• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.159-162
• /
• 2008

High pressure is involved during injection molding operation specially packing phase. Cracks in the mold are often occurred by high cavity pressure. In this study, structural analysis of mold has been performed using commercial softwares, Abaqus and Ansys, to investigate cause of crack in the injection mold. Structural analysis contains four cases: stress distribution according to the cavity pressure, stress concentration according to the boundary conditions, stress concentration for inter-locking design of mold, and stress concentration for distributed cavity pressure. Through this study it was observed that the locations of stress concentrations were coincident with locations of crack. Robust mold design is being required to withstand high cavity pressure.

• The Journal of the Petrological Society of Korea
• /
• v.6 no.2
• /
• pp.88-95
• /
• 1997

High pressure X-ray diffraction study was carried out on a polycrystalline graphite to investigate the phase transition(s) at room temperature. Energy dispersive X-ray diffraction method was employed using a Mao-Bell type diamond anvil cell with an Wiggler synchrotron Radiation at the National Synchrotron Light Source. Sodium chloride power was used as the internal pressure sensor for the high pressure determinations as well as the pressure medium for quasihydrostatic pressure environment. Graphite transforms into a hexagonal didose not agree with the previously reported observations and this phase persists when pressure is released down to 0.1 MPa. This result dose not agree with the previously reported observations and this discrepancy would be due to the kinetics in phase transition as well as the uniaxially oriented pressure field in the diamond anvil cell.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2289-2295
• /
• 2005

Two-Phase flow pattern and pressure drop data were obtained for pure refrigerants R134a and R123 and their mixtures as test fluids in a horizontal tube. The flow pattern is observed through tubular sight glasses located at inlet and outlet of the test section. The flow map of Baker developed for air-water two-phase flow at atmospheric pressure failed to predict the observed flow patterns at the higher value of the mass velocity used in the present study. The map of Kattan et al. predicted the data well over the entire region of mass velocity selected in the present study. The measured pressure drop increased with an increase in vapor quality and mass velocity. A new two-phase multiplier was developed from a dimensional analysis of the frictional pressure drop data measured in the present experiment. This new multiplier was found successfully to correlate the frictional pressure drop.

• Journal of Drive and Control
• /
• v.11 no.2
• /
• pp.1-8
• /
• 2014

In this study, the authors carried out experiments and numerical simulations in order to clarify the pressure pulsation characteristics in multiple-delivery rotating-cam and stationary-cylinder type radial piston pumps. Also, a tee filter was applied to the pump in order to mitigate the pressure pulsation. Through the experiments and simulations, it was known that pressure pulsation with a magnitude higher than 40% of the mean load pressure could occur in the pump used in the experiments. Moreover, it was confirmed that a tee filter designed in this study could effectively mitigate the pressure pulsation.

• Journal of Korean society of Dental Hygiene
• /
• v.23 no.2
• /
• pp.105-113
• /
• 2023

Objectives: The purpose of this study is to verify the usefulness and practicality of the program in the daily life of the elderly by performing a three-dimensional tongue muscle exercise for the elderly to identify the dysphagia, swallowing ability, and tongue pressure. Methods: The subjects of the study were 29 elderly people aged 65 or older living in Busan, divided into a oral exercises group and tongue strength training program combined with oral exercises group, and operated 16 times for 8 weeks twice a week, and the pre and post-program evaluation was conducted in the 1st and 8th weeks. For variable selection, 7 general characteristics, 5 oral health-related characteristics, 5 Likert scale for swallowing disorder, repetitive swallowing ability test for swallowing power measurement, and tongue pressure measurement was used. Data analysis was conducted using SPSS window program 25.0 version (IBM), general characteristics and homogeneity tests, oral health-related characteristics and homogeneity tests were chi-square test, swallowing disorder, swallowing ability, and change in tongue pressure were paired t-test, Wilcoxon signed rank test, t-test, Mann-Whitney U test for swallowing disorder and changes in swallowing ability and tongue pressure, and Spearman's correlation for the relationship between swallowing disorder and swallowing ability and tongue pressure. Results: As a result of tongue strength training program combined with oral exercise, both relieve swallowing disorder and improve low eating and tongue pressure than oral exercise, and the difference in improvement effects of both relieve swallowing disorder, swallowing ability, and tongue pressure is higher. Conclusions: Based on the results of this study, it is believed that simple and practical oral muscle function reinforcement products and practical use are needed, and institutional devices to seek oral health promotion programs for the elderly are needed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.201-208
• /
• 2002

In this paper, the control strategy of ratio changing system for a metal belt CVT adopting primary pressure regulation is developed, and the shirting performance of pressure regulating type CVT with the suggested control strategy is investigated. The control strategy suggested in this study is composed of 2 feedback loop, one is speed ratio feedback and the other is primary pressure feedback. The pressure feedback is adopted to ensure prohibiting a belt slip during transient period in a fast downshift mode. Simulation results show that the system with suggested control strategy gives appropriate response time and tracking Performance for upshift and also gives a proper primary pressure which can prohibit the belt slip. In addition, it is fecund that the given system has an acceptable servo property in tracking the target speed ratio and robustness for the disturbance of line pressure.

• Journal of Korean Association for Spatial Structures
• /
• v.2 no.1 s.3
• /
• pp.93-102
• /
• 2002

Pressure loads caused by gas, water and wind are the most important load cases in structural analysis. Often the pressure loads are approximated by constant directional loads since it is difficult to evaluate the exact value. However, the pressure load is defined as a displacement dependent one and it is necessary to consider the follower effects of the load in analysis procedure. In this study, the large deformation analysis considering geometrical nonlinearity for shell structures under pressure loads is presented. Finite element by using a three-node flat triangular shell element is formulated and the follower effects of the pressure load are included in the formulation. Some of results are presented for cantilevered beam under uniform external pressure and thin circular ring under non-uniform external pressure. The present results are in good agreement with the results available in existing literature and commercial software ABAQUS.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.92-99
• /
• 1996

The contact pressure in jointed plates was measured by means of an improved ultrasonic technique. In order to get calibration curve, the relationship between contact pressure and ratio of boundary and bottom echo of normal beam probes were obtained for the calibration blocks with various surface roughness. The ratio of boundary and bottom echoes were measured for the upper/under plates locally compressed with uniform pressure, and the distribution of contact pressure was obtaines. The measured pressure has a good agreement with results of FEM analysis. Thus the proposed ultrasonic method in this work is very useful to measure the contact pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.50-59
• /
• 1997

When a front head of train enters a tunnel at a high speed, compression wave is generated at tunnel entrance due to the confinement effect and propagated along the tunnel with sound of speed. The propagated compression wave is reflected at tunnel exit due to abrupt pressure change at passage. The reflected wave is expansion pressure wave. And when the rear head of train goes through the tunnel entrance, another expansion pressure wave is generated and propagated along the tunnel. The pressure drop occurs seriously around train when the two expansion pressure waves come cross on train in the tunnel. In order to reduce the pressure drop, the compression wave front must be controlled because the intensity and magnitude of pressure drop is nearly proportional to that of compression wave at tunnel entrance. This study relates to reduction of the pressure wave gradient with respect to tunnel entrance shape change with various kind of angle and rounding. The results show characteristics of wave propagation in tunnel, usefulness of characteristic curve to estimate proper time domain size in numerical study and measuring time in actual experiment. Also rounding is contributed to improve pressure wave front even if its radius is very small at tunnel entrance. In order to improve of pressure wave front at tunnel entrance, proper angle is prefered to rounding with big radius and an angle of around 14$^{\circ}$ is recommended according to this simulations, And it is expected to reduce additional pressure drop in tunnel when the location and the size of the internal space for attendant equipment are considered in advance.

• PNF and Movement
• /
• v.20 no.1
• /
• pp.9-17
• /
• 2022

Purpose: The purpose of this study was to investigate the effect of chest mobilization and stretching exercises on maximal inspiratory pressure and maximal expiratory pressure in healthy adults who use computers for extended periods of time each day due to coronavirus disease 2019. Methods: Twenty-five healthy adults in their 20s and without respiratory disease (15 female, 10 male) took part in this study. Two types of thoracic mobilizing exercises using a Theraband and three types of stretching exercises using a foam roller were performed. Maximum inspiratory pressure and maximum expiratory pressure were measured three times each before and after the interventions. In terms of statistical methods, the maximum inspiratory pressure due to chest mobility and stretching was compared with the maximum expiratory pressure using parametric paired t-test and non-parametric Wilcoxon signed-rank test. Results: Maximum inspiratory pressure (p = .012) and maximum expiratory pressure (p = .006) showed significant differences before and after chest mobilization exercise and stretching among the participants. Conclusion: The results of this study suggest that chest mobilization and stretching exercises are effective exercise methods for improving maximal inspiratory and expiratory pressure. They suggest that these exercises can prevent respiratory muscle weakness and improve aerobic fitness in healthy people as well as those in need of cardiorespiratory physiotherapy.