• The KSFM Journal of Fluid Machinery
• /
• v.12 no.2
• /
• pp.46-51
• /
• 2009

Recently, microturbines have received attention as a small-scale distributed power generator. Since the exhaust gas carries all of the heat release, generating hot water is usual method of heat recovery from microturbine CHP (combined heat and power) systems. The power of microturbines decreases as ambient temperature increases. This study predicted micoturbine power boost by injecting hot water generated by heat recovery. Influence of injecting water at two different locations was examined. Water injection improves power, but efficiency depends much on the injection location. Injecting water at the compressor discharge shows a much higher efficiency than the combustor injection. However, the combustor injection may have as much available cogeneration heat as the dry operation, while the available heat in the compressor discharge injection is much smaller than the dry operation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.4
• /
• pp.297-302
• /
• 2019

In this paper, the power generation efficiency increase has been studied for a Rankine cycle using both supercritical carbon dioxide as a working fluid and LNG as a coolant with PRO/II with PROVISION release 10.0 from Aveva company. Peng-Robinson equation of the state model with Twu's alpha function was selected for the modeling of the power generation cycle using LNG cold heat. Power generation efficiency was increased from 24.82% to 57.76% when using LNG as a coolant for supercritical carbon dioxide power generation cycle.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.1
• /
• pp.49-55
• /
• 2010

The purpose of the study was to analyze kinetic factors required to the three-point jump shot of the basketball games through 3-D analysis and ground reaction force(GRF) analysis. Six university male players participated in this study. The results of the study were showed that (1) resultant velocity in the center of mass(COM) was $0.84{\pm}0.27\;m/s$ since a player didn't shot a ball in the highest peak and shot ball at the moment of going up forward and vertical movement. Therefore, it is necessary to find a proper timing to shot a ball; (2) the angular velocity was largely increased in upper arm and fore arm out of the upper-limb segments and the hands had the largest angular velocity since the body is in a fixed situation and angular speed is rapidly increased by the wrist' snap with the rapid movement of upper arm and forearm at the time of release a ball; (3) it is judged that a player can shot a ball at the accurate and high release point when the player collects power vertically to the maximum by keeping GRF to the right and the rear in a proper way and by keeping the body's balance so that a large power may not be dispersed.

• Fire Science and Engineering
• /
• v.21 no.2 s.66
• /
• pp.98-104
• /
• 2007

This study is related with the fire risk assessment for fire area at nuclear power plant by use of FDS (Fire Dynamics Simulator) that is a computational fluid dynamics (CFD) model of fire-driven fluid flow. The major purpose of this research is to analyze the sensitivity of the fire modeling when the heat release rate that is an important input variable is changed as well as when the grid size that is a critical factor of the fire model is modified. The result is presented at the conclusion with some comments for CFD model application.

• Nuclear Engineering and Technology
• /
• v.28 no.6
• /
• pp.507-521
• /
• 1996

Quantification of uncertainties in the source term estimations by a large computer code, such as MELCOR and MAAP, is an essential process of the current Probabilistic safety assessment. The main objective of the present study is to investigate the applicability of a combined procedure of the response surface method (RSM) based on input determined from a statistical design and the Latin hypercube sampling (LHS) technique for the uncertainty analysis of CsI release fractions under a Hypothetical severe accident sequence of a station blackout at Younggwang nuclear power plant using MAAP3. OB code as a benchmark problem. On the basis of the results obtained in the present work, the RSM is recommended to be used as a principal tool for an overall uncertainty analysis in source term quantifications, while using the LHS in the calculations of standardized regression coefficients (SRC) and standardized rank regression coefficient (SRRC) to determine the subset of the most important input parameters in the final screening step and to check the cumulative distribution functions obtained by RSM. Verification of the response surface model for its sufficient accuracy is a prerequisite for the reliability of the final results that can be obtained by the combined procedure proposed in the present work.

• Nuclear Engineering and Technology
• /
• v.17 no.4
• /
• pp.267-278
• /
• 1985

Some kinds of methods have been applied to regulate the exposure doses by the radioactive effluents from nuclear power plants. The essential one is primary dose equivalent limit recommended by the ICRP. When the primary limit cannot be applied directly for regulation, there have been dose equivalent index in case of external exposure, or maximum permissible concentration, annual limit on intake, derived air concentration and maximum permissible body burden in case of internal exposure. But the derived limit is required from the viewpoint of discharge, for those values are inadequate to control discharge rate directly. This study was carried out to derive the release limit for the Wolsung nuclear power plant by the concentration factor method. This method is based on the assumption of steady state transfer between environment compartments.

• Nuclear Engineering and Technology
• /
• v.51 no.2
• /
• pp.410-423
• /
• 2019

Fire suppression using a water mist nozzle directly above an n-Heptane pool in a fire compartment with a door opening was numerically investigated using the Fire Dynamics Simulator (FDS) for the purpose of application in nuclear power plants. Input parameters for the numerical simulation were determined by experimental measurements. Water mist was activated 10 s after the fire began. The sensitivity analysis was conducted for three input parameters: total number of cubic cells of 6032-2,926,400, droplets per second of 1000-500,000, and extinguishing coefficient of 0-100. In a new simple calibration method of this study, the extinguishing coefficient yielding the fire suppression time closest to that measured by experiments was found for use as the FDS simulation input value. When the water mist jet flow made contact with the developed fire, the heat release rate instantaneously increased, and then rapidly decreased. This phenomenon occurred with a displacement of the flame near the liquid fuel pool. Changing the configuration of the door opening with different aspect ratios and opening ratios had impact on the maximum value of the heat release rate due to the flame displacement.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3559-3570
• /
• 2023

In the decommissioning of nuclear facilities, Derived Concentration Guideline Level (DCGL) derivation is necessary for the release of the facility after the site remediation, which also needs to be implemented in the stage of establishing a decommissioning planning. In order to derive DCGL, the dose assessment for the receptors can be conducted from residual radioactivity by using RESRAD code. When performing sensitivity analysis on probabilistic parameters, secondary evaluation is performed by assigning a single value for parameters classified as sensitive. However, several options may arise in the handling of nonsensitive parameters. Therefore, we compared the results of the first execution of RESRAD applying probabilistic parameters for each scenario with the results of the second execution applying a single value to sensitive parameters among the probabilistic parameters. In addition, we analyzed the effect of setting options for non-sensitive parameters. As a result, the effect on DCGL were different depending on the application scenario, the target radionuclides, and the input parameter selections. In terms of the overall evaluation period, the DCGL graph of the default option was generally shown as the most conservative except for some radionuclides. However, it will not necessarily be given priority in the aspect of the need to reflect site characteristics. The reason for selecting a probabilistic parameter is the availability of the parameter and the uncertainty of applying a single value. Therefore, as an alternative, it can be consistently applied to distribution as an option for non-sensitive parameters after sensitivity analysis.

• Applied Biological Chemistry
• /
• v.15 no.2
• /
• pp.143-162
• /
• 1972

Based on the concentration of $^{40}K$ naturally occurring radioisotope of potassium, a method for the determination of total potassium in soils and plants was developed. The method was extended to evaluate the potassium supplying power of soils by taking the ratio of exchangeable potassium to total potassium $(K_{ex}/K_t)$, termed the potassium buffering capacity. Using this as index, it was observed that the release of potassium from soil fellows the from order reaction. A linear relationship was found between the potassium buffering capacity and the release constant of potassium or mica content of the clay. Similarly the potassium buffering capacity was also closely correlated with total uptake of potassium by rice plant. Hence it is concluded that the method for determining of the potassium buffering capacity could be veil applied to characterize the potassium availability of soils. The method for the determination of potassium is characterized by (1) The efficient measurement of the weak beta activity emissions from the samples, (2) identification of $^{40}K$, (3) calculation of total potassium content using the proportional constant of $^{40}K$ of samples to that of the standard. Difference in the potassium supplying power of soils due to soil types was also evaluated with the use of this technique. The degree of the potassium supplying power was in the order of soil types as red-yellow podzolic and lateric soils, basaltic materials(Rvd)> low-humic gley and alluvial soils, alluvial plains and food plains(Apa)> low-humic gley soils, nearly level to sloping local alluvial plains and slopes(Afb)> low-humic gley and alluvial soils, fluvio-marine plains (Fma).

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.178-185
• /
• 2002

The object of this paper is to investigate the effects of early fuel evaporators on cold driveability of gasoline passenger cars. Experiment has been carried out for the assessment cold start performance and cold driveability. And fuel consumption rate, emission and cylinder pressure were measured. On the base of combustion pressure of cylinder, rate of heat release, cumulative heat release amount and burned mass fraction are evaluated. The results show that fuel consumption rate is increased by 17.7%, monoxide and hydrocarbon were reduced by 23% and by 45% respectively, fluctuations of indicated mean effective pressure and maximum combustion pressure were increased by 4∼6%, fuel consumption rate per power was improved by 0.2∼2.3%. These are caused by the fact maximum heat release period and main combustion period are getting short.