopy and x-ray emission spectrocopy are employed to investigate the chemical bonds and the interlayer compound formation of the films Cu/Al/polyimide showed more adhesion strength than Cu/polyimide after ion beam mixing and N2+ ions are more effective in the adhesion enhancement than Ar+ with the same sample geometry. The XES results shows the formation of interlayer compound of CuAl2O4 which can reflect more adhesive Cu/Al/polyimide which has not been reported previously. The latter results is understood by the fact that N2+ ions produce more pyridinelike moiety, amide group and tertiary amine moiety whcih are known as adhesion promotors.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.523-529
• /
• 2018

Two liquids which are generally used as fuels of rockets are mixed and their mixing process is quantitatively investigated by the use of particle image velocimetry (PIV). As working fluids for the liquid mixing, Dimethylfuran (DMF) and JetA1 oils have been used. Since the specific gravity of DMF is larger than that of JetA1 oil, the DMF oil has been set at the lower part of the JetA1 oil. For better visualization of the mixing process, Rhodamin B powder has been blended into the DMF oil. An agitator having 3 blades has been used for mixing the two liquids. For quantitative visualization, a LCD monitor has been used as a light source. A color camera, camcoder, has been used for recording the mixing process. The images captured by the camcoder have been digitized into three color components, R, G, and B. The color intensities of R, G, and B have been used as the inputs of the neural network of which hidden layer has 20 neurons. Color-to-concentration calibration has been performed before commencing the main experiments. Once this calibration is completed, the temporal changes of the concentration of the DMF has been quantitatively analyzed by using the constructed measurement system.

• 정보보호학회논문지
• /
• 제19권6호
• /
• pp.175-184
• /
• 2009

정보 자산 보안 관련 위험을 추정함에 있어 정성적인 방법과 정량적인 방법이 사용되고 있으나, 두 가지 방법 나름대로 장단점을 갖고 있다. 지나치게 서술적이고 추상적인 정성적 방법과 구체적이지만 자료의 부족으로 인한 정확한 계산이 어려운 정량적 방법의 한계를 어느 정도 극복한 절충된 방법의 개발이 요구된다고 하겠다. 본 논문은 절충의 방법으로서 퍼지 숫자를 이용하는 방법을 제시하고 분석의 예를 보였다. 퍼지 숫자를 이용함으로 자료의 부족함을 전문자의 의견이나 가능한 자료로 대체할 수 있고 위험을 구체적인 수치로 추정할 수 있음을 확인하였다. 가상의 시스템에 대하여 다양한 위협을 가정하여 모의실험을 하였고 시스템에 대한 예상 위험과 비예상 위험을 예측하는 방법을 구현하였다.

• 청정기술
• /
• 제23권4호
• /
• pp.388-392
• /
• 2017

본 연구에서는 통기성 필름의 제조 공정에 대한 환경영향 특성을 분석하기 위해 전과정평가를 수행하였다. 특성화와 정규화 결과, 영향범주 별 환경영향은 지구온난화가 약 97%. 인간독성 2%의 기여도를 나타났다. 주요 기여도는 투입물인 고밀도 폴리에틸렌(HDPE)과 폴리프로필렌(PP) 그리고 에너지인 전력으로 나타났다. 세부 공정에서는 혼합단계(Mixing)가 57%, 부착단계(Lamination) 29% 압출단계(Extruder) 10% 순으로 높은 환경영향 기여도를 보였다. 환경 영향을 개선하기 위해서는 전력 사용량을 감소시키거나 원재료인 HDPE나 PP를 제외한 수율 향상을 고려한 새로운 공정 시스템 설계가 필요하다.

• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.157-167
• /
• 2003

The exciplex fluorescence technique with the TMPD (tetamethyl-Ρ-phenylene-diamine) / naphthalene dopant system was applied in a combustion-type constant-volume spray chamber. A detailed set of calibration experiments has been performed in order to quantify the TMPD fluorescence signal. It has been demonstrated that the TMPD fluorescence intensity was directly proportional to concentration, was independent of the chamber pressure, and was not sensitive to quenching by either water vapor or carbon dioxide. Using a dual heated-jet experiment, the temperature dependence of TMPD fluorescence up to 1000 K was measured. The temperature field in the spray images was determined using a simple mixing model, and an iterative solution method was used to determine the concentration and temperature field including the additional effects of the laser sheet extinction. The integrated fuel vapor concentration compared favorably with the measured amount of injected fuel when all of the liquid fuel had evaporated.