• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.838-845
• /
• 2006

Recently construction work in Korea, demands of favorable condition ground had been increased with industrialization acceleration and economic growth. However, because of limited land space, it was so hard to ensure favorable condition grounds that construction work proceeds until soft ground area on plans of road, railroad and industrial complex. In this case, soft ground improvement was required such as a stone column method. Stone column method, making a compaction pile using crushed stone, is a soft ground improvement method. However, stone column method is difficult to apply to the ground which is not mobilized enough lateral confine pressure because no bulging failure resistance. Hence, in present study, evaluates the stone columns reinforced by geogrid for settlement reduction and wide range of application of stone columns. Triaxial compression tests were conducted for evaluation which is about behavior characteristics of stone column on replacement rate. Then, 3-dimensional numerical analysis were conducted for application of stone column reinforced by geogrid as evaluate behavior characteristics and settlement reduction effect of stone column reinforced by geogrid on reinforcing depth change of geogrid.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.691-699
• /
• 2008

In the design of a foundation, settlement of the foundation may exceed allowable design criteria even with a competent bearing stratum. In such a case, a piled-raft foundation system may be adopted using piles as settlement reducing component. In this paper, Disconnected Piled Raft Foundation (DPRF) system, which installs disconnected piles underneath the raft and uses the piles as ground reinforcements, is studied as a cost effective design method against the classical piled-raft foundation system. To this end, large size loading tests were carried out on weathered ground changing area replacement ratio and length of piles. The results indicated that the settlement of the reinforced ground was reduced by 34~87% and the allowable bearing pressure increased by 70% on average from those of the unreinforced original ground, respectively. The correlating formula between the area replacement ratio and the load bearing ratio of piles were derived from the test results and numerical analysis. From the correlation, a design method determining the size and the quantity of the disconnected piles to enhance the bearing capacity of original ground to the desired value was proposed based on one inch settlement criteria.

• 한국지반신소재학회논문집
• /
• 제7권3호
• /
• pp.25-30
• /
• 2008

본 논문에서는 순환골재 다공질 콘크리트말뚝(RAPP)공법에 대한 실내모형실험의 결과를 바탕으로 RAPP로 개량된 복합지반의 침하 및 압밀 거동 특성을 분석하였다. 이를 위하여 실내모형실험에서 관측된 복합지반의 침하량과 무보강 지반의 침하량을 비교하여 복합지반의 침하저감효과를 분석하였으며 복합지반의 압밀도를 산정하여 RAPP공법으로 인한 압밀촉진효과를 검토 하였다. RAPP공법으로 인한 복합지반의 침하저감효과는 상재하중증분이 증가할수록 감소하였으나 전반적으로 SCP공법에 의한 효과보다 크게 나타났으며 압밀촉진효과는 SCP공법과 유사하게 나타났다.

• 한국지반공학회논문집
• /
• 제17권6호
• /
• pp.53-67
• /
• 2001

본 연구에서는 침하가 발생한 연약지반에 대하여 저유동성 몰탈에 의한 주입공법인 CGS공법의 적용성과 침하억제 효과를 확인하기 위하여 시험시공을 실시하고 그 결과를 분석하였다. 시험시공 현장은 파일에 의하여 지지된 기 시공 된 아파트의 주변지반으로서 사전에 sand drain공법으로 지반에 대한 처리를 실시하였으나 이후에도 지속적인 침하가 발생하고 있는 연약지반이다. CGS주입 전. 후의 지반개량특성을 파악하기 위하여 현장 및 실내토질시험과, 주입시공 중 거동특성을 파악하기 위하여 계측관리와 FDM해석을 실시하였다. 분석결과 연약지반의 지반침하 방지를 주목적으로 하는 CGS공법은 지반조건에 적합한 설치직경, 간격, 심도, 주입재, 주입압 등 다양한 조건으로부터 시공관리가 가능하며, 따라서 설치된 CGS구체는 파일의 지지효과와 더불어 주변지반을 압축강화시켜 복합적으로 지반을 개량시키므로 N치가 평균 2.1 증가하는 등 지반의 지지력 증대 및 침하억제에 효과가 있었다. 또한 적용성 있는 다양한 현장에 일반적으로 사용하게 될 경우 개량효과와 더불어 경제성이 확보될 수 있을 것으로 기대된다.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.315-328
• /
• 2019

This paper presents an investigation on bearing capacity, load-settlement behavior and safety factor of rock-soil slopes reinforced using geogrid-box method (GBM). To this end, small-scale laboratory studies were carried out to study the load-settlement response of a circular footing resting on unreinforced and reinforced rock-soil slopes. Several parameters including unit weight of rock-soil materials (loose- and dense-packing modes), slope height, location of footing relative to the slope crest, and geogrid tensile strength were studied. A series of finite element analysis were conducted using ABAQUS software to predict the bearing capacity behavior of slopes. Limit equilibrium and finite element analysis were also performed using commercially available software SLIDE and ABAQUS, respectively to calculate the safety factor. It was found that stabilization of rock-soil slopes using GBM significantly improves the bearing capacity and settlement behavior of slopes. It was established that, the displacement contours in the dense-packing mode distribute in a broader and deeper area as compared with the loose-packing mode, which results in higher ultimate bearing load. Moreover, it was found that in the loose-packing mode an increase in the vertical pressure load is accompanied with an increase in the soil settlement, while in the dense-packing mode the load-settlement curves show a pronounced peak. Comparison of bearing capacity ratios for the dense- and loose-packing modes demonstrated that the maximum benefit of GBM is achieved for rock-soil slopes in loose-packing mode. It was also found that by increasing the slope height, both the initial stiffness and the bearing load decreases. The results indicated a significant increase in the ultimate bearing load as the distance of the footing to the slope crest increases. For all the cases, a good agreement between the laboratory and numerical results was observed.

• Geomechanics and Engineering
• /
• 제29권5호
• /
• pp.509-522
• /
• 2022

Tail-grouting is an effective measure in shield engineering for filling the gap at the shield tail to reduce ground deformation. However, the gap-filling ratio affects the value of the gap parameters, leading to different surface settlements. It is impossible to adjust the fill ratio indiscriminately to study its effect, because the allowable adjustment range of the grouting quantity is limited to ensure construction site safety. In this study, taking the shield tunnel section between Chaoyanggang Station and Shilihe Station of Beijing Metro Line 17 as an example, the correlation between the tail-grouting parameter and the surface settlement is investigated and the optimal grouting quantity is evaluated. This site is suitable for conducting field tests to reduce the tail-grouting quantity of shield tunneling over a large range. In addition, the shield tunneling under different grouting parameters was simulated. Furthermore, we analyzed the evolution law of the surface settlement under different grouting parameters and obtained the difference in the settlement parameters for each construction stage. The results obtained indicate that the characteristics of the grout affect the development of the surface settlement. Therefore, reducing the setting time or increasing the initial strength of the grout could effectively suppress the development of surface subsidence. As the fill ratio decreases, the loose zone of the soil above the tunnel expands, and the soil deformation is easily transmitted to the surface. Meanwhile, owing to insufficient grout support, the lateral pressure on the tunnel segments is significantly reduced, and the segment moves considerably after being removed from the shield tail.

• 토지주택연구
• /
• 제7권4호
• /
• pp.271-279
• /
• 2016

Recently developed trenchless construction methods ensure stability for the ground settlement by inserting steel pipes along the underpass section and integrating steel pipes before ground excavation to form pipe-roof. This study is to confirm the reinforcing effect of pipe-roof by measuring lateral earth pressure acting on the underpass constructed by the STS (Steel Tube Slab) construction method. For this purpose, lateral earth pressure was measured at the left and right side of the pipe-roof after installing earth pressure cells. As a result, lateral earth pressure was measured with considerable reduction because the integrated pipe-roof shared surcharge. Therefore, economic design for the underpass could be expected by sharing design load by pipe-roof. In addition, construction cost was analyzed according to the design-load sharing ratio by pipe-roof. As pipe-roof shares design load by 40%, the total construction cost can decrease by almost 10% in the case of four-lane underpass.

• 한국지반공학회논문집
• /
• 제22권8호
• /
• pp.55-62
• /
• 2006

샌드매트의 설계는 연약지반의 압밀침하특성과 매트의 투수성이 상호 결합된 연성압밀해석에 의해 얻어지는 간극 수압거동에 의해 검토되어야 한다. 본 연구에서는 샌드매트의 수두분포에 대하여 Terzaghi 1차원 압밀방정식을 이용한 수치해석을 실시하여 준설모래를 샌드매트 재료로 이용한 성토모형실험의 결과와 비교분석하였다. 실험결과 단계 성토가 증가하면서 간극수압은 성토중심부에서 증가되는 침하량의 영향을 받고 있다. 그리고 잔류된 간극수압 영향으로 간극수압의 상승속도가 수치해석결과보다 지연되고 있다. 따라서 최종적으로 샌드매트 시공은 성토중심부에서 증가되는 동수구배를 저감시키도록 포설되어야 한다.

• 한국농공학회논문집
• /
• 제47권2호
• /
• pp.87-96
• /
• 2005

In this research, an attempt is made to derive the practical estimation of the degree of consolidation in soft clay from field measurements under embankments. For the practical estimation of pore water pressure in soft clay, the elasto-viscous rheological model was proposed, with a transform of parameters and a field geotechnical measurements in southern Korea. By using the rheological properties of soft clays and the dissipation of excess pore water pressure behaviour during step loading, a degree of consolidation or pore water pressure estimation in the future can be performed, and are shown to be generally close to the field measurements of pore water pressure. Finally, a pore water pressure behaviour in soft clay can be explained through measured data in field and the excess pore water pressure data can also be used to estimate settlement.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.551-558
• /
• 2001

The horizontal drain method is one of methods improving reclamation ground. This method reduces consolidation time by using drained installed horizontally, and negative pressure is applied on end of these drains by vacuum pump. But, effective negative pressure still wasn't evaluated in applying this method to reclamation ground. To estimate optimum negative pressure, soil box test that make a model the in-situ by installing horizontal drains in the center is performed pressing different vacuum pressure In the laboratory, and the variations in settlement and volume of drained water through the drains during consolidation process were measured. Also, water content with distance from drain and with depth is measured after the test.