In recent years, it had focused on the improvement of paper properties by addition of NFC (Nano-fibrillated Cellulose). Although the addition of NFC to wet-end of papermaking process could be suggested as a new solution to improve the strength properties of paper, it was not possible to avoid the bad drainage caused by the added NFC's chocking pores of wet web. Instead of the direct addition to wet-end, spraying of NFC to web in wire-section was tried in this study and evaluated by checking various paper properties including surface smoothness, tensile strength, folding endurance and stiffness. According to the increase of spraying amount of NFC, above mentioned paper properties were enhanced without excessive deterioration of drainage. Compared with direct introduction to wet-end, spraying could be regarded as a more proper method to enhance the surface smoothness and strength properties of paper.
The first step to utilize the growing resources of Italian poplar (Populus euramericana I-476) for pulp-Woods, its characteristics and adaptabilities to the pulp industry must be investigated completely. The plantation methods are important for its fast growing in stock, and no less important is the cutting age for its utilization as pulpwood. In this paper, the stone groundwood pulping, refiner groundwood pulping and chemi-groundwood pulping characteristics by the age of tree, along with their physical and chemical characterstics were tested, and relationships between the age groups were analyzed to find out the optimum felling age. The results obtained are as follows: 1. The coefficient of pliability was a little higher in the case of younger trees. 2. The water retention value of each pulp was directly proportional to its physical strength, but this tendency was not detected between the age groups of sample woods. 3. Generally, the physical strength of younger wood pulp was lower regardless of the pulping process. But in the case of pretreatment with NaOH, Asphund and CGP pulp from 5 year old sample wood were stronger in physical strengths than those of GP and Asplund pulp with no pretreatment from 10 years old sample wood. 4. The tear factor of Asplund pulp with alkali pretreatment was higher than that of CGP pulp but the breaking length and the burst factor was similar in all processes. Considering the pulp yield and its brightness, CGP process seems to be advantageous. 5. The dissimilarity of physical strength between 7 and 10 years old wood pulp was not very large in all pulping processes but the physical strength of 5 year old wood pulp was very weak. In the of groundwood pulping from Italian poplar woods, 5 year old wood pulp should be mixed with other long fiber pulp for making a good paper.
As the demands of environment protection increase, the pulp mold container is developed to substitute for the plastic cushion materials like EPS(expanded poly styrene). The water-absorbing ratio, tensile strength and compressive strength of pulp mold are important factors to evaluate its shock absorbing characteristics. The study was performed to investigate the effects of the mechanical property changes on the various conditions of temperature and relative humidity for pulp mold containers made of mixed materials on ONP(old newspaper) and OCC(old corrugated container). This study also is evaluated the optimized mixing ratio of materials for making pulp mold by analyzing the changes of physical properties according to a various procured temperature and relative humidity conditions. The results show that the water absorption ratio of sample increased significantly, and tensile strength decreased $20{\sim}30%$, compressive strength decreased $10{\sim}20%$ by increasing relative humidity condition. And the results show that the ONP 50% and OCC 50% was optimized mixing ratio according to the samples.
This research has been examined to measure the degree of the fiber damage of ozonenation high yield pulp in the beating process. Ozone treated the TMP(Thermomechanical Pulp) and CTMP(Chemithermomechanical Pulp) of spruce and the CTMP of birch has been beaten to be reached 200ml(freeness) of its content. It had been studied the forming of fiber distribution by treatment for long fiber, short fiber, fine with the above method. As ozone treatment time gets longer, the pulp has showed the tendency of increasing the fiber content of 28, 48mesh. Ozone treated fiber has been increased long fiber content by being added softness. By given longer ozone treatment time, the TMP and CTMP of spruce has showed the decreasing of fiber content. On the contrary, CTMP of birch has showed the increasing its fiber content. It had proved that the results of difference are rather closer to the species of tree than closer to the kinds of pulp. The fiber content of over 200mesh which has created in beating process demonstrates the decreasing of its fiber content by getting longer ozone treatment time. The softness of fiber can be extracted by the lignin of fiber surface that had been formed by ozone treatment. Thus we assume that the fiber in the process of beating obtains less physical damage.
To use the African tulip tree (Spathodea campanulata) as raw material for chemical pulping, soda and soda-AQ pulping was investigated. In chemical compositional analysis, lignin contents of African tulip (33.1%) was higher than other hardwood such as Yellow poplar (17.5%), Acacia (27.1%), or Eucalyptus (24.2%). Soda or soda-AQ pulping with African tulip tree resulted in yield at 43.4-44.8% with 29.5-34.5 Kappa number, pulping condition with 20-22% active alkali. Kappa number of African tulip tree pulp was quite higher than other tropical hardwood (Eucalyptus or Accacia) with less yield due to higher lignin content in wood. Fiber length and width of pulp from African tulip tree was similar to Accacia pulp and shorter than eucalyptus pulp.
Styrofoam as shock-absorbing materials for packaging has been regarded as one of non-biodegradable products leading to soil contamination at a landfill and release of dioxine during its incineration. For avoiding severe burdens on our environments by styrofoam, it must be replaced by environment-friendly materials. In order to evaluate availability of pulp fibers as a substitute for styrofoam, various extrusion processes were applied for making optimal biodegradable products. Then thermomechanical pulp fibers made of Pinus radiata and Pinus rigida were uniformly mixed with other additives such as starch and polyvinyl alcohol prior to expansion. The physical properties of the final products were examined by measuring expansion efficiency, compression strength, and elastic modulus. Wheat starch played a key role to maintain optimal flowing conditions within the barrel of the extruder irrespective of addition of soluble starch and polyvinyl alcohol. However, as the amounts of wheat starch in raw-materials increased, the elastic modulus of the expanded materials greatly increased. High elastic modulus is not suitable as shock-absorbing products for packaging. Thus the wheat starch must be added at a minimum if possible, that is, below 20% based on oven-dried weight of pulp fibers. the elastic modulus of the expanded products was decreased as their moisture contents increased. For the products containing 20% wheat starch, the lowest elastic modulus, 844.64 kPa was obtained under 10% of the moisture content. This was similar to that of styrofoam.
Environment-friendly shock-absorbing materials were made of wastepaper such as Korean old corrugated containers(KOCC) and Korean old newsprint (KONP) with a vacuum forming method. The plate-like cushioning materials made of KOCC and KONP respectively by vacuum forming showed superior shock-absorbing properties with lower elastic moduli compared to expanded polystyrene (EPS) and pulp mold. Even though the plate-like materials had many free voids in their fiber structure, their apparent densities (${\approx}0.1g/cm^3$) were a little higher than that of EPS (${\approx}0.03g/cm^3$) and much lower than that of pulp mold(${\approx}0.3g/cm^3$). However, the elastic moduli of the cushioning materials made of wastepaper were much lower than that of EPS or pulp mold. This finding implies that the cushioning materials made of KOCC fibers containing more lignin than KONP show better shock-absorbing properties than KONP. Moreover, the cushioning materials made of KOCC and KONP respectively showed greater porosity than pulp mold. The addition of cationic starch to the cushioning materials contributed to the increase in the elastic modulus to the same level as that of EPS. Furthermore, the deterioration in fiber quality by repeated use of wastepaper played a positive role in improving shock-absorbing ability.
White Jabon (Anthocephalus cadamba Miq.) is one of the fast growing species in Indonesia and has the potential as the raw material for pulp and paper. In this research, 3, 5, and 7 years old White Jabon woods were pulped under different active alkali charge of 15%, 18%, 21%, 24%, and 27%, and its effect on delignification degree, kappa number, pulp yield, pulp viscosity, brightness, unbeaten freeness, and delignification selectivity was investigated. The results showed that tree age and active alkali concentration influenced the quality of pulp and pulping properties, except for that of unbeaten freeness. Delignification degree increased with increasing active alkali charge, and this brought about the decrease of pulp kappa number. The pulping yield tended to decrease below the Klason lignin of approximately 4%. Even though the 3 years old wood resulted in the highest brightness and highest delignification selectivity, the highest pulp viscosity was obtained with the 5 years old wood. The dominant fiber length of all wood ages was in the range of 1.2 - 2.0 mm. The 3 years old wood was considered to be the most promising raw material for kraft pulping in the view point of pulping properties, pulp quality and harvesting rotation.
To use bamboo in the pulp industry, the anatomical characteristics of 60-day-old, 1-year-old, 2-year-old, and 3-year-old moso bamboo (Phyllostachys pubescens Mazel), and the characteristics of fiber and sheet of alkali pulp made of moso bamboo were investigated. Moso bamboo is composed of metaxylens and parenchyma cells in the inner part of the wall, and thick-walled small bundle sheathes near the outer walls. Moso bamboo showed the heterogeneity in anatomical structure. The longest fibers were shown in the middle part, and the widest width in the inner part. The lignin contents were 14.4% in 60-day-old bamboo, which was not lignified yet. The lignin contents in bamboo above 1 year were approximately 35%. The yields of alkali pulp of moso bamboo were in the range between 41 and 47%, and the yields tend to decrease with the increase of ages. The lignin contents of 60-day-old bamboo were 2.1% and those of bamboo above 1 year showed approximately 4% to 5% increment. The length, width, and curl index of fiber in alkali pulp appeared to be similar in all ages. However, coarseness increased slightly with the increase of bamboo ages. The distribution of long fiber was shown much in 60-year-old bamboo. The optical and mechanical properties of moso bamboo tended to decrease with the increase of bamboo age.
The study aimed to evaluate the probiotic properties, antioxidant activity and fermentative capacity of Acremonium charticola and Rhizopus oryzae isolated from the Indonesian fermented dried cassava, with particular application on poultry. A. charticola inhibited the growth of Escherichia coli and Aspergillus flavus. A. charticola and R. oryzae grew in potato dextrose agar (PDA) adjusted to pH 3 and 8 or in PDA supplemented with bile salt up to 0.8%. After soaking for 8 hr, the survival rate of A. charticola in the simulated gastric juice (pH 2) and bile solutions (2% bile salt) was lower than that of R. oryzae. A. charticola and R. oryzae exhibited strong antioxidant activities. Compared to unfermented cassava pulp (control), the fibre content of cassava pulp tended to be lower after fermentation with A. charticola for 14 days. The populations of A. charticola and R. oryzae were significantly higher in fermented cassava pulp than in unfermented one. Coliform was higher in cassava pulp fermented with R. oryzae or A. charticola + R. oryzae compared to control after 7 days of fermentation, however, the bacteria were not different between A. charticola-fermented cassava pulp and control. Lactic acid bacteria (LAB) were higher in A. charticola- and R. oryzae-fermented cassava pulp than those in control, however, no difference of LAB was observed between A. charticola + R. oryzae-fermented cassava pulp and control. In conclusion, A. charticola exhibited antibacterial, antifungal and antioxidant activity, gastrointestinal persistence and fermentative capacity that may be beneficial for poultry industry.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.