• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1182-1188
• /
• 2010

This paper proposes a precise localization algorithm for a quickly moving mobile robot. In order to localize a mobile robot with active beacon sensors, a relatively long time is needed, since the distance to the beacon is measured using the flight time of the ultrasonic signal. The measurement time does not cause a high error rate when the mobile robot moves slowly. However, with an increase of the mobile robot's speed, the localization error becomes too high to use for accurate mobile robot navigation. Therefore, in this research into high speed mobile robot operations, instead of using two active beacons for localization an active beacon and dual compass are utilized to localize the mobile robot. This new approach resolves the high localization error caused by the speed of the mobile robot. The performance of the precise localization algorithm was verified by comparing it to the conventional method through real-world experiments.

• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.632-639
• /
• 2010

Ground Transportation is one of the most required field that users need positioning information Especially, more precise position can make smart traffic management possible and bring convenience to users. By advanced wireless network, cars can receive the GPS information of reference station in any tim e and any where. Thus land vehicles are possible to process precise positioning. In general, for precise positioning code and phase measurements are used. But receivers provide not only code and phase measurements but also doppler measurements and Doppler is direct measurement of velocity. In this paper, because velocity is very important information required in Ground Transportation, precise positioning for Ground Transportation is studied. For precise positioning RTK(Real-Time Kinematic) was used and double differenced doppler measurements were added, As a Result, positioning error by multipath and cycle slip was soften. However there still remained Positioning error. Thus smoothing technique using doppler measurement in position domain is used for softening positioning error.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.1
• /
• pp.693-700
• /
• 2009

For real-time precise GPS data processing such as a long baseline network RTK (Real-Time Kinematic) survey, PPP (Precise Point Positioning) and monitoring of ionospheric/tropospheric delays, it is necessary to guarantee accuracy comparable to IGS (International GNSS Service) precise orbit with no latency. As a preliminary study for determining near real-time satellite orbits, the general procedures of satellite orbit determination, especially the dynamic approach, were studied. In addition, the transformation between terrestrial and inertial reference frames was tested to integrate acceleration. The IAU 1976/1980 precession/nutation model showed a consistency of 0.05 mas with IAU 2000A model. Since the IAU 2000A model has a large number of nutation components, it took more time to compute the transformation matrix. The classical method with IAU 2000A model was two times faster than the NRO (non-rotating origin) approach, while there is no practical difference between two transformation matrices.

• Journal of Positioning, Navigation, and Timing
• /
• v.8 no.4
• /
• pp.209-214
• /
• 2019

Precise point positioning (PPP) requires precise orbit and clock products. International GNSS service (IGS) real-time service (RTS) data can be used in real-time for PPP, but it may not be possible to receive these corrections for a short time due to internet or hardware failure. In addition, the time required for IGS to combine RTS data from each analysis center results in a delay of about 30 seconds for the RTS data. Short-term orbit prediction can be possible because it includes the rate of correction, but the clock correction only provides bias. Thus, a short-term prediction model is needed to preidict RTS clock corrections. In this paper, we used a long short-term memory (LSTM) network to predict RTS clock correction for three minutes. The prediction accuracy of the LSTM was compared with that of the polynomial model. After applying the predicted clock corrections to the broadcast ephemeris, we performed PPP and analyzed the positioning accuracy. The LSTM network predicted the clock correction within 2 cm error, and the PPP accuracy is almost the same as received RTS data.

• Journal of Advanced Navigation Technology
• /
• v.14 no.6
• /
• pp.783-790
• /
• 2010

For safety navigation of ships at sea, ships monitor their location obtained from Global Positioning Satellite System (GNSS). In this study, we computed near-real-time positions of a ship at sea using GPS Precise Point Positioning (PPP) technique and analyzed precision of the near-real-time positions. We conducted ship borne GPS observations in the south sea of Korea. To process the GPS data using PPP technique, GIPSY-OASIS (GPS Inferred Positioning System-Orbit Analysis and Simulation Software) developed by the Jet Propulsion Laboratory was used. Antenna phase center variations, ocean tidal loading displacements, and azimuthal gradients of the atmosphere were corrected or estimated as standard procedures of high-precision GIPSY-OASIS data processing. As a result, the precisions of near-real-time positions was ~1cm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.9
• /
• pp.1846-1855
• /
• 2015

In this paper, a precise relative positioning with TD(time differenced) carrier phase measurements from a low-cost GNSS(Global Navigation Satellite System) receiver is proposed and analysed. The proposed method is using carrier phase measurement from a single GNSS receiver that reference receiver is not required and stand alone positioning is possible. TD operation removes the troublesome integer ambiguity resolution problem, and if the time interval is short, other error, such as, ionospheric, tropospheric delay and ephemeris error are effectively eliminated. The error analysis of the proposed method shows that a precise and positioning with carrier phase is possible. The implemented system is evaluated using a real car experiments. The results show that the horizontal positioning error was less than 3m during 10 minutes experiments, which is 4 times more precise than the results of normal code based absolute positioning.

• The KIPS Transactions:PartC
• /
• v.13C no.1 s.104
• /
• pp.95-102
• /
• 2006

Nowadays, GPS is used widely, especially in case which needs precise position information, such as car navigation systems and various kinds of position measuring instruments in an outdoor environment. According to their applications, there are many kinds of GPS receivers with different costs and error rates. The maximum error range of the general-purpose GPS receiver is within 30m, though the error rate depends on receiving rate of signal and weather condition. RTK(Real-Time Kinematic) and DGPS(Differential Global Positioning System) have more precise accuracy than the general-purpose GPS. However end users can't afford use them because of their high price and large size of equipments. In order for the end user to obtain precise position information, it is important that GPS receivers has portability and low price. In this study, we introduce a new system that offers precise position information using the DGPS mechanism satisfying low cost and portability.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.4
• /
• pp.235-243
• /
• 2018

Conventional Real Time Kinematics (RTK) collect measurements in stationary state for several minutes to resolve the integer ambiguity in the carrier phase measurement or resolve the integer ambiguity on the move assuming low maneuvering movement. In this paper, an On The Move-RTK (OTM-RTK) technique that resolves the integer ambiguity on the move for fast and precise positioning of ground vehicles such as high maneuvering vehicles was proposed. The OTM-RTK estimates the precise amount of movement between epochs using the carrier phase measurements acquired on the move, and by using this, resolves the integer ambiguity within a short period of time by evaluating the integer ambiguity candidates for each epoch. This study analyzed the integer ambiguity resolution performance using field driving experiment data in order to verify the performance of the proposed method. The results of the experiment showed that the precise trajectory including the initial position bias can be obtained prior to resolving the integer ambiguity, and after resolving the integer ambiguity on the move, it was possible to obtain the bias-corrected precise position solution. It was confirmed that the integer ambiguity can be resolved by collecting measurements of about 10 epochs from the moving vehicle using a dual frequency receiver.

• Journal of Auto-vehicle Safety Association
• /
• v.9 no.2
• /
• pp.6-12
• /
• 2017

An autonomous driving system based on a precise digital map is developed. The system is implemented to the Hyundai's Tucsan fuel cell car, which has a camera, smart cruise control (SCC) and Blind spot detection (BSD) radars, 4-Layer LiDARs, and a standard GPS module. The precise digital map has various information such as lanes, speed bumps, crosswalks and land marks, etc. They can be distinguished as lane-level. The system fuses sensed data around the vehicle for localization and estimates the vehicle's location in the precise map. Objects around the vehicle are detected by the sensor fusion system. Collision threat assessment is performed by detecting dangerous vehicles on the precise map. When an obstacle is on the driving path, the system estimates time to collision and slow down the speed. The vehicle has driven autonomously in the Hyundai-Kia Namyang Research Center.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.9
• /
• pp.883-890
• /
• 2006

Nowadays, CPS is used widely, especially in cases which need more precise position information, such as car navigation systems and even in the mobile robot for position measuring in the outdoor environment. RTK (Real-Time Kinematics) and DGPS (Differential Global Positioning System) have more precise accuracy than the general-purposed GPS. However can't easily use them because of high prices and large size of equipments. In order fur the mobile robot to obtain precise position information it is important that CPS receiver has portability and low price. In this study, we introduce a new GPS data acquisition system that offers the precise position data using the DGPS mechanism and satisfying low cost and portability. In addition to this, we propose an improved data compensation algorithm that offers more accurate position information to the outdoor mobile robot by compensating the error rate of CPS data measured from the three points with geometrical rotation and distance formula. Proposed method is verified by comparing with the precise real position data obtained by RTK. Proposed method has more than 70% performance enhancement.