• 터널과지하공간
• /
• 제7권1호
• /
• pp.13-19
• /
• 1997

It is necessary to study on thermo-hydro-mechanical effect at rock mass performing project such as radiowaste disposal in deep rock mass. In this study, thermo-hydro-mechanical coupling analysis which is considered interaction and the variation of rock properties induced by temperature increase was performed for the circular shaft when appling temperature of 20$0^{\circ}C$ at the shaft wall. The shaft is diameter of 2 m and under hydrostatic stress of 5 MPa. In the cases, thermal expansion by temperature increase progress from the wall to outward and thermal expansion could induce tensile stress over the tensile strength of rock mass at the wall. When rock properties were given as a function of temperature, thermal expansion increased, tensile stress zone expanded. Lately, water flow is activated by increase of permeability and decrease of viscosity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1599-1601
• /
• 2000

To study invar alloy as a core material for large ampacity over-head transmission line which have high strength and low thermal expansion coefficient simultaneously, thermal expansion coefficient, physical properties and hardness of Fe-Ni-Co-xC alloy have been studied. It is necessary that invar alloy possess low thermal expansion coefficient and high strength for increased capacity over-head transmission line. In this paper we tried to find out the effect of carbon addition related with mechanical and physical properties. It was found that the thermal expansion coefficient and hardness were increased with carbon addition for whole composition range but the saturation magnetization was decreased except for the range of 0.1$\sim$0.4%C.

• Carbon letters
• /
• 제1권2호
• /
• pp.76-81
• /
• 2000

Physical properties of artificial graphite electrodes were evaluated along three different directions; circumferential (X), radial (Y), and axial (Z) directions. Four kinds of commercial electrode products were used in this study for the evaluation; pole (AP) and nipple (AN) of manufacturer A, pole (BP) and nipple (BN) of manufacturer B. The mechanical, electrical, and thermal properties in X and Y directions were very similar to each other. In Z direction, however, the mechanical properties, including flexural strength and compressive strength, were higher, and electric resistance and thermal expansion were much lower than those in the other directions. The microstructures observed by optical microscope and scanning electron microscope revealed that the differences in properties by the measuring direction were caused by the preferential alignment of needle cokes along the Z direction. When comparing the properties of the electrode samples in the same direction, the mechanical properties mainly depended on the bulk density or porosity of the samples as well as preferential alignment of needle cokes.

• 한국의류학회지
• /
• 제23권1호
• /
• pp.22-29
• /
• 1999

This paper descrived the changes of peel strength wrinkle recovery and dimensional stability after fusing 4 different wool face fabrics with 3 different fusible interlinings. The fusing condition was conducted by fusing press machine under 4kg.f/cm2 at 15$0^{\circ}C$. To determine the effect of the varous physical properties of the fused fabrics face fabrics and interlinings on the peel strength wrinkle recovery and dimensional stability(hygral expansion and relaxation shrinkage) of fused fabrics correlation among the KES values of fused fabrics face fabrics and interlinings to the peel strength rinkle recovery and dimensional stability of fused fabrics were expeerimentally analyzed,. As the results the peel strength was mainly influenced by the cover factor of face fabric and interlinings. After fusing wrinkle recovery and hygral expansion were decreased. The cover factor wrinkle recovery weight thickness shear rigidity and frictional properties of face fabric and the thickness of fused fabrics were not influence to the wrinkle recovery of fused fabrics. In addition the dimensional stabilities of fused fabrics were mainly influenced by the tensile and frictional properties of the wrinkle recovery of fused fabrics. In addition the dimensional stabilities of fused fabrics were mainly influenced by the tensile and frictional properties of the face fabrics.

• 산업경영시스템학회지
• /
• 제33권1호
• /
• pp.71-79
• /
• 2010

This paper addresses capacity expansion planning model of distribution center under usability of public distribution center. For discrete and finite time periods, demands for distribution center increase dynamically. The capacity expansion planning is to determine the capacity expansion size of private distribution center and usage size of public distribution center for each period through the time periods. The capacity expansion of private distribution center or lease usage of public distribution center must be done to satisfy demand increase for distribution center. The costs are capacity expansion cost and excess capacity holding cost of private distribution center, lease usage cost of public distribution center. Capacity expansion planning of minimizing the total costs is mathematically modelled. The properties of optimal solution are characterized and a dynamic programming algorithm is developed. A numerical example is shown to explain the problem.

• 한국주조공학회지
• /
• 제23권4호
• /
• pp.195-203
• /
• 2003

Hyper-eutectic Al-Si alloy is used much to automatic parts and material for the electronic parts because of the low coefficient of thermal expansion, superior thermal stability and superior wear resistance. In this work, A390 alloy specimens were fabricated for control of the Si particle size by various processes, such as spray-casting, permanent mold-casting and squeeze-casting. To minimize the effect of microporosity of the specimens, hot extrusion was carried out under equal condition. Each specimens were evaluated tensile properties at room temperature and thermal expansion properties in the range from room temperature to 400$^{\circ}C$. Ultimate tensile strength and elongation of the spray-cast and extruded specimens which have fine and well distributed Si particles were improved greatly compare to the permanent mold-cast and extruded ones. Specimens which have finer Si particles showed higher ultimate tensile strength and elongation than those having large Si particle size, and coefficient of thermal expansion of the specimens increased linearly with Si particle size. In case of the repeated high temperature exposures, thermal expansion properties of the spray-cast and extruded specimens were found to be more stable than those of the others due to the effect of fine and well distributed Si particles.

• 전기학회논문지
• /
• 제65권9호
• /
• pp.1504-1510
• /
• 2016

The aim of this study is to improve properties both glass transition temperature($T_g$) and coefficient of thermal expansion(CTE) using epoxy/micro-nano alumina composites with adding glycerol diglycidyl ether (GDE:1,2,3,5g). This paper deals with the effects of GDE addition for epoxy/micro alumina contents (40, 50, 60wt%)+surface modified nano alumina(1_phr) composites. 20 kinds specimen were prepared with containing micro, nano alumina and GDE as a micro composites(10, 20, 30, 40, 50, 60, 70wt%) or a nano/micro alumina composites(1phr/40, 50, 60wt%). Average particle size of nano and micro alumina used were 30nm and $1{\sim}2{\mu}m$, respectively. The micro alumina used were alpha phase with Heterogeneous and nano alumina were gamma phase particles of spherical shape. The glass transition temperature and coefficients of thermal expansion was evaluated by DSC and TMA. The glass transition temperature decreased and coefficients of thermal expansion become smaller with filled contents of epoxy/micro alumina composites. On the other hand, $T_g$ and CTE as GDE addition variation(1,2,3,5g) of epoxy/micro-nano alumina composites decreased and increased respectively.

• 한국전기전자재료학회논문지
• /
• 제34권5호
• /
• pp.337-341
• /
• 2021

Phase evolution, thermal and microwave dielectric properties of cordierite-Al₂O₃ composite were investigated. As the content of Al₂O₃ increased, mullite, sapphirine, and spinel were formed as secondary phases, implying that cordierite may be decomposed by the reaction with Al₂O₃. All sintered specimens exhibited dense microstructures. The densification occurred through liquid phase sintering. As the content of Al₂O₃ increased, the thermal expansion coefficient and the dielectric constant increased, whereas the quality factor decreased. The thermal expansion coefficient, the dielectric constant, and the quality factor of the 90 wt% cordierite 10 wt% Al₂O₃ composite sintered at 1,425℃ were 2.9×10^-6 K^-1, 5.1, and 34,844 GHz, respectively.

• 한국세라믹학회지
• /
• 제40권11호
• /
• pp.1127-1131
• /
• 2003

인삼염유리는 전자부품분야에서 저온소성유리로 그 활용범위가 넓은 편이나 높은 열팽창계수로 알칼리 산화물 등을 첨가하여 그 특성을 조정하고 있다. 본 연구에서는 P$_2$O$_{5}$-SnO-ZnO-SiO$_2$/B$_2$O$_3$ 유리계에 대하여 열적특성으로 선팽창계수와 유리전이온도, 용융온도 등을 측정하여 그들 값의 상관관계를 고찰하였다. 이러한 결과는 다른 인삼염 유리와 비교하였을때 선팽창계수와 유리전이온도의 곱이 일정한 값으로 나타나서 이들 중의 하나의 값으로부터 간접적으로 다른 변수를 측정 할 수 있는 한 방법이 될 수 있다.

• 콘크리트학회논문집
• /
• 제14권3호
• /
• pp.440-448
• /
• 2002

산업의 발달과 더불어 폐유리의 발생량은 점차 증가되고 있다. 콘크리트에 폐유리를 사용할 경우 알칼리 실리카 반응(ASR)에 의한 팽창으로 콘크리트에 균열이 발생하여 성능저하를 일으킬 수 있다. 본 연구에서는 폐유리의 색깔(갈색, 녹색), 입도 및 폐유리로 인해 발생되는 ASR팽창을 저감시키기 위해 산업부산물의 종류(플라이애시, 고로슬래그 미분말)와 혼입율에 따른 ASR팽창과 강도특성을 분석하였다. 또한, 포졸란 재료로서 폐유리 분말의 사용가능성을 분석하였다. 연구결과, 폐유리의 색깔에 관계없이 폐유리의 퍼시멈 입도는 2.5~l.2mm로 나타났으며, 폐유리의 입도가 2.5~l.2 mm보다 작을수록 팽창은 점차 감소하는 것으로 나타났다. 또한, 폐유리에 산업부산물의 혼입은 ASR로 인한 팽창과 강도저하를 억제시키는데 효과적이며, 0.075 mm미만의 폐유리 분말이 포졸란 재료로서 적용이 가능한 것으로 나타났다.