• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.675-681
• /
• 2016

A 41dB gain control range $6^{th}$-order band-pass receiver front-end (RFE) using CMOS switched frequency translated impedance (FTI) is presented in a 40 nm CMOS technology. The RFE consists of a frequency tunable RF band-pass filter (BPF), IQ gm cells, and IQ TIAs. The RF BPF has wide gain control range preserving constant filter Q and pass band flatness due to proposed pre-distortion scheme. Also, the RF filter using CMOS switches in FTI blocks shows low clock leakage to signal nodes, and results in low common mode noise and stable operation. The baseband IQ signals are generated by combining baseband Gm cells which receives 8-phase signal outputs down-converted at last stage of FTIs in the RF BPF. The measured results of the RFE show 36.4 dB gain and 6.3 dB NF at maximum gain mode. The pass-band IIP3 and out-band IIP3@20 MHz offset are -10 dBm and +12.6 dBm at maximum gain mode, and +14 dBm and +20.5 dBm at minimum gain mode, respectively. With a 1.2 V power supply, the current consumption of the overall RFE is 40 mA at 500 MHz carrier frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.628-631
• /
• 2003

In this paper, 2.4 GHz WLAN BPF(Band Pass Filter) using LTCC(Low temperature cofiring ceramic) multilayer technology was simulated and manufactured. A modified ${\lambda}/4$ Hair-pin resonator with shunt-to ground loaded capacitor is used to shorten resonator length and improve circuit Q factor. Proposed BPF has a combline structure. Electro-magnetic Coupling between coupled strip-line resonators is controlled to provide attenuation poles at finite frequencies. The overall size of the filter is $3.2{\times}1.6{\times}1.3mm^3$. The measured result shows good agreement with simulated data.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.166-176
• /
• 2007

Radio frequency (RF) microelectromechanical systems (MEMS) have been pursued for more than a decade as a solution of high-performance on-chip fixed, tunable and reconfigurable circuits. This paper reviews our research work on RF MEMS switches and switching circuits in the past five years. The research work first concentrates on the development of lateral DC-contact switches and capacitive shunt switches. Low insertion loss, high isolation and wide frequency band have been achieved for the two types of switches; then the switches have been integrated with transmission lines to achieve different switching circuits, such as single-pole-multi-throw (SPMT) switching circuits, tunable band-pass filter, tunable band-stop filter and reconfigurable filter circuits. Substrate transfer process and surface planarization process are used to fabricate the above mentioned devices and circuits. The advantages of these two fabrication processes provide great flexibility in developing different types of RF MEMS switches and circuits. The ultimate target is to produce more powerful and sophisticated wireless appliances operating in handsets, base stations, and satellites with low power consumption and cost.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.2
• /
• pp.148-154
• /
• 2009

In this paper, an embedded Kalman filter for a time-delayed controller is designed on an FPGA to estimate accelerations of the robot arm. When the time-delayed controller is used as a controller, the inertia estimation along with accelerations is needed to form the control law. Although the time-delayed controller is known to be robust to cancel out uncertainties in the nonlinear systems, performances are very much dependent upon estimating the acceleration term ${\ddot{q}}(t-{\lambda})$ along with inertia estimation ${\hat{D}}(t-{\lambda})$. Estimating accelerations using the finite difference method is quite simple, but the accuracy of estimation is poor specially when the robot moves slowly. To estimate accelerations more accurately, various filters such as the least square fit filter and the Kalman filter are introduced and implemented on an FPGA chip. Experimental studies of following the desired trajectory are conducted to show the performance of the controller. Performances of different filters are investigated experimentally and compared.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.73-82
• /
• 2005

This paper describes shock waveform synthesis methods for a shock response spectnlm over a short time interval with which intereference between parts within a test item is increased to perform a sufficient shock test for damage or malfunction which may be caused by the interference between parts, and a digital filter for obtaining a shock response history required for the shock waveform synthesis and a digital inverse filter for restoration by inversely using the digital filter. The time at which the maximax value occurs in the response history is detected in order to establish a delay time which is one of the parameters in the wavelet, on the condition that the natural frequency of SDOF system with a Q (quality factor) of 10 equals to the wavelet frequency of the zero delay wavelet input. A shock response spectrum over a short time interval and an abrupt change in the acceleration for an instant are illustrated as features of the synthesized waveform.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.281-287
• /
• 1998

$BiNbO_4$ ceramics doped with 0.07wt% $V_2O_5$ and 0.03wt% CuO (BNC3V7) were sucessfully sintered at $900^{\circ}C$ through the firing process with Ag electrode. The BNC3V7 shows typically Dielectric constant of 44.3, Thermal Coefficient of resonance Frequency(TCF) of 2 ppm/$^{\circ} and $Qxf_o$ value of 22,000 GHz. The laminated chip Low Pass Filter (LPF) is very sensitive to chip processing parameters, was confirmed by the computer simulation as a function of Q(Quality factors), filter size, capacitor layer thickness, inductor pattern widths. The multilayer type LPF was fabricated by screen-printing with Ag electrode after tape casting and then compared with the simulated characteristics. The results show that characterization of band pass width was similar to that of designed ones.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.658-665
• /
• 2011

In the present paper, a novel fast peak detector for single- or three-phase unsymmetrical voltage sags is proposed. The proposed detector is modified from a single-phase digital phase-locked loop based on a d-q transformation using an all-pass filter (APF). APF generates a virtual phase with $90^{\circ}$ phase delay. However, this virtual phase cannot reflect a sudden change of the grid voltage in the moment of voltage sag, which causes a peak value to be significantly distorted and to settle down slowly. Specifically, the settling time of the peak value is too long when voltage sag occurs around a zero crossing, such as phase $0^{\circ}$ and $180^{\circ}$. This paper describes the operating principle of the APF problem and proposes a modified all-pass filter (MAPF) to mitigate the inherent APF problem. In addition, a new fast peak detector using MAPF is proposed. The proposed detector is able to calculate a peak value within 0.5 ms, even when voltage sag occurs around zero crossing. The proposed fast peak detector is compared with the conventional detector using APF. Results show that the proposed detector has faster detection time in the whole phase range. Furthermore, the proposed fast peak detector can be effectively applied to unsymmetrical three-phase voltage sags. Simulation and experimental results verify the advantages of the proposed detector and MAPF.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.12
• /
• pp.2511-2520
• /
• 2011

This paper describes the parameter adjustment method of fuzzy membership function to improve the performance of multi-sensor fusion system using adaptive fuzzy-Kalman filter and cross-validation. The adaptive fuzzy-Kanlman filter has two input parameters, variation of accelerometer measurements and residual error of Kalman filter. The filter estimates system noise R and measurement noise Q, then changes the Kalman gain. To evaluate proposed adaptive fuzzy-Kalman filter, we make the two-axis AHRS(Attitude Heading Reference System) using fusion of an accelerometer and a gyro sensor. Then we verified its performance by comparing to NAV420CA-100 to be used in various fields of airborne, marine and land applications.

• Journal of Biosystems Engineering
• /
• v.33 no.5
• /
• pp.317-325
• /
• 2008

The electrocardiogram (ECG) measurement system consists of I/O interface to input the ECG signals from two electrodes, FPGA (Field programmable gate arrays) module to process the signal conditioning, and real time module to control the system. The algorithms based on wavelet transform were developed to remove the noise of the ECG signals and to determine the QRS-waves. Triangular wave tests were conducted to determine the optimal factors of the wavelet filter by analyzing the SNRs (signal to noise ratios) and RMSEs (root mean square errors). The hybrid rule, soft method, and symlets of order 5 were selected as thresholding rule, thresholding method, and mother wavelet, respectively. The developed wavelet filter showed good performance to remove the noise of the triangular waves with 10.98 dB of SNR and 0.140 mV of RMSE. The ECG signals from a total of 6 subjects were measured at different measuring postures such as lying, sitting, and standing. The durations of QRS-waves, the amplitudes of R-waves, the intervals of RR-waves were analyzed by using the finite impulse response (FIR) filter and the developed wavelet filter. The wavelet filter showed good performance to determine the features of QRS-waves, but the FIR filter had some problems to detect the peaks of Q and S waves. The measuring postures affected accuracy and precision of the ECG signals. The noises of the ECG signals were increased due to the movement of the subject during measurement. The results showed that the wavelet filter was a useful tool to remove the noise of the ECG signals and to determine the features of the QRS-waves.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.4
• /
• pp.59-65
• /
• 2008

This paper proposed a H.264 deblocking filter for the portable low-power multimedia. In H.264 deblocking filter, total 8 input pixels in filtering operations needs own filtering operation process respectively, and each filtering process has common structures for each filtering operation. By sharing common filter coefficients and registers, we have designed and implemented an smaller gated module, and moreover filtering operations are skipped on some or whole pixels what if we use some specific condition to operate filtering modules that need lots of operations. In the core of filtering modules, we achieve 33.31% and 10.85% gate count reduction compared with those of filtering modules of the conventional deblocking filter papers. The proposed low-power deblocking filter is implemented by using samsung 0.35um standard cell library technology, the maximum operationh frequency is 108MHz, and the maximum throughput is 33.03 frames/s with CCIR601 image format.