• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.1-8
• /
• 2014

In this study, the influence of the physical properties of ink such as ink dispersity and emulsified amount on the printability of a coated paper was investigated with seven kinds of cyan inks. In addition, two kinds of coating formulations were tested to evaluate the effect of coating structure on the coated paper printability. It was found that the cyan ink with $2{\mu}m$ pigment size had the best dispersibility and hence the ink showed a best ink density on the two kinds of coated papers. When the emulsified ink A with IPA 20 wt% had a lower viscosity than emulsified ink B with IPA 10 wt%, the emulsified ink A showed relatively high value of the ink transfer rate in comparison with emulsified ink B. Despite the high value of ink transfer rate, the coated paper did not show a good printability because those inks with low viscosity due to a strong emulsification were easy to make print mottle on the coated paper.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.175-182
• /
• 1996

This paper deals with the properties of water permeability and porosity of cement mortar substrate coated with siliceous slurry coating under the exposure environment. Conditions of exposure enviornment are four kinds of in constant temperature water and humidity box, in indoor and outdoor exposure. Coated mortar substrate was expected continually increase in water and humidity condition, but was not in dry condition. Watertightness effect of siliceous coating was better in the condition of humidity then the dry condition, and the pore volume was decreased in that condition.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.41-48
• /
• 2001

This paper was made to evaluate the effect of the type of latex for coating on the printability by investigating the structure of pore such as the pore fraction, the number of pores, pore size and distribution of coated paper. The coated structure is mainly depend on the results of interaction between pigment and binder. It means that the structure of pore formed is chiefly affected by the type of latex. This physical properties of pore have a close relation with ink set-off associated with the drying rate, the speed of penetration of ink into base paper and printing gloss. Therefore it was necessary to find out the relationship between pore structure and the performance of printability by modifying the type of latex to vary the pore structure of coated paper. Acrylic latex was superior to S/B latex in the sedimentation volume, compressibility, smoothness, pore fraction and its number, the weight of transferred ink onto the coated paper and ink repellance. In contrast, water retention and ink setting were not good. in the comparison of anionic and amphoteric latex, amphoteric latex showed better performance in the thickness, smoothness, pore fraction and its number, pore size, the weight of ink transmitted and K&N ink receptivity, etc.

• KSTLE International Journal
• /
• v.10 no.1_2
• /
• pp.1-5
• /
• 2009

This paper reports an investigation on nanotribological properties of silicon nanochannels coated by a diamond-like carbon (DLC) film. The nanochannels were fabricated on Si (100) wafers by using photolithography and reactive ion etching (RIE) techniques. The channeled surfaces (Si channels) were then further modified by coating thin DLC film. Water contact angle of the modified and unmodified Si surfaces was examined by an anglemeter using the sessile-drop method. Nanotribological properties, namely friction and adhesion forces, of the Si channels coated with DLC (DLC-coated Si channels) were investigated in comparison with those of the flat Si, DLC-coated flat Si (flat DLC), and Si channels, using an atomic force microscope (AFM). Results showed that the DLC-coated Si channels greatly increased hydrophobicity of silicon surfaces. The DLC coating and Si channels themselves individually reduced adhesion and friction forces of the flat Si. Further, the DLC-coated Si channels exhibited the lowest values of these forces, owing to the combined effect of reduced contact area through the channeling and low surface energy of the DLC. This combined modification could prove a promising method for tribological applications at small scales.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.483-486
• /
• 2000

In the recognition of the gases using the quartz crystal rnicrobalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing chararcteristics of film is changed with these. In this paper, we coated the lipid GC materials varing with the blended amount of PVC(Po1y Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of 20.4 respectively. Also, we measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.3
• /
• pp.53-58
• /
• 2002

This paper was performed to investigate the effect of pore structure on ink residual behavior. To prepare different coating structures as substrates against inks, fine, medium and coarse calcium carbonate were used in the coating color. It is well known ink properties can affect to print qualities. After printing on the coated paper, ink layer can consider as third structure addition to paper and coating layer. To compare effect of ink properties on the surface structure and print qualities, several properties of ink were also adopted as raw material. Particle size of pigment effect on gloss evaluation of coated paper increased with calendering. It was shown that ink transfer rate increased as surface of the sample was smooth. The ink contained low viscosity resin evaluated more print gloss. Finer pigment particle size, smaller pore size and higher porosity. Pore volume of coated paper was slightly decreased with printing as the coating was prepared with the finest particle size. However, it founded that ink resin could not affect on pore volume and distribution of printed paper

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.28 no.2
• /
• pp.81-87
• /
• 2022

Paper is a promising alternative to petroleum-based plastic materials for sustainable packaging applications. However, paper exhibits poor gas and water vapor barrier properties, which restrict its effective application in the packaging industry. To enhance the properties of papers, sodium caseinate (CasNa)/transglutaminase (TG) coating solutions with various TG contents were prepared and coated on the papers. The chemical and morphological structures, mechanical properties, seal strength, and water vapor barrier properties of the coated papers were thoroughly investigated. The paper properties depended significantly on the chemical and morphological structures. Pristine CasNa and CasNa/TG coating solutions were evenly coated on the paper surfaces, without any cracks. The chemical structure of the CasNa/TG coated papers was slightly influenced by TG addition, resulting in increased elongation at break and enhanced water barrier properties. To promote the use of CasNa-coated papers in packaging applications, additional investigations must be performed to prevent gas and moisture permeation and enhance the mechanical strength of these papers via chemical reactions and introduction of organic/inorganic composites.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.04a
• /
• pp.339-347
• /
• 2011

This study was carried out in order to manufacture the high quality coated paper. High quality coated paper includes not only present state but also the state of the future. So in this study, acrylic-styrene emulsion which polymerized in laboratory was compared with SB(Styrene-butadiene) latex during thermal aging. The coated paper with three different formulations which controlled the dosage of acrylic-styrene emulsion were prepared. The coated paper were thermally aged at $105^{\circ}C$ for 18days and the optical properties were measured. Brightness, whiteness and CIE L value were higher during thermal aging with increasing amount of acrylic-styrene emulsion. CIE $a^*$ value was higher and CIE $b^*$ value decreased with increasing amount of acrylic-styrene emulsion. These results indicate that high quality coated paper which has anti -thermal aging property can be manufactured with acrylic-styrene emulsion.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.1
• /
• pp.37-45
• /
• 2002

The effect of soft nip calendering variables including pressure, temperature, nip residence time and sheet moisture on the properties of coated papers was investigated. The change of gloss, opacity, bulk and brightness were determined after calendering. Increase of calendering pressure and temperature increased gloss, but it decreased opacity, bulk and brightness of coated papers. Nip residence time and sheet moisture content showed similar effects on these properties. Calendering conditions of 16$0^{\circ}C$ of temperature, 146kg$_{f}$/cm of line load or less were found to provide optimum conditions to obtain reasonable gloss and smoothness while minimizing the loss of bulk and opacity for coated papers.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.75-82
• /
• 1997

To improve the quality of coated paper, the continuous research to the coating components and development of alternative latices is required. Recently, amphoteric latex is getting a great concern due to their changable properties of surface charge through controlling pH and some methods have been tried to prepare amphoteric latices. This study was carried out to synthesize amphoteric latex using seeding polymerization method with low concentration emulsifier. Styrene was used as a main monomer in addition to acrylonitrile for a hydrophilic comonomer. acrylic acid for a anionic comonomer and N,N-dimethylaminoethyl methacrylate for a cationic comonomer. Particle size and viscosity of latex were greatly affected by addition of acrylic acid and ammonium persulfate as an initiator. Negative charge of latex in alkali condition was changed to zero to positive charge in around pH 4.