• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.2
• /
• pp.42-49
• /
• 1999

Although many researches have been made on the adsorption of cationic starches onto chemical pulp fibers, only limited studies have been reported for deinked pulp(DIP) and thermomechanical pulpI(TMP). In this experiment, the adsorption behavior of the cationic starches onto DIP and TMP fibers investigated. Almost complete adsorption of cationic starches onto the pulp fibers were observed when the addition rate of starch was low. Adsorption ratio decreased abruptly when 3.5% and 4.0% of cationic starches were adsorbed onto deinked pulp and thermomechanical pulp, respectively. Adsorption of cationic starches increased as the degree of substitution decreased and as the pH of the pulp slurry increased. TMP fibers adsorbed more cationic starches than DIP because of its greater charge density, and this led to greater improvement in strength properties for the TMP sheets.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.239-244
• /
• 1999

aluminum sulfate (alum) as a representative retention aid in papermaking processes was added to pulp suspensions, and the aluminum components adsorbed on the pulp were investigated quantitatively by two types of X-ray elementary analyses with regard to simultaneous changes of their surface charges. X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence analysis (XFA) were applied to determine the aluminum components retained in pulp pads up to ca. 10 nm and 100${\mu}$m depth, respectively. In other words, XPS was utilized to analyze the outermost surface layers of the samples, and XFA was available for measurement of their extensive regions. A particle charge detector (PCD) was used to monitor streaming potentials at various pHs of the pulp mixtures under moderate sharing conditions. At pH 4.5 of pulp suspensions containing alum, surface charges of pulp fibers varied from negative to slight negative (approximately neutral) according to adsorption of aluminum components onto the pulp fibers. Subsequently, when a dilute NaOH solution in limited amounts was added to pulp mixtures, both streaming potentials and surface aluminum content of the pulp fibers increased distinctly although little total aluminum retention increased. Further addition of alkali solutions brought drastic decreases of the surface charges and surface aluminum content, while total aluminum content, on the contrary, increased gradually under neutral conditions. These results indicate that residual aluminum ions remained in pulp suspensions are predominantly adsorbed on surfaces of pulp fibers by adequate alkali additions and they must sufficiently cationize the fiber surfaces with increases of somewhat cationic aluminum complexes formed on the surfaces. On the other hand, aluminum components formed in higher pH ranges have nearly no contribution to improvement of charge properties of the pulp fiber surfaces, even though aluminum retention in pulp pads increases. XPS and XFA analyses combined with streaming potential measurement using a PCD suggest close relationships between aluminum content on the pulp fiber surfaces and their charge properties.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.51-59
• /
• 2006

The surface of various mechanical pulp fibres including thermomechanical pulp (TMP), chemithermomechanical pulp (CTMP), and alkaline peroxide mechanical pulp (APMP) fibres, were characterized using SEM, AFM, and XPS. With SEM and AFM, middle lamella material was observed to be non-fibrillar, patch-like, while fibre secondary wall was observed to have a microfibrillar structure. It was found that after the first-stage refiner, lignin-rich middle lamella remainders are present on the fibre surface of all three pulps, although most of the fibre surfaces expose microfibrillar structure. After the final-stage refining, large amounts of granules are present on the TMP fibre surface. In contrast, most middle lamella remainders remain on the surface of CTMP fibres after final stage refining and even after peroxide bleaching. XPS results have confirmed that the non-fibrillar surface material is the lignin-rich middle lamella remainder., and the remainders of middle lamella contribute to the high surface lignin concentration.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.23-32
• /
• 2015

In this study, chemical and physical changes of dissolving pulps which have similar viscosity by dry milling and fractionation were investigated. We used two types of dissolving pulp made from wood and cotton linter fiber, respectively. Dry milling was executed by knife cutter and pulp powders were fractionated by sieve shaker into 4 grades. We analyzed fiber properties, crystallinity index, viscosity, molecular weight of pulp sheet and powders. It was found that poly-dispersity index of cotton linter pulp was smaller than that of wood pulp, meaning that cotton pulp has more narrow molecular weight distribution. It was assumed that these were related to exposure times to chemical treatment which cut cellulose chains not evenly. At least 4 times of chemical treatments for wood pulp were executed and only two times of chemical treatments for cotton linter pulp were done. After dry milling average molecular weight and crystallinity index of cotton linter pulp powders were reduced and these were related to fines content and shape of pulp powders.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.2
• /
• pp.31-39
• /
• 2011

The applicability of arrowroots as materials for paper manufacture was investigated by evaluating the characteristics of arrowroots pulping and pulps, and the surface characteristics of paper made of arrowroots. The results is as follows. The yield of grounded pulp, alkaline pulp, grounded bleach pulp, and alkaline bleach pulp are 98.0%, 37.7%, 84.8%, and 32.5%, respectively. The extraction components in arrowroot's fibers was shown high in 1%-NaOH extraction. The amount of holocellulose and lignin were largely decreased, but a slight decrease was shown in the bleaching processes. Many shivers were shown in the grounded fibers. The amount of shivers was decreased and the single fibers were increased during the process of bleaching. The alkaline pulp and the alkaline bleach pulp showed high in the beating time and freeness than the grounded pulp and grounded bleach pulp. The conditions of sheet surface according to beating time is effected largely by the conditions of original pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.3
• /
• pp.15-22
• /
• 2008

Properties of pulp fibers can be modified by LbL multilayering technology. We evaluated the effect of stock composition on the polyelectrolyte multilayering performance of pulp fibers in this study. Stock composition was varied with pulp type and fines content. Three types of pulp-Hw-BKP, BCTMP and KOCC-were treated with polyelectrolytes of poly-DADMAC and PSS. Fines content of stock were controlled at 0, 10, 20, 30, and 40%. Zeta potential of pulp fibers and charge demand of filtrate were evaluated. The highest adsorption ratio was obtained for BCTMP because of its shortest fiber length and highest specific surface area. Higher fines content in the stock increased the adsorption ratio of polyelectrolyte onto pulp fiber and it required a higher amount of polyelectrolyte for charge neutralization. For the pulp stock with higher fines content, a higher level of polyelectrolyte and the increased layer number were required to modify and stabilize the electrochemical properties of pulp fibers.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.10a
• /
• pp.133-141
• /
• 2011

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.13-20
• /
• 2015

Soda-AQ pulp made from sugarcane bagasse (SCB) and oil palm trunk (OPT) were bleached in element chlorine free (ECF) sequence. Bleached SCB and OPT pulp was achieve higher brightness than 85.0% ISO. Viscosity of SCB bleached pulp and OPT bleached pulp were achieved 18-27 cPs and 18-26 cPs. In 7.8% active chlorine dioxide addition, bleached SCB pulp was shown 88.7% ISO brightness and 20.4 cPs viscosity. And bleached OPT pulp was shown 88.5% ISO brightness and 18.8 cPs viscosity with 7.8% active chlorine dioxide addition.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.11-20
• /
• 2014

The objective of this study was to investigate the beating properties of two types of cotton pulps such as "cotton lint mixed pulp" and "cotton linter pulp". In order to improve refining characteristics, the effects of carboxymethyl-cellulose (CMC) pre-treatment, mixing ratio changes of cotton lint mixed pulp and cotton linter pulp, and refining load changes were analyzed. In mill application, it was possible to improve the refining characteristics and maintained the strength properties of the paper by applying increasing ratio of cotton linter pulp mixing and controlling the refining methods.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.3
• /
• pp.83-90
• /
• 2004

Pulp mold is one of the famous environmental friendly materials, which made from re cycled materials such as old newsprints through the environmental friendly processes. Furthermore, the used pulp mold can be easily recycled and the pulp mold itself is biodegradable. However, the higher cost and some deficiency in physical properties of pulp mold have been considered as issues to be overcome for a substitute for polymeric packaging materials such as EPS (Expandable Polystyrene). The way for the optimization of a pulp mold mill was proposed in this report. The possible reduction of drying energy was calculated by using a computer simulation method, which could Provide the detailed information about mass balance of overall process. The simulated results showed a great possible curtailment of production cost by improving the forming systems, for example, increasing the temperature and the dryness of a wet pulp mold.