• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.102-112
• /
• 2012

The vast stores of biomass available in the worldwide have the potential to displace significant amounts of fuels that are currently derived from petroleum sources. Fast pyrolysis of biomass is one of possible paths by which we can convert biomass to higher value products. The wood pyrolysis oil (WPO), also known as the bio crude oil (BCO), have been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of BCO in a diesel engine requires modifications due to low energy density, high water contents, low acidity, and high viscosity of the BCO. One of the easiest way to adopt BCO to diesel engine without modifications is emulsification of BCO with diesel and bio diesel. In this study, a diesel engine operated with diesel, bio diesel (BD), BCO/diesel, BCO/bio diesel emulsions was experimentally investigated. Performance and gaseous & particle emission characteristics of a diesel engine fuelled by BCO emulsions were examined. Results showed that stable engine operation was possible with emulsions and engine output power was comparable to diesel and bio diesel operation. However, in case of BCO/diesel emulsion operation, THC & CO emissions were increased due to the increased ignition delay and poor spray atomization and NOx & Soot were decreased due to the water and oxygen in the fuel. Long term validation of adopting BCO in diesel engine is still needed because the oil is acid, with consequent problems of corrosion and clogging especially in the injection system.

• 한국환경보건학회지
• /
• 제13권1호
• /
• pp.17-33
• /
• 1987

As a result of technical advances and industrialization, the characteristics of domestic and industrial wastes are becoming more complex. Accordingly, improved treatment and disposal systems are being continuously sought to take account of complex characteristics and to comply with economic restrictions. In this study, an application of pyrolysis to the treatment of industrial wastes, including waste scrap rubber, waste raw material used in making the slipper bottom and waste PVC pipe, and the effectiveness of pyrolysis in resource recovery from these wastes were investigated. Batches of wastes were pyrolysed by external heating to a temperature of 400-800$\circ$C in a 32 mm diameter x 0.9 m long silica tube to produce combustible gases, oils and chars. Before the start of pyrolysis runs, the entire system was purged with nitrogen gas to exclude the air. The temperature inside the retort was controlled by the thermocouple in the gas stream, and referred to as the pyrolysis temperature. Under these conditions three products were separately collected and further analyzed. The results were summarized as follows. 1. More gases and less chars were produced with higher pyrolyzing temperature and with higher rates of heating, but the yields of oils tended downwards at temperatures above 700$\circ$C. Accordingly, operating conditions of pyrolysis should be varied with desired material. 2. Calorific values and sulfur contents of produced oils were sufficient and suitable for fuel use. Chars from waste rubber had high heating values with low sulfur contents, but calorific values of chars from waste PVC and waste slipper were as low as 3, 065-4, 273 kcal/kg and 942-2, 545 kcal/kg, respectively. Therefore, char from these wastes are inappropriate for fuel. 3. Soluble contents of Pb, Cd, Cu and Zn in chars from waste rubber and waste slipper were below the Specific Hazardous Waste Treatment Standards. However soluble contents of Pb and Cd in chars from waste PVC were one or two times and five or seven times exceedingly the Specific Hazardous Waste Treatment Standards, respectively. 4. Post high heating is desirable for treatment method of waste PVC which generates toxic hydrogen chloride. 5. The proportions of hydrogen, methane and ethane in produced gases were in the range of 3.99-35.61% V/V, 18.22-32.50% V/V and 5.17-5.87% V/V, respectively. 6. Pyrolysis is a useful disposal method in case of waste slipper, which was hardly combustible, and thus investigations of this kind of materials are required for effective management of industrial waste. 7. Based upon the possible market development for products, overall pyroly economics to take account of treatment values of noncombustible or hazardous materials should be evaluated.

• Korean Chemical Engineering Research
• /
• 제47권3호
• /
• pp.303-309
• /
• 2009

폐 농업용 비닐을 이용한 연료유 생산 공정을 위한 저밀도폴리에틸렌(LDPE)과 에틸렌비닐아세테이트(EVA) 수지에 대한 열분해 반응 실험을 하였다. 질소 분위기에서 상온에서 $650^{\circ}C$까지의 비등온 조건에서의 열분석기(열중량분석기, 시차주사열량계)와 $420^{\circ}C$의 배치형 반응기에서 무촉매 반응과 천연제올라이트, FCC 촉매, 폐 FCC 촉매, 중국 촉매(촉매 A) 등의 제올라이트계 촉매를 사용한 열분해가 행하여졌다. TGA 실험에서 무적제가 첨가된 EVA 수지는 열분해 개시 온도가 $250^{\circ}C$ 근처로 매우 낮아졌으나, 황토와 장수제 첨가는 열분해를 다소 지연시켰다. LDPE에서 제올라이트 계열 촉매는 촉매 A>폐 FCC 촉매>천연제올라이트>LDPE의 순으로 열분해 반응속도를 높이는데 유효하였다. EVA에서 제올라이트 계열 촉매 첨가 시는 폐 FCC 촉매>천연제올라이트>촉매 A>EVA 수지의 순으로 열분해 반응을 촉진시켰다. DSC 실험에서 제올라이트 계열 촉매 첨가 시 촉매 A>폐 FCC 촉매>천연제올라이트>LDPE의 순으로 융해개시 온도와 열분해열이 낮아졌다. 회분식 실험에서 천연제올라이트 첨가 시 시료 중 가장 높은 액상의 연료유 생성수율을 얻었다.

• 항공우주시스템공학회지
• /
• 제1권2호
• /
• pp.37-42
• /
• 2007

This paper proposes a numerical modeling approach to simulate the hybrid combustion phenomena. From the physical understandings of hybrid combustion, the computational domain was separated into three regions: the solid fuel, gas phase reactive flow, and the interface between solid and fluid. Moreover, for the accurate calculation, computational grids for these regions was generated at every time step considering the instantaneous moving interface which are governed by the balance equations using thermal pyrolysis. In the domain of reactive flow, by virtue of diffusion flame structure, turbulent combustion modeling was introduced using either mixture fraction approach or mean reaction rate approach.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.161-164
• /
• 2014

The feasibility of a molten metal as a bed material of a pyrolysis system was investigated. The molten metal has various advantages such as high thermal conductivity, wide operating range and low viscosity. Tin was selected since its physical characteristics are suitable for the purpose. As a results, it was found that pyrolytic oil yield and reaction rate were significantly enhanced with the molten Tin. In addition, oxygen component of the product oil was decreased due to Tin oxidation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.96-100
• /
• 2000

Recently ocean environmental pollution becomes very serious, so each governmental organization slove this problem. As part of the policy, KRISO has investigated distribution condition at ocean waste. Acc\ulcorner we found that combustble waste consists of ropes, fishing nets, and tires. These are, however, highly polyme\ulcorner existing incicerators have many problems to treat these. In this study we want to pyrolyze highly polymerized \ulcorner data for a design of fule production system without second pollution. Through the thermogravimetic experiment characteristics of pyrolysis and obtained some preliminary results.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제5C권5호
• /
• pp.217-220
• /
• 2005

We have fabricated a superconducting YBCO system according to the pyrolysis method and low pressure apparatus. In our experiment, the X-ray diffraction pattern of the non doped YBaCuO layer indicated that the superconductor contained only 90K phase crystal. The critical temperature and critical current density for a thick layer at $650^{\circ}C$ were Tc=90 K and $Jc=6{\times}10^{4}A/cm^2$ at 90K. In low pressure apparatus, the 90 K phase YBaCuO was grown at a lower temperature compared with the normal system. Tc and Jc at $650^{\circ}C$ were Tc = 90 K and $Jc=6{\times}10^{4}A/cm^2$ at 90K.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.668-669
• /
• 2006

The influence of $Eu^{3+}$ doping on the structural and morphological properties of the $Gd_2O_3:Eu^{3+}$ phosphor system, obtained ultrasonically via Spray Pyrolysis from common gadolinium and europium nitrate solutions, was studied. The particle morphology, crystalline and chemical structure were studied by XRD, SEM and EDS. TEM was applied in order to identify the structure and growth of "primary nanoparticles" and determine the presence of domains locally affected by "Moires Frames" and "Crystallite Size". The SADP allows determining the presence of a polycrystalline material with two phases in the "as-prepared" samples, and only an Ia3 phase along the thermal treatment.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2003년도 추계 학술발표회 논문집
• /
• pp.21-24
• /
• 2003

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2006년도 춘계학술대회 논문집
• /
• pp.197-200
• /
• 2006