• 대한기계학회논문집A
• /
• 제21권2호
• /
• pp.281-287
• /
• 1997

In the conventional inverse modeling method for on-line modeling of the secondary path transfer function, the signal to noise ratio between the arbitrary random signal and the plant noise have to keep at -10 - -20 dB. For these reasons, the modeling can't be exactly implemented by the conventional method alone and the convergence time for modeling becomes too long. In this study, by combining the conventional inverse modeling method with an adaptive line enhancer, or with an adaptive noise canceller, a rigorous transfer functions of secondary path modeling and the control of a primary noise have been implemented simultaneously.

• 대한기계학회논문집A
• /
• 제38권11호
• /
• pp.1291-1297
• /
• 2014

본 논문에서는 자세 제어 장치와 능동 후륜 조향을 이용한 통합 섀시 제어를 제안한다. 제어에 필요한 요 모멘트를 만들어 내기 위해 직접 요 모멘트 제어 방법을 이용한다. 가중 역행렬 기반 제어할당 방법을 이용하여 제어 요 모멘트를 자세 제어 장치의 제동력과 능동 후륜 조향의 조향각으로 분배한다. 가중 역행렬 기반 제어 할당 방법에 가변 가중치를 도입하여 다양한 구동기 조합을 표현하고 차량의 속도를 높이기 위해 시뮬레이션을 이용하여 가변 가중치를 최적화한다. 차량 시뮬레이션 패키지인 CarSim 에서 시뮬레이션을 수행하여 제안된 방법이 차량의 조종안정성과 횡방향 안정성을 향상시킨다는 사실을 검증한다.

• 대한기계학회논문집A
• /
• 제24권8호
• /
• pp.1931-1939
• /
• 2000

Operating excitation forces of the linear vibratory system are normally determined by direct measurement techniques using load cells, strain gauges, etc. But, hydraulic forces of the rotating turbomachinery such as centrifugal pumps are exerted on an impeller due to asymmety of the flow by the interaction between pump impeller and volute. So, investigations of wide range of hydraulic designs and geometric deviations are difficult by direct method. This paper presents a hybrid approach for fourier transformed operational excitation forces, which uses pseudo-inverse matrix of the transfer matrix for the system and the measured vibrational data with standard installed pump. The determination of the transfer function matrix is based on a linear rotor/stationary system and steady state harmonic response in finite element analysis. And, vibrational data is collected in both vertical and horizontal directions at inboard and outboard bearing housings. The results of the process may be enhanced by making acceleration measurements at many more locations than there are forces to be determined.

• 한국항공우주학회지
• /
• 제36권7호
• /
• pp.651-657
• /
• 2008

본 논문에서는 저사양의 반작용 휠을 이용하여 토크 가용성을 높이는 두 가지 기법이 제안 하였다. 첫 번째는 기존의 의사역행렬을 이용한 토크 제어 분배 법칙 대신 가중치가변 의사역행렬과 모멘텀을 최소화하는 제어 분배 법칙을 제안하여 반작용 휠의 토크, 모멘텀 제한 조건 내의 해를 찾도록 했다. 두 번째는 휠의 장착각을 변경하여 토크가 많이 필요한 축의 토크 가용성 자체를 증가시키는 방법을 제안하였다. 제안된 법칙들은 위성체의 자세 천이에 적용되었으며, 시뮬레이션을 통하여 성능 향상과 실제 위성의 적용 가능성을 기술했다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.93.1-93
• /
• 2001

An evolutionary approach for the design of Fuzzy Logic Systems(FLSs) is proposed. Membership functions(MFs) in Takagi-Sugeno type fuzzy logic system is optimized through evolutionary process. Output singleton values are obtained through pseudo-inverse method. The proposed technique is unique for that, to prevent overfilling phenomenon, limited-level RBF membership functions are used and the new fitness function is invented. To show the effectiveness of the proposed method, some simulations results on model identification are given.

• 대한수학회논문집
• /
• 제16권3호
• /
• pp.487-508
• /
• 2001

We consider the Cauchy problem for Laplacian. Using the single layer representation, we obtain an equivalent system of boundary integral equations. We show the singular values of the ill-posed Cauchy operator decay exponentially, which means that a small error is exponentially amplified in the solution of the Cauchy problem. We show the decaying rate is dependent on the geometry of he domain, which provides the information on the choice of numerically meaningful modes. We suggest a pseudo-inverse regularization method based on singular value decomposition and present various numerical simulations.

• Smart Structures and Systems
• /
• 제31권5호
• /
• pp.437-454
• /
• 2023

Real-time hybrid simulation (RTHS), which has the advantages of a substructure pseudo-dynamic test, is widely used to investigate the rate-dependent mechanical response of structures under earthquake excitation. However, time delay in RTHS can cause inaccurate results and experimental instabilities. Thus, this study proposes a model-based adaptive control strategy using a Kalman filter (KF) to minimize the time delay and improve RTHS stability and accuracy. In this method, the adaptive control strategy consists of three parts-a feedforward controller based on the discrete inverse model of a servohydraulic actuator and physical specimen, a parameter estimator using the KF, and a feedback controller. The KF with the feedforward controller can significantly reduce the variable time delay due to its fast convergence and high sensitivity to the error between the desired displacement and the measured one. The feedback control can remedy the residual time delay and minimize the method's dependence on the inverse model, thereby improving the robustness of the proposed control method. The tracking performance and parametric studies are conducted using the benchmark problem in RTHS. The results reveal that better tracking performance can be obtained, and the KF's initial settings have limited influence on the proposed strategy. Virtual RTHSs are conducted with linear and nonlinear physical substructures, respectively, and the results indicate brilliant tracking performance and superb robustness of the proposed method.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권12호
• /
• pp.679-684
• /
• 2000

Closing switch, key component of pulsed power system, is constructed simply and used frequently due to the easy control and manufacture of one. The kind of one are spark-gap, triggered vacuum switch, pseudo-spark switch and INPIStron. But the electrode of spark gap switch is damaged with the hot spot by Z-pinch and then the life of one become short. INPIStron with inverse pinch effect has long life but it is difficult trigger system to provide uniform discharge between cathode and anode. In this paper, the design and manufacturing of INPIStron with gas puffing trigger method in order to supply uniform discharge inter-electrode and the performance of the developed INPIStron applied to 500[kA]-2[MJ] pulsed power system is presented.

• 한국정밀공학회지
• /
• 제10권4호
• /
• pp.200-205
• /
• 1993

In many applications, the typical parallel-jaw end-effector of a robot arm has been remarkably satisfactory. But, it is not adequate for the applications such as complicated manipulation. In the study, a finger with 4 joints (so, having redundancy) was consturcted to investigate the characteristics of an articulated hand. Each joint was driven by one actuator, and the motor torque was transmited to each joint through a tendon-pulley system. In the context, major considerations for hardware design and the method to solve the inverse kinematics of a redundant manipulator were presented. Finally, the basic capabilities of an articulated hand were presented through experiments.

• 한국정밀공학회지
• /
• 제10권2호
• /
• pp.170-177
• /
• 1993

In robotic arc welding, the roll (rotation) of the torch about its direction vector does not have any effect on the welding operation. Thus we could use this redundant degree of greedom for the motion control of the robot manipulator. This paper presents an algorithm for the pseudo- inverse kinematic motion control of the 6-axis robot, which utilizes the above mentioned redunancy. The prototype welding operation and the tool path are also graphically simulated. Since the proposed algorithm requires only the position and normal vector of the weldine as an input data, it is useful for the CAD-based off-line programming of the arc welding robot. In addition, it also has the advantages of the redundant manipulator motion control, like singularity avoidance and collision free motion planning, when compared with the other motion control method based on the direct inverse kinematics.