• Food Engineering Progress
• /
• v.13 no.4
• /
• pp.341-347
• /
• 2009

Saengshik beverage products were developed to improve the convenience in consumption, and thereby to expand the Saengshik market. Beverages were prepared from 3 commercial Saengshik products (ES, BS, SS) by mixing with water using a high shear blender. The physicochemical and sensory properties of the Saengshik beverage product were compared. The most acceptable beverage product was made of BS at 7.7% (w/w) level. The apparent viscosity of the beverages increased as the Saengshik levels increased. The beverages at lower Saengshik levels showed dilatant fluid characteristics, while they were Newtonian and pseudoplastic fluids at middle and high Saengshik levels, respectively. The beverage products also showed rheopectic type time-dependency at middle (5.7-9.7%) Saengshik levels, while they were time independent at low and high levels.

• Steel and Composite Structures
• /
• v.38 no.5
• /
• pp.563-582
• /
• 2021

The present study experimentally and analytically investigated the push-out behaviour of H-shaped steel section embedded in ultrahigh-performance fibre-reinforced concrete (UHPFRC). The effect of significant parameters such as the concrete types, fibre content, embedded steel length, transverse reinforcement ratio and concrete cover on the bond stress, development of bond stress along the embedded length and failure mechanism has been reported. The test results show that the bond slip behaviour of steel-UHPFRC is different from the bond slip behaviour of steel-normal concrete and steel-high strength concrete. The bond-slip curves of steel-normal concrete and steel-high strength concrete exhibit brittle behaviour, and the bond strength decreases rapidly after reaching the peak load, with a residual bond strength of approximately one-half of the peak bond strength. The bond-slip curves of steel-UHPFRC show an obvious ductility, which exhibits a unique displacement pseudoplastic effect. The residual bond strength can still reach from 80% to 90% of the peak bond strength. Compared to steel-normal concrete, the transverse confinement of stirrups has a limited effect on the bond strength in the steel-UHPFRC substrate, but a higher stirrup ratio can improve cracking resistance. The experimental campaign quantifies the local bond stress development and finds that the strain distribution in steel follows an exponential rule along the steel embedded length. Based on the theory of mean bond and local bond stress, the present study proposes empirical approaches to predict the ultimate and residual bond resistance with satisfactory precision. The research findings serve to explain the interface bond mechanism between UHPFRC and steel, which is significant for the design of steel-UHPFRC composite structures and verify the feasibility of eliminating longitudinal rebars and stirrups by using UHPFRC in composite columns.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.438-442
• /
• 2005

Granule swelling is essential phenomenon of starch gelatinization in excess water, and characteristic of heated starch dispersion depends largely on size and distribution of swelled starch granule. Although swelling characteristic of starch granules depends on type of starch, heating rate, and moisture content, influence of heating rate on swelling phenomenon of starch granule has not been fully discussed, because constant heating rate of starch dispersion cannot be obtained by conventional heating method. Ohmic heating, electric-resistant heat generation method, applies alternative current to food materials, through which heating rate can be easily controlled precisely and conveniently at wide range of constant heating rates. Starch dispersion heated at low heating rates below $7.5^{\circ}C/min$ showed Newtonian fluid behavior, whereas showed pseudoplastic behavior at heating rates above $16.4^{\circ}C/min$. Apparent viscosity of starch dispersion increased linearly with increasing heating rate, and yield stress was dramatically increased at heating rates above $16.4^{\circ}C/min$. Average diameter of corn starch granules during ohmic heating was dramatically increased from $30.97\;to\;37.88\;{\mu}m$ by increasing heating rate from $0.6\;to\;16.4^{\circ}C/min$ (raw corn starch: $13.7\;{\mu}m$). Hardness of starch gel prepared with 15% corn starch dispersion after heating to $90^{\circ}C$ at different heating rates decreased gradually with increasing heating rate, then showed nearly constant value from $9.4\;to\;23.2^{\circ}C/min$. Hardness increased with increase of heating rate higher than $23.2^{\circ}C/min$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.5
• /
• pp.859-867
• /
• 1997

In order to utilize the processing wastes of squid, chitosans were manufactured from the pens of domestic squid, Todarbdes pacificus and foreign squid, Ommastrephes bartrami and then, its rheological properties were studied. The amounts of nitrogen and minerals of the domestic squid pens were $11.4\%\;and\;0.1\%$ respectively, whereas those of its chitosan were $7.5\%\;and\;0.2\%$. In case of foreign squid pen and chitosan, the amounts of nitrogen and minerals were $12.1\%,\;0.8\%\;and\;7.8\%,\;0.2\%$ respectively. Intrinsic viscosity $([\eta]) $ of domestic and foreign squid pen chitosans were decreased with increasing pH from 3.4 to 5.4 which might be due to the reduced repulsion in inter- of intra- chitosan molecules. Intrinsic viscosity of the domestic and foreign squid pen chitosans were decreased with increasing NaCl concentration thus indicated that the domestic and foreign squid pen chitosans were polyelectrolyte molecules and stiffness of squid pen thitosans were 0.11 similar to that of k-carrageenan. Flow type of squid pen chitosan solutions were pseudoplastic fluids without yield stress by the viscosity measurement. But the squid pen chitosan solutions showed newtonian fluid up to $0.15\~0.24\%$ concentration for domestic and $0.21\~0.24\%$ concentration for foreign at $10\~50\%$. Concentration dependence of consistency index in infinitive dilute domain (Kc) were higher in the dilute domain than entangled domain. Activation energies (Ea) of the squid pen chitosans were 3.7, 6.3, 3.6, 4.0 and 4.1 Kcal/g moi for domestic and 3.2, 3.1, 3.4, 3.8 and 3.6 Kcal/g mol for foreign at 0.1, 0.15, 0.25, 0.35 and $0.5\%$, respectively.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.1
• /
• pp.73-82
• /
• 2009

Injectable calcium phosphate cement (CPC) has been used as bone substitute successfully due to good biocompatibility and osteoconductivity. One of the important mechanical characteristics of CPC is flowablility, which can be evaluated by measuring rheological parameters. However, there have been few studies that measured rheological properties of CPC. The purpose of this study was to evaluate the effects of temperature and concentrations of 2 kinds of setting solutions, hydroxyprophyl methylcellulose (HPMC) and polyacrylic acid (PAA), on rheological properties of CPC. The CPC used was dicalcium phosphate dihydrate (DCPD). Rheological properties of CPC paste were measured using rheometer. The effect of concentrations of each solution (2% and 1% HPMC and 35% and 17.5% PAA) was evaluated. The effect of temperature ($25^{\circ}C$ and $37^{\circ}C$) on the rheological properties of CPC was also investigated. The statistical analysis was carried out with Mann-whitney test with Bonferronis collection. CPC with both setting solutions showed shear thinning behavior. Higher concentrations of setting solution (2% HPMC and 35% PAA) produced significantly higher viscosity than lower concentrations of setting solution (1% HPMC and 17.5% PAA). CPC with HPMC showed significantly higher viscosity at $37^{\circ}C$ that at $25^{\circ}C$. CPC with PAA showed lower viscosity at $37^{\circ}C$ than at $25^{\circ}C$, although the difference was not statistically significant. The results showed that CPC with HPMC or PAA solutions are pseudoplastic and the concentrations of setting solutions and temperature may have an effect on the rheological properties of CPC paste. These results showed that the flowability of injectable CPC could be improved by use of increasing frequency of oscillation. In clinical practice, the use of ultrasonic vibration would be helpful in application of injectable CPC. CPC with HPMC could be more easily applicated at $25^{\circ}C$ than $37^{\circ}C$. The use of lower concentrations of HPMC and PAA solution would be beneficial in terms of flowability.

• Korean Journal of Food Science and Technology
• /
• v.26 no.4
• /
• pp.442-447
• /
• 1994

Effect of different mixing ratio of non-glutinous and glutinous rice on physical and rheological properties of extrudate prepared in a single screw extruder were examined. The extrusion conditions in term of screw speeds, moisture content and die temperature were 258 rpm, 18% and $120^{\circ}C$, respectively. The resisdence time distribution of the most of materials were within 30 second and small portion of them went up to 80 second. The expansion ratio was the highest value (2.93) for 70% of glutinous rice in the mixture, while the lowest value for 100% of non-glutinous rice. Breaking strength was in the range between 1,051g and 1,117g for $10{\sim}20%$ of glutinous rice in the mixture, while the lowest value (737g) for 80%r of glutinous rice. As the amount of glutinous rice increased, L and a values were increased and b value was decreased. The uncooked cold paste viscosity had 400 B.U. for 100% non-glutinous rice , while no peak for the 100% glutinous rice. As the amount of glutinous rice increased up to 100%, the water absorption index (WAI) was decreased, while water solubility index (WSI) was increased. The rheological properties of extrudate were accounted by the law of Oswald. The flow behavior index of extrudate was less than 1.0, which showed pseudoplastic behavior. Yield stress was the highest value for 20% of glutinous rice in the mixture and the lowest value for $80{\sim}100%$ of glutinous; rice. Number of air cell was between 128 and 159 for $80{\sim}100%$ of glutinous rice in the mixture, while $81{\sim}84%$ for $0{\sim}20%$ of glutinous rice. The degree of shapefact was increased more when the mixtures of glutinous and non-glutinous rice was used than when glutinous or non-glutinous rice was only used.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.11a
• /
• pp.127-127
• /
• 2001

종이의 공극은 도공용 원지 또는 인쇄 용지로 사용될 때 도공액과 잉크 조성분의 침 투 거동에 영향을 미침으로써 여러 가지 물리적 성질에 변화를 가져온다. 도공 공정의 경우, 도공액에 포함되어 있는 물과 수용성 고분자 물질의 원지 침투는 도공 작업성과 도공층의 구조에 변화를 가져 올 수 있다. 이러한 변화는 물을 포함한 수용성 물질의 원지 침투가 빨라질 때 도공액의 고형화점 상승에 의한 원지 피복력 저하에 따른 도공 지의 평활성 감소를 가져온다. 또한 높은 전단력이 가해지는 블레이드 도공에서는 도피 직전 도공액의 수분 이탈이 급격하게 일어날 경우 블레이드에서 도공액의 유동성 저하 가 발생됨으로써 여러가지 문제점을 나타낸다고 보고 된 바 있다. 인쇄 공정의 경우에 는 도공층이 잉크의 직접적인 기질(substrate)로 작용되어 잉크 성분의 잔류 및 침투 거동에 영향을 미친다. 즉 지나치게’발달된공극 특성을 지닌 도공층에서는 잉크 안료가 적절한 결합력을 가지고 도공층에 정착되기 전에 잉크 속의 레진과 용제가 도공층의 공극으로 소실됨으로써 인쇄 완료 후 작은 외력에도 잉크 층이 파괴되는 효킹 ( (chalking) 현상이 일어난다. 그러나 과도한 바인더의 적용과 미세한 안료의 사용에 따 라 도공층의 공극이 폐쇄될 경우에는 인쇄 후 잉크의 건조가 늦어져 인쇄 작업성의 저 해 요인으로써 작용한다. 종이의 공극성과 인쇄적성은 주지하는 바와 같이 불가분의 관계에 있으며, 본 연구에 서는 피인쇄체로서 공극성을 달리한 세 종류의 도공지를 제조하고 실험실적으로 제조 된 잉크를 사용하여 각각의 특성에 따른 잉크의 잔류 특성에 대하여 고찰해 보고자 하 였다. 특히 인쇄 전 피인쇄체의 공극 특성에 따른 인쇄 전후의 공극율 변화와 주요 인 쇄 적성간의 관계에 대해 초점을 맞추었다.시아노에틸화한 PYA용액의 점탄성 평가를 위하여 storage modulus와 loss modulus 를 분석하였다. 일반적 유변특성 평가 결과 PYA용액은 shear-thinning, pseudoplastic 한 특성을 나타내어 표면사이즈 공정에서의 적용 가능성을 확인할 수 있었다. 사용하는 통계기법 중의 하나인 주성분회귀분석을 실시하였다. 주성분 분석은 여러 개의 반응변수에 대하여 얻어진 다변량 자료의 다차원적인 변 수들을 축소, 요약하는 차원의 단순화와 더불어 서로 상관되어있는 반응변수들 상호간 의 복잡한 구조를 분석하는 기법이다. 본 발표에서는 공정 자료를 활용하여 인공신경망 과 주성분분석을 통해 공정 트러블의 발생에 영향 하는 인자들을 보다 현실적으로 추 정하고, 그 대책을 모색함으로써 이를 최소화할 수 있는 방안을 소개하고자 한다.금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.11a
• /
• pp.59-59
• /
• 2001

전보에서 발표한 바와 같이, 대상 라이너지 제조공장의 습부 운전조건이 지극히 악화되어 있으며 초지 시스템이 지종교체 등의 충격에 전혀 완충작용을 못하는 이유로 는 용수를 포함한 지료의 전하특성을 조절해주지 못하기 때문인 것으로 판단되었다. 특 히 양이온성 고분자로서 유일하게 사용하고 있는 보류향상제가 적절히 작용하지 못하 기 때문에 보류도가 저하되고, 제품내에 보류되지 못한 다량의 미세분이 백수 중에 존 재함으로서 결과적으로 지료의 전기적 특성을 더욱 악화시키는 악순환이 되풀이 되는 것으로 판단되었다. 이와 같이 강하게 음으로 하전된 지료의 전기적 특성을 조절하기 위해서는 양이온성 고분자의 사용량을 증가시키거나 고분자의 전하밀도 또는 분자량을 변화시켜 보는 것이 일반적인 습부첨가제 사용방법이라고 할 수 있다. 따라서 대상 습부공정의 조업조건을 호전시키기 위해서는 적절한 보류향상시스 템의 적용이 가장 시급한 현안이라고 판단되어 선규 보류제의 현장적용시험을 수행한 결과, 백수의 COD와 미세분이 격감하고 탈수성이 향상되어 습부공정의 운전조건이 호 전됨을 관측할 수 있었다. 그러나 2달 이상에 걸친 보류제 현장적용시험 기간 중에 생 산된 라이너지의 제반 물성들은 별다른 변화를 관측할 수 없었다. 이는 적용된 보류제 의 상당 부분이 계내의 미세분과 작용하여 소모되기 때문으로 판단되었다. 본 연구에서는 보류제의 투입 이전에 보류제와는 상대적으로 저분자량과 고 전 하밀도를 가진 고분자 전해질 4종을 사용하여 라이너지 지료의 전하를 중화시키고자 하였으며, 이러한 공정으로 생산된 라이너지의 물성변화를 관측하였다. 물성으로는 파 열강도, 압축강도, 습윤인장강도 및 염료 고착능력 등을 살펴보았다.시아노에틸화한 PYA가 안정된 분자구조를 유지하고 있음을 확인할 수 있었다. 시아노에틸화한 PYA용액의 점탄성 평가를 위하여 storage modulus와 loss modulus 를 분석하였다. 일반적 유변특성 평가 결과 PYA용액은 shear-thinning, pseudoplastic 한 특성을 나타내어 표면사이즈 공정에서의 적용 가능성을 확인할 수 있었다. 사용하는 통계기법 중의 하나인 주성분회귀분석을 실시하였다. 주성분 분석은 여러 개의 반응변수에 대하여 얻어진 다변량 자료의 다차원적인 변 수들을 축소, 요약하는 차원의 단순화와 더불어 서로 상관되어있는 반응변수들 상호간 의 복잡한 구조를 분석하는 기법이다. 본 발표에서는 공정 자료를 활용하여 인공신경망 과 주성분분석을 통해 공정 트러블의 발생에 영향 하는 인자들을 보다 현실적으로 추 정하고, 그 대책을 모색함으로써 이를 최소화할 수 있는 방안을 소개하고자 한다.금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭

• Journal of Microbiology and Biotechnology
• /
• v.8 no.2
• /
• pp.171-177
• /
• 1998

The strain A49, which produces a new type of extracellular polysaccharide was isolated from soil samples. From morphological, physiological and biochemical tests, the strain A49 was identified as a Bacillus polymyxa and named Bacillus polymyxa A49. Bacillus polymyxa A49 was found to produce a highly viscous extracellular polysaccharide when grown aerobically in a medium containing glucose as the sole source of carbon. The polysaccharide (A49 POL) showed a homogeneous pattern on gel permeation chromatography (GPC) and its molecular weight was estimated to be about 1.6 mega dalton (mDa). The FT-IR spectrum of A49-POL revealed typical characteristics of polysaccharides. As a result of investigations with HPLC and carbozole assay, A49-POL was found to consist of L-fucose, D-galactose, D-glucose, D-mannose, and D-glucuronic acid, with the molar ratio of these sugars being approximately 1:2:7:50:12. Rheological analysis of A49 POL revealed that it is pseudoplastic and has a higher apparent viscosity at dilute concentrations than does xanthan gum. The consistancy factor of A49 POL was found to be higher, and the flow index of A49 POL lower, than xanthan gum. Its apparent viscosity was comparatively unstable at various temperatures. the A49 POL showed the highest apparent viscosity at pH 3. When salts were added to A49 POL solution, the solution was compatible with up to 10% KCl, 35% NaCl, 55% $CaCl_2$, 55% $MgCl_2$, 55% $K_2HPO_4$, and 110% $Ca({NO_3})_2$, respectively.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.21 no.1
• /
• pp.42-49
• /
• 1988

In order to utilize sea mustard, Undaria pinnatifida, effectively. sea mustard jam was prepared by use of physical properties of polysaccharides, mainly alginic acid and then its chemical composition, nutritive qualifies and the stability of pigments were examined. Suitable processing condition for sea mustard jam was as fellows : as the first stage, fresh sea mustard was scalded for 20 sec at $85^{\circ}C$ and dried sea mustard was dipped for 20 min in cold water for rehydration, then both sea mustards were treated by draining and chopping. Next, after adding 4 fold of $0.5\%\;K_2HPO_4$ solution to weight of chopped sea mustards, the mixed solutions were agitated for 15 min at $95^{\circ}C$, and gelated sea mustards were filterated by pressing. Flow characteristics of those sea mustard jam were regarded mixed type having pseudoplastic type and yield stress. Judging from sensory evaluation, adding $0.375\%$ of saccharin, $2\%$ of sorbitol, $0.25\%$ of citric acid and $0.5\%$ of powder of roasted soybean to sea mustard jam were suitable for enhancing taste and flavor of product. Chemical composition of products were scarcely changed throughtout processing. Jam processed by fresh sea mustard was better than dried one in contents of chlorophyll and total carotenoid pigments. In fatty acid composition, polyenoic acids of $C_{18:3},\;C_{20:4},\;C_{20:5},\;C_{22:6}$ were held high contents as known to have lowering function of cholesterol contents. It was presumed that dominant contents in free amino acids such as lysine, alanine, glutamic acid and organic acids such as citric acid, oxalic acid, $\alpha-ketoglutaric$ acid, lactic acid and succinic acid held important role for the flavor of sea mustard jam.