• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.78-81
• /
• 2002

Printed Circuit Boards for satellite are composed of multi-layered copper plate and glass epoxy. Each copper layer have the complicated and different pattern to operate correctly for its mission. Especially. copper layer give effect on the PCB stiffness seriously. But It can make more complicate to predict the exact stiffness of PCB. In KOMPSAT-2 program, too many type of PCB are used for each electronic unit, and they have different type of pattern of copper layer. Solar array regulator has two type of PCB and it will be considered for this study. In this study. we calculate the PCB board stiffness of KOMPSAT-2 SAR unit considering the concept of simplified representative volume element. It will be correlated with the test results under KOMPSAT-2 vibration environmental condition to increase the reliability of this study.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.318-320
• /
• 2009

A switchable Yagi-Uda antenna prototype with radiation pattern reconfiguration is presented in this letter. The proposed reconfigurable antenna is based on the concept of switching between the reflector and director of a Yagi-Uda antenna using a radio frequency PIN diode. As a result, the minimum/maximum radiation can be steered towards desired signals or away from interfering signals in opposite directions. The measured 10 dB impedance bandwidth and gain are 210 MHz (7%) and 8.02 dBi at 3 GHz, respectively. Details of the antenna design and its performance are described and empirically analyzed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.926-931
• /
• 2005

In this paper, the printed-sleeve monopole antenna which has the small size and the broadband characteristics, is presented and its radiation characteristics are investigated. To conform the broadband characteristics of the proposed antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in PCS band (1.75 GHz${\~}$1.87 GHz). It is shown that the designed antenna has the non-directional pattern in the horizontal plane, the directional pattern in the vertical plane, VSWR less than 1.5, and gain in 2.14 dBi${\~}$3.4 dBi. From these results, the proposed antenna is conformed as a broadband antenna which can be used for the mobile communication indoor antenna extensively.

• Proceedings of the KIEE Conference
• /
• 2007.11a
• /
• pp.104-105
• /
• 2007

In this study, characteristics of silver ink-jet printing were investigated under various substrate treatments such as substrate heating, hydrophobic coating, and ultraviolet(UV)/ozone soaking. Fluorocarbon(FC) film was spin-coated on the polyimide (PI) film substrate to obtain a hydrophobic surface. Although hydrophobicity of the FC film could reduce the diameter of the printed droplets, the singlet images printed on the FC film surface showed irregularities in the pattern size and the position of the printed droplet along with droplet merging phenomenon. The proposed UV/ozone soaking of the FC film improved the uniformity of the pattern size and the droplet position after printing and substrate heating was very effective way in preventing droplet merging. By heating of the substrate after UV/ozone soaking of the coated FC film, silver conductive lines of 78-116 ${\mu}m$ line were successfully printed at low substrate temperatures of $40^{\circ}C$.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.65-70
• /
• 2011

These days, printed electronics attract attention from electronics industry. In this paper, the fabrication of the fine patterns by Near Field Electro Spinning (NFES) was studied by using Ag ink on silicon wafer (substrate). Two types of ink, the high viscous ink Ag-200 and low viscous ink Ag-15, were used. The fine and uniform patterns were easily fabricated by using Ag-200 because jet breakup is less occurred in high viscosity solution. As increasing flow rate of solution, aspect ratio of Ag pattern decreased. And there was optimum applied voltage for fine pattern. In case of Ag-200, the optimum applied voltage was about 2.02KV. When pattern was fabricated by NFES, the pattern width and height were affected by many factors such as viscosity, flow rate of solution, applied voltage etc.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.136-138
• /
• 2006

Recently a lots of problems have observed in high densified and high integrated electronic components. One of them is ion migration phenomena, which induce the electrical short of electrical circuit. Ion migration phenomena has been observed in the field of exposing the specific environment and using for a long time. Also as the RoHS restriction was started in July 1st, 2006, Pb-free solder was utilized in electronics assemblies. In this case, it is very important to compatible between components and printed circuit board(PCB), thus surface treatment materials of PCB was changed to Sn, Sn-3.0Ag-0.5Cu, Cu. Therefore these new application become to need to reevaluate the sensitivity about electrochemical ion migration. This study was evaluated the occurrence time of electrochemical ion migration using by water drop test. We utilized PCB(printed circuit board) having a comb pattern as follows 0.1, 0.318, 0.5, 1.0 mm pattern distance. Sn-3.0Ag-0.5Cu and Sn-37Pb were electroplated on the comb pattern. 6.5V and 15.0V were applied in the comb pattern and then we measured the electrical short time causing by occurring the ion migration. In these results, we evaluate the sensitivity and derived the prediction models of ion migration occurrence time depending on the pattern materials, applied voltage and pattern spacing of PCB conductor.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.63.1-63.1
• /
• 2012

In recent years, the functional inks for printed electronics that can be combined with a variety of printing techniques have attracted increasingly significant interest for use in low cost, large area, high performance integrated electronics and microelectronics. In particular, the development of solution-processable conductor, semiconductor and insulator materials is of great importance as such materials have decisive impacts on the electrical performance of various electronic devices, and, therefore, need to meet various requirements including solution processability, high electrical performance, and environmental stability. Semiconductor inks such as IGO, CIGS are synthesized by chemical solution method and microwave reaction method for TFT and solar cell application. Fine circuit pattern with high conductivity, which is valuable for flexible electrode for PCB and TSP devices, can be printed with highly concentrated and stabilized conductor inks such as silver and copper. Solution processed insulator such as polyimide derivatives can be use to all printed TFT device. Our research results of functional inks for printed electronics provide a recent trends and issues on this area.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.2
• /
• pp.208-217
• /
• 2001

Model-based color image halftoning method using dot-pattern database is proposed for low-resolution color image printing. Dot-pattern database used in the proposed method is based on Blue-Noise Mask. The database consists of dot-patterns constructed by circular dot-overlap model according to each color value. In halftoning procedure, input color value is reproduced as the dot-pattern selected to minimize the difference between the color values of the original image and those of the printed image. Also, the contrast sensitivity function as a human visual model is used to improve the perceived quality of the printed image in dot-pattern selection. Thus, the proposed method can substantially reproduce the color values of the pixels in original image and obtain better image quality. In the experiment, the proposed method has less ΔΕ/Sub ab/ between the original image in monitor and the printed one than that of ED and BNM halftoning. This result approves that the proposed method reproduces better image quality.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.8 no.3
• /
• pp.129-143
• /
• 2006

This study is to review the printed cotton textile industry of Europe in 17th-l8th century, and specially investigate the development of the Toile do Jouy, printed French fabrics around the 18th century. Generally, the Toile de Jouy has two different meanings. The first meaning is the popular printed cotton textiles producted by wood block printing, copper plate printing and roller printing techniques at Jouy on Joas factory in France, around 18th century. The second meaning is the monochromatic upholstery fabrics printed by copper plate. Actually, this monochromatic printed textiles were the most popular printed cotton fabrics with large scale scenic designs with people, trees, birds, buildings, mythical heroes, protagonists of novel and country scenes of shepherds, sheep and other animals manufactured by Jouy on Joas factory. Main issue of this paper is to propose features of pattern, color and classify types of patterns expressed on the Toile de Jouy fabrics according to printing techniques such as wood block printing, copper plate printing and copper roller printing. And this study is also to analyze on origins of the variety of names called the printed cotton textiles in those days. The results of this study can help to understand the knowledge of printed cotton textiles in Europe and be effectively applied to develop printed fabric design in the textile industry.