• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.2
• /
• pp.89-96
• /
• 2000

This paper describes the forward type pulse power supply which is the simple circuit configuration and easy to be managed using a power semiconductor switching device(Power-MOSFET) in the view of commercialization. The maximum value of output pulse voltage of the proposed pulse power supply system can be realized by the variation of phase angle($\phi$) of bridge rectifier circuit and also its pulse period is determined by the duty ratio of Power-MOSFET. The principle of basic operating and the operating characteristics of the forward type pulse power supply are estimated by the switching frequency, the variation of phase angle($\phi$)It is shown that theoretical and experimental results are in good agreement by comparing simulation and experimental results of proposed pulse power supply when a lamp type ozonizer can be used as a load. This proposed pulse power system shows that it can be practically used in the future as a power source system in various fields.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.3A
• /
• pp.311-318
• /
• 2008

We propose new pulse shapes for FCC-compliant ultra-wideband (UWB) radios. The projections onto convex sets (POCS) technique is used to optimize temporal and spectral shapes of UWB pulses under the constraints of all of the desired UWB signal properties: efficient spectral utilization under the FCC spectral mask, time-limitedness, and good autocorrelation. Simulation results show that for all values of the pulse duration, the new pulse shapes not only meet the FCC spectral mask most efficiently, but also have nearly the same autocorrelation functions. It is also observed that our truncated (i.e., strictly time-limited) pulse shapes outperform the truncated Gaussian monocycle in the BER performance of binary TH-PPM systems for the same pulse durations. The POCS technique provides an effective method for designing UWB pulse shapes in terms of its inherent design flexibility and joint optimization capability.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.553-563
• /
• 2016

This paper presents a digital hardware implementation of a real-time simulator for a multiphase drive using a field-programmable gate array (FPGA) device. The simulator was developed with a modular and hierarchical design using very high-speed integrated circuit hardware description language (VHDL). Hence, this simulator is flexible and portable. A state-space representation model suitable for FPGA implementations was proposed for a dual three-phase induction machine (DTPIM). The simulator also models a two-level 12-pulse insulated-gate bipolar transistor (IGBT)-based voltage-source converter (VSC), a pulse-width modulation scheme, and a measurement system. Real-time simulation outputs (stator currents and rotor speed) were validated under steady-state and transient conditions using as reference an experimental test bench based on a DTPIM with 15 kW-rated power. The accuracy of the proposed digital hardware implementation was evaluated according to the simulation and experimental results. Finally, statistical performance parameters were provided to analyze the efficiency of the proposed DTPIM hardware implementation method.

• ETRI Journal
• /
• v.37 no.2
• /
• pp.241-250
• /
• 2015

In this paper, we present novel high-speed transmission schemes for high-speed ultra-high frequency (UHF) radio-frequency identification communication. For high-speed communication, tags communicate with a reader using a high-speed Miller (HS-Miller) encoding and multiple antennas, and a reader communicates with tags using extended pulse-interval encoding (E-PIE). E-PIE can provide up to a two-fold faster data rate than conventional pulse-interval encoding. Using HS-Miller encoding and orthogonal multiplexing techniques, tags can achieve a two- to three-fold faster data rate than Miller encoding without degrading the demodulation performance at a reader. To verify the proposed transmission scheme, the MATLAB/Simulink model for high-speed backscatter based on an HS-Miller modulated subcarrier has been designed and simulated. The simulation results show that the proposed transmission scheme can achieve more than a 3 dB higher BER performance in comparison to a Miller modulated subcarrier.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.226-228
• /
• 2006

This paper presents the two lossless auxiliary inducors-assisted voltage source type half bridge(single ended push pull:SEPP) series resonant high frequency inverter for induction heated fixing roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation forwide its output power regulation ranges and load variations under constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operatprinciple is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation charactertics-based on the high frequency PDM strategy. The experimenoperating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimenones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliimplemented here is proved from the practical point of view.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.683-686
• /
• 2001

This paper presents a novel prototype of the utility­interactive voltage source type sinewave pulse modulated power inverter using a high-frequency flyback transformer link. The proposed power conditioner circuit for the solar photovoltaic generation and small scale fuel cell has an isolation function due to the safety of the power processing system, which is more cost effective and acceptable for the small-scale distributed renewal energy conditioning and processing systems. The discontinuous current mode(DCM) of this power processing conversion circuit is applied to implement a simple circuit topology and pulse modulated control scheme. Its operation principle is described on the basis of simulation evaluations and theoretical considerations. The simulation results obtained herein prove that the proposed inverter outputs with sinusoidal waveforms and unity power factor currents are synchronized to the main voltage in utility power source grid. In this paper, the soft switching topology of high­frequency linked sinewave pulse modulation inverter is proposed and discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.226-232
• /
• 2000

This paper develops a finite element model for studying the crashworthiness analysis of a mid-size truck. A simulation for a truck frontal crash to a rigid barrier using the model is performed with PAM-CRASH installed in super computer SP2. Full vehicle model is composed of 86467 shell elements, 165 beam elements and 98 bar elements, and 86769 nodes. The model uses four material model such as elastic, elastic-plastic(steel), rigid and elastic-plastic(rubber) material model which are in PAM-CRASH. Frame and suspension system are modeled with 28774 shell elements and 31412 nodes. Cab is modeled with 34680 shell elements and 57 beam elements, and 36254 nodes. Bumper is modeled with 2262 shell elements, and 2508 nodes. Axle, steering shaft, etc are modeled using beam or bar elements. Mounting parts are modeled using rigid bodies. Bodies are interconnected using nodal constrains or joint options. To verify the developed model, frontal crash test with 30mph velocity to a rigid barrier is carried out. In the crash test, vehicle pulse at lower part of b-pillar is measured, and deformed shapes of frame and driver seat area are photographed. Those measured vehicle pulse and photographed pictures are compared those from the simulation to verify the developed finite element model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.885-890
• /
• 2015

LLC resonant converter has been widely used because of its high efficiency and high energy density. In this paper, we designed a LLC resonant converter as the main power supply of the Nd:YAG pulse laser. First harmonic approximation (FHA) is used to model the LLC resonant converter. FHA equivalent circuit model and the transfer function of the LLC resonant converter is proposed. Soft start technology is also used to suppress the surge current. The laser output simulation test result is identical with the practical test, the laser energy of every pulse can reach up to 2.5J, and the pulse per second (PPS) can be adjusted from 6 to 18. The power system is verified stable and reliable by both of the simulation and experiment results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.12A
• /
• pp.1189-1197
• /
• 2006

Ultra-wideband(UWB) is a killer technology for short-range wireless communications. In the past, most of the UWB research focused on physical layer but the unique characteristics of UWB make it different to design the upper layer protocols than conventional narrow band systems. Cross-layer protocols have received high attention for UWB networks. In this paper, we investigate the performance of two physical layer schemes: Time Hopping Binary Pulse Position Modulation(TH-BPPM) and Time Hopping Binary Pulse Amplitude Modulation (TH-BPAM) with proposed private MAC protocol for UWB ad-hoc networks. From pulse level to packet level simulation is done in network simulator ns-2 with realistic network environments for varying traffic load, mobility and network density. Our simulation result shows TH-BPAM outperforms TH-BPPM in high traffic load, mobility and dense network cases but in a low traffic load case identical performance is achieved.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.265-270
• /
• 2000

We investigate the effects of the power and wavelength of externally injection seeded light on timing jitter and pulse width in a gain-switched $1.55\mu\textrm{m}$ DFB semiconductor laser by numerical simulation based on the transmission line laser model. As external seeding power increases, the timing jitter decreases and the pulse width increases. The lowest timing jitter is observed when the seed wavelength is aligned with the chirped spectrum center. By external seeding, we can decrease the timing jitter up to 1/2.7 without noticeable increase in pulse width. Our simulation results reasonably well agree with our sampled experiment and the other published papers. This proves the validity of our model to analyze a system based on a semiconductor laser. laser.