• 소성∙가공
• /
• 제8권2호
• /
• pp.135-142
• /
• 1999

Tube Process(TP) is one of the processes to produce permanent magnets. Advantage claimed for this process is that it can accmplish both densification and anisotropication in one step forming. This process is distinguished from other processes since it uses deformable tube for densification of powder magnets. TP has, however, difficulties in manufacturing permanent magnets from Nd-Fe-B green powder due to folding resulted from large height reduction and localized densification. Therefore, an adequate preform is necessary to reduce folding resulted from large height reduction and localized densification. Therefore, an adequate preform is necessary to reduce folding, lead magnets into almost desired final shape and get uniform densification. In this paper, preform design for TP is carried out without a deformable tube to investigate the behaviour of magnet sinter-forging. Preform design is accomplished to increase the effective magnet area with a near net shape and uniform densification.

• 한국세라믹학회지
• /
• 제34권2호
• /
• pp.115-122
• /
• 1997

액상 분말 합성법 중의 하나인 에멀젼 건조 방법에 의한 분말 합성은 조성 조절이 용이하고 균질한 미립자 분말을 제조할 수 있는 장점을 지니고 있다. 에멀젼 건조법을 사용하여 합성 분체의 초기 형상과 입도를 제어하고 근본적으로 더욱 개선된 homogeneity를 얻었다. 에멀젼의 분리를 억제시킬 수 있는 계면활성제, 오일상 및 수용액의 혼합비를 조절함으로써 Bi(Pb)-Sr-Ca-Cu-O 초전도 분말을 제조할 수 있었다. 이 방법에 의하여 합성된 산화물 초전도체 분말의 특성 및 pellet으로 성형한 시편을 열처리하여 미세구조와 전기적 특성을 조사하였다. 또한, OPIT(Oxide Powder-in-tube)법에 의해 테이프를 제작하여 미세구조와 전기적 특성을 관찰하였다. 합성된 분말의 입자크기는 1$\mu$m이하의 구형이었으나 대부분이 2~5$\mu$m크기로 응집되어 있었다. Ar분위기의 1/13atm 산소분압(Po2)에서 84$0^{\circ}C$로 72시간 동안 열처리한 덩어리형 시편의 임계저항온도는 108K이었으며, 1차와 2차 열처리한 테이프의 임계전류는 각각 0.4A와 1.5A이었다.

• Advances in Energy Research
• /
• 제8권3호
• /
• pp.155-163
• /
• 2022

The current study presents experimental research on a parabolic trough collector with tube and cavity receivers. The primary concentrating parabolic reflector is designed for an aperture area of 2×2 m² with mirror-polished stainless steel sheet reflectors. The cavity receiver consists of a compound parabolic secondary reflector and a copper tube. Both the conventional tube receiver and the cavity receiver tube are coated with black powder. The experiments are carried out to compare the efficiency of the cavity receiver with the tube receiver for fluid temperature rise, thermal efficiency, and overall losses. The experiments showed significantly higher fluid temperature rise and overall efficiency and lower thermal losses for the cavity receiver compared to the tube receiver within the parameters explored in this study.

• 한국레이저가공학회지
• /
• 제3권3호
• /
• pp.21-29
• /
• 2000

For the direct metal shape processing the powder feed device which is different from the widely used in rapid prototyping. is developed, The three dimensional object is shaped with the melting metal powder. The developed research has applied to rapid prototyping in ultraprecision for MEMS and medical science fields required of rapid manufacture of complex shape. The goal of this study make 3D model which has precision accuracy. Powder spreading apparatus has been more improved because that the control of powder spread is very important in layer manufacturing. It consists of the vibration motor, nozzle and tube which supplies various metal powder. This apparatus could control the spreading velocity that could control powder spreading thickness. Laser on/off switch was adapted because laser scanning velocity must be preserved constantly to prevent heat transformation of laser overheating. The error between sintered thickness md experimental one occurred by shrinkage in sintering melting process. The problem of heat transformation was solved by On/Off switching system.

• 한국분말재료학회지
• /
• 제6권3호
• /
• pp.238-245
• /
• 1999

The preparation of $n-TiO_2$ powder by the Chemical Vapor Synthesis process (CVS) was studied using the liquid metal organic precursor (TTIP). The residence time and the collection methods were considered as main processing variables through the experiments. The CVS equipment consisted of a micropump and a flashvaporizer, a tube furnace and a tubular collection device. The synthesis was performed at $1000^{\circ}C$ with various sets of collection zone. The residence time and the total system pressure were controlled in the range of 3~20 ms and 10 mbar, respectively. Nitrogen adsorption, X-ray diffraction and electron microscopy were used to determine particle size, specific surface area and crystallographic structure. The grain size of the as-prepared $n-TiO_2$ powder was in the range of 2~8 nm for all synthesis parameters and the powder exhibited only little agglomeration. The relationship between particle characteristics and the processing variables is reviewed based on simple growth model.

• 한국분말재료학회지
• /
• 제8권1호
• /
• pp.20-25
• /
• 2001

Most of mold manufacturing procedures have been automated by the introduction of NC machine tool and CAD/CAM system. But the three-dimensional surface curvature of the mold must be done by hand work of well-skilled workers. Magnetic abrasive polishing powders were investigated for surface polishing for 3D curvature. This study aims to investigate homogeneously distributed hard phase in Fe matrix and strong bonding between Fe-matrix and hard phase. The NbC powder, $B_4C$ powder and $Al_2O_3$ powder were mixed in Fe-matrix respectively. Mixed Fe-hard phase powders were compacted by press and then these were melted by plasma melting. According to SEM, XRD and OM observation, Fe-NbC magnetic abrsive powder had the most homogeneous distribution and strong bonding. As a result of magnetic polishing, the surface roughness before magnetic polishing, 1 ${\mu}m$ $R_{max}$, was reduced to 0.2 ${\mu}m$ $R_{max}$ over the entire inner surface of the tube.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.527-530
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in term of different diameter, length and thickness by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050^{\circ}C{\sim}1100^{\circ}C\;amd\;550^{\circ}C$ for 30min, respectively. The mould renting speed was 1000rpm. A tube was annealed at $840^{\circ}C$ for 72hours in oxygen atmosphere. The plate-like grains were well developed along the renting direction and typical grain size was about more than $40{\mu}m$. It was found that Ic values increased with increasing the tube diameter while the Ic decreased with increasing tube thickness. Also Ic decreased with increasing the tube length. The measured Ic in $50mm{\times}70mm{\times}25mm$ tube was about 896Amp.

• Progress in Superconductivity
• /
• 제7권2호
• /
• pp.174-178
• /
• 2006

For the practical application on SCFCL, Bi2212 tubes were fabricated by Centrifugal Forming Process (CFP) in terms of many different processing parameters. Typical sizes of tubes were 60, 150 mm in length and 2.5, 3.5, 4.8 mm in thickness. Initially powder was melted by induction heating. The optimum range of melting temperatures and preheating temperature were $1100^{\circ}C$ and $500^{\circ}C$ for 30min respectively. The nominal mold rotating speed was around 1000 RPM. A tube was annealed at $840^{\circ}C$ for 80 hours in oxygen atmosphere. The tube of 50mm x 70mm x 2.5mm, rotated with 1000 RPM showed $I_c=890\;A\;and\;T_c=80$. It was found that the tube processed with faster rate of mold rotation speed, thinner tube thickness and shorter tube length shows better electric characteristics as compared with the tube normally processed. In order to study the uniformity heat and fluid flow analysis tool was adopted along tube.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• Journal of Chest Surgery
• /
• 제26권7호
• /
• pp.532-537
• /
• 1993

To assess the therapy of spontaneous pneumothorax in the aged patients, the treatment methods and results in 60 patients 50 years of age or older were retrospectively reviewed. Most of the patients were male [56 of 60 patients] and the major underlying lung diseases associated with spontaneous pneumothorax were tuberculosis [32 patients] and chronic obstructive lung disease [20 patients]. The recurrence rate of thoracostomy tube drainage with or without chemical pleurodesis using tetracycline was 39.6% [21 of 53 patients], but there was no recurrence in the patients treated with open thoracotomy, pleural abrasion, and chemical pleurodesis using talcum powder[Asbestosis free]. In the patients treated with open thoracotomy, the bullous or bleb lesions were placed in the various sites of both lungs. We concluded that even though thoracostomy tube drainage is the first choice of therapy for spontaneous pneumothorax in the aged patients, the recurrence rate is high, especially in the patients with persistent air leakage for more than 2 days, and the open thoracotomy with pleural abrasion and chemical pleurodesis using talcum powder can prevent the recurrence in the selected patients.